AD746JR - Dual 13MHz Precision BiFET Op Amp | Analog Devices
N.º de pieza: AD746JR ✓ ActivoAD746JR Descripción general
An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain and negative feedback to amplify weak differential signals with high input impedance and low output impedance. Within the amplifier hierarchy, the AD746JR is a voltage-feedback BiFET precision amplifier: a BiFET input stage, dual-channel architecture, and monolithic construction distinguish it from general-purpose CMOS amplifiers and comparators. This combination makes it suitable for instrumentation, filtering, and precision conversion interfaces.
The AD746 datasheet identifies a single-pole response that settles to 0.01% in 500 ns. It also specifies a very low total harmonic distortion of 0.0001%. These characteristics support fast-settling buffer stages for 12-bit and 14-bit DACs and ADCs. The dual architecture also allows one channel to buffer a reference while the other performs amplification, although simultaneous precision performance remains tied to matching load impedances and balanced layout.
Mechanically, the AD746JR uses an 8-pin SOIC package and is identified by the JR ordering code. The precision and BiFET characteristics inherited from the AD744 core give the device low input bias behavior and good DC precision, while the monolithic implementation improves channel-to-channel matching. Applications include low-frequency active filters, audio preamplifier stages, sample-and-hold interfaces, and precision ADC or DAC input buffers.
When using the device, follow the manufacturer's recommended power-supply bypassing and observe the input common-mode range for the selected supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths. Stable feedback components and careful grounding are essential because the fast settling response can expose instability in poorly compensated filter stages.
This page combines the AD746JR electrical characteristics, drop-in alternatives, application guidance, and practical design notes in one engineering-focused reference. It also identifies where the device differs from related dual JFET-input amplifiers, helping designers balance precision, speed, supply range, and channel matching when selecting an amplifier for an existing design.
Alternativas directas para AD746JR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con AD746JR (mismo factor de forma y huella) — difiere en Amplifier Type, Gain-Bandwidth Product, Package, Slew Rate, Supply Voltage Range.
AD746JRZ
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AD745JR-16
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →AD743JR-16
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →AD744JR
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TL072IDT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AD746JR Valores máximos y características eléctricas
| Amplifier Type | Dual precision BiFET operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 13 MHz |
| Slew Rate | 75 V/µs |
| Supply Voltage Range | ±4.5 V to ±18 V |
| Maximum Total Supply Voltage | 36 V |
| Settling Time | 500 ns to 0.01% |
| Total Harmonic Distortion | 0.0001% |
| Input Stage | BiFET |
| Internal Amplifier Core | Two AD744 amplifiers on a single monolithic die |
| Encapsulado | 8-pin SOIC |
| Tipo de montaje | Surface mount |
| Channel Matching | Close AC and DC matching on a common die |
| Estado RoHS | unknown |
Configuración de pines de AD746JR
| Pin 1 | OUT A — Channel A output |
| Pin 2 | -IN A — Channel A inverting input |
| Pin 3 | +IN A — Channel A non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | +IN B — Channel B non-inverting input |
| Pin 6 | -IN B — Channel B inverting input |
| Pin 7 | OUT B — Channel B output |
| Pin 8 | V+ — Positive supply connection |
Aplicaciones típicas
AD746JR es adecuado para 6 aplicacións: Precision ADC Input Buffer, High-Speed DAC Output Buffer, Active Audio Preamplifier, Low-Frequency Active Filter, Instrumentation Signal Conditioning, Sample-and-Hold Interface.
Precision ADC Input Buffer
The AD746JR fits between a high-impedance source and the sampling input of a 12-bit or 14-bit ADC because its 500 ns settling to 0.01% and 75 V/µs slew rate reduce acquisition errors. Place one channel ahead of the converter input and use the second channel for a reference buffer when channel matching matters. The 13 MHz gain-bandwidth product provides useful closed-loop margin at moderate gains, while the JFET input stage avoids the higher bias current associated with bipolar transistor inputs. Confirm converter acquisition time, input capacitance, and sampling kickback before finalizing the feedback network.
Recomendado
High-Speed DAC Output Buffer
The AD746JR can buffer the output of a 12-bit or 14-bit DAC where fast settling and low distortion are required. Its 500 ns settling to 0.01% and 0.0001% total harmonic distortion help preserve converter-code accuracy and reduce distortion in analog signal paths. The dual-channel implementation can drive two related DAC outputs while benefiting from the close AC matching inherent in a monolithic die. Isolate the amplifier from the DAC with the resistor value recommended by the converter manufacturer, and confirm output swing and capacitive-load stability for the chosen gain configuration.
Recomendado
Active Audio Preamplifier
The AD746JR is appropriate for low-noise audio preamplification because its BiFET input stage supports high input impedance and its 0.0001% total harmonic distortion keeps harmonic products low. The 13 MHz gain-bandwidth product provides more bandwidth than many general-purpose audio amplifiers, allowing moderate-gain stages to retain phase margin and accurate frequency response. The two channels can process stereo signals with close matching, but common-mode range and output-swing limits must be checked at the lowest supply voltage used in portable or battery-powered equipment.
Recomendado
Low-Frequency Active Filter
The AD746JR is well suited to precision active-filter stages because its 13 MHz gain-bandwidth product, 75 V/µs slew rate, and close DC characteristics support accurate gain and phase control. The amplifier can implement low-pass, high-pass, or band-pass sections with external resistors and capacitors, provided the loop gain and phase margin remain adequate at the highest operating frequency. Its rapid settling also makes it useful in switched-capacitor and sampled-data interfaces where accumulated delay would otherwise degrade system timing. Verify resistor ratios, capacitor tolerance, and common-mode headroom in the final filter design.
Recomendado
Instrumentation Signal Conditioning
The AD746JR can condition outputs from sensors, strain gauges, or laboratory probes when high input impedance, low distortion, and rapid settling are important. The BiFET input stage avoids loading weak sources, while the dual arrangement allows one channel to amplify a measurement and the other to generate or buffer a reference. The device is particularly useful where 12-bit or 14-bit measurement resolution is targeted without requiring a rail-to-rail amplifier. Confirm the sensor output range against the input common-mode limits and maintain symmetrical layout around both channels to preserve matching.
Recomendado
Sample-and-Hold Interface
The AD746JR can serve as a buffer around a sample-and-hold stage or between a switching node and a downstream converter when fast settling is essential. Its 500 ns response to 0.01% reduces the time required after each acquisition, and its 75 V/µs slew rate allows it to reproduce moderate-amplitude steps with limited distortion. The JFET input stage also presents low bias current to the sampling network, which is valuable when the source impedance is high. Check the hold-capacitor droop, switch feedthrough, amplifier input bias, and settling tolerance as a complete time-domain error budget.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para AD746JR — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Use the AD745JR-16 or AD743JR-16 only when their lower speed is acceptable and the common package reduces redesign effort. The TL072IDT is a cross-brand option for conventional low-frequency dual JFET stages, but its 3 MHz gain-bandwidth product leaves substantially less margin for fast-settling applications. For any substitution, verify the pin description, common-mode range, output swing, offset, bias current, noise, load drive, and closed-loop stability rather than relying on package shape alone.
Comparación con alternativas
| Parámetro | Este producto | AD746JRZ | AD745JR-16 | AD743JR-16 | AD744JR | TL072IDT |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Texas Instruments |
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Input Stage | BiFET | BiFET | BiFET | BiFET | BiFET | JFET |
| Channel Count | 2 | 2 | 2 | 2 | 1 | 2 |
Diferenciadores clave
- Faster speed than the lower-bandwidth AD74x family (frente a AD743JR-16)
- Higher gain-bandwidth product for wide-band filtering (frente a TL072IDT)
- Fast 0.01% settling for converter interfaces (frente a TL072IDT)
- Monolithic dual-channel matching (frente a AD744JR)
Notas de diseño
Place the supply-decoupling capacitor close to pin 8 and connect pin 4 to the ground or supply-return plane with a short, low-impedance path. Keep the two amplifier channels on the same side of the analog signal flow where matching matters, and provide identical input and feedback networks where channel-to-channel tracking is important. Route sensitive input traces away from switching-regulator outputs, digital clock lines, and high-current return paths.
Do not treat the SOIC-8 outline as proof of electrical interchangeability. Confirm the pin description for every substitute, especially input and output assignments across both amplifiers. Also check the common-mode range at the lowest supply voltage, output swing into the intended load, offset and bias-current limits, and closed-loop stability. An amplifier can fit the same PCB land pattern while still changing system accuracy or noise performance.
The 500 ns settling specification applies to a defined small-signal condition and does not guarantee final accuracy for large steps or capacitive loads. For ADC and DAC interfaces, include amplifier slew time, feedback-network delay, sampling kickback, and converter acquisition time in the timing budget. If the amplifier drives a sampling capacitor directly, evaluate isolation-resistor and compensation methods rather than relying on the bandwidth rating alone.
Use a supply arrangement that keeps the total voltage and polarity within the manufacturer's operating limits. Decoupling requirements become more important when the AD746JR drives long feedback traces or high-capacitance nodes, because extra loop delay can reduce phase margin. For dual-supply systems, provide adequate bypass capacitance on each rail rather than relying on a single bulk capacitor to suppress high-frequency transients.
Información de cumplimiento
The AD746JR is a general-purpose precision analog amplifier; automotive qualification is not indicated for this ordering code. Confirm terminal-finish and material-compliance documentation with Analog Devices for the exact production configuration.