CD4051BPW - 20V 8:1 CMOS Analog Multiplexer | Texas Instruments
N.º de pieza: CD4051BPW ✓ ActivoCD4051BPW Descripción general
An analog multiplexer is a semiconductor switch that connects one common terminal to one of several channel terminals according to binary control signals. The CD4051 belongs to the CD4000 CMOS logic family, combining analog signal switching with digital address control. Its broad supply-voltage range supports legacy and industrial systems, while logic-level conversion helps the address interface operate reliably when the control logic uses a lower voltage than the analog supply.
Key features include an 8:1 multiplexing configuration, a maximum 20 V operating voltage, and a 16-pin TSSOP surface-mount package. The extended -55 °C to 125 °C temperature range supports industrial, instrumentation, telecommunications, and test-equipment environments. The package also offers a compact surface-mount footprint for designs that cannot accommodate a through-hole or larger-outline package.
The CD4051 uses three select inputs to address one of eight internal channels. Its enable input provides common control of the analog switch, allowing the device to be placed in a disabled state when no signal path is required. The address and enable logic operate from the device supply, making system-level design important: control levels, input signal range, and the common-terminal voltage must remain within the operating limits described by the manufacturer datasheet.
Typical uses include data acquisition, sensor-channel selection, analog signal routing, instrumentation, telecommunications, and embedded control systems. It can also function as a demultiplexer when a selected source is distributed through the common terminal. Because the selected path has finite resistance and coupling characteristics, high-speed or low-noise designs should account for on-state resistance, off-state leakage, charge injection, and switching transients.
For layout, place input and output routing so the selected analog path remains short and symmetric. Decoupling capacitors should be connected close to the supply and ground pins, while the address and enable traces should be kept away from sensitive analog nets. The supply must support the full signal range present at the analog terminals, and unused inputs should be tied to defined levels rather than left floating.
This page combines the manufacturer’s part classification, package and temperature information with engineering-focused routing, layout, comparison, and replacement guidance. It also identifies practical limits and qualification questions that should be checked before assigning the CD4051BPW to a new analog switching design.
Alternativas directas para CD4051BPW — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con CD4051BPW (mismo factor de forma y huella) — difiere en Package.
CD4051BQPWRQ1
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SN74HC4051PW
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
74HC4051PW
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TMUX1308
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TMUX7208
✅ Sustitución directaConsulte el precio
Ver hoja de datos →CD4051BPW Valores máximos y características eléctricas
| Product Type | 8:1 CMOS analog multiplexer or demultiplexer |
| Maximum Supply Voltage | 20 V |
| Multiplex Configuration | 8:1 |
| Number of Switched Channels | 1 channel |
| Logic-Level Conversion | Supported |
| Encapsulado | 16-pin TSSOP (PW) |
| Tipo de montaje | Surface mount |
| Minimum Operating Temperature | -55 °C |
| Maximum Operating Temperature | 125 °C |
| On-State Resistance | 240 ohm |
| Number of Select Inputs | 3 inputs |
Guía de configuración de pines de CD4051BPW 16-pin tssop (pw)
Configuración de pines para CD4051BPW (encapsulado 16-pin tssop (pw)). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para CD4051BPW.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
CD4051BPW es adecuado para 6 aplicacións: Multichannel Sensor Acquisition, Data Acquisition Front Ends, Laboratory Signal Routing, Telecommunications Signal Multiplexing, Industrial Control Signal Selection, Legacy Peripheral Signal Routing.
Multichannel Sensor Acquisition
The CD4051BPW fits sensor-acquisition systems that must connect one analog measurement path to several sensors or conditioning stages. Its three select inputs can address eight channels, while the 240 ohm listed on-state resistance is suitable for many moderate-impedance sensor circuits. The 20 V maximum supply rating also accommodates legacy industrial interfaces. Place the multiplexer close to the sensor inputs, keep the common-terminal route compact, and verify that input bias current, leakage, settling time, and measurement accuracy meet the sensor’s requirements.
Recomendado
Data Acquisition Front Ends
The CD4051BPW can route a selected source into a shared data-acquisition front end when a system must scan multiple analog inputs without using a separate converter channel for every signal. Its 8:1 configuration reduces routing complexity, and the -55 °C to 125 °C operating range supports industrial equipment. The main design trade-off is the 240 ohm on-state resistance, which can create signal attenuation with a high-impedance source. Confirm source impedance, acquisition time, injected charge, and leakage before using the mux in front of a high-resolution converter.
Recomendado
Laboratory Signal Routing
The CD4051BPW is useful in laboratory and test systems that route one instrument channel among several test points or stimulus sources. Its three binary address inputs provide deterministic channel selection, while enable control permits the selected path to be disconnected when appropriate. The 16-pin TSSOP package simplifies compact instrument boards. For low-level measurements, however, the listed 240 ohm path resistance and off-state leakage may limit accuracy. Use short PCB routes, guard sensitive nodes from select-line coupling, and evaluate the complete signal path before expecting precision low-noise performance.
Recomendado
Telecommunications Signal Multiplexing
The CD4051BPW can select or distribute analog paths in telecommunications and interface equipment where several legacy channels must share a common signal route. Its 20 V maximum supply voltage supports higher-voltage interfaces compared with 5 V HC-family devices, while the extended temperature range covers demanding industrial environments. Because the switch resistance and leakage affect channel insertion loss and crosstalk, keep the selected path short and ensure the enable and address pins do not inject transients into sensitive lines. Validate channel isolation against the system’s crosstalk requirement.
Recomendado
Industrial Control Signal Selection
The CD4051BPW fits industrial control boards that need to select among command, feedback, or reference signals using digital address logic. Its logic-level conversion can assist interface design, and the -55 °C to 125 °C rating supports harsh temperature conditions. The enable input allows the switch network to be disabled during unused intervals. Because 20 V is the maximum supply rating rather than a guaranteed operating point for every analog signal, verify input and common-terminal limits, transient protection, and grounding. Use a defined state for every control input during reset and power-up.
Recomendado
Legacy Peripheral Signal Routing
The CD4051BPW is appropriate for repairing or modernizing legacy peripheral boards that use a CD4000-style 8:1 analog routing function. The 20 V capability is important when an older circuit operates above the 6 V limits of many HC alternatives. A CD4051BQPWRQ1 offers the same footprint with automotive qualification, while other HC-family devices provide lower-voltage alternatives. Before replacing an installed device, compare the complete pin description and account for differences in logic thresholds, leakage, switch resistance, and power behavior rather than relying on the eight-channel function alone.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para CD4051BPW — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | CD4051BQPWRQ1 | SN74HC4051PW | 74HC4051PW | TMUX1308 | TMUX7208 |
|---|---|---|---|---|---|---|
| Package | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP | Texas Instruments | Texas Instruments |
| Multiplex Configuration | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 |
| Number of Switched Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Select Input Count | 3 inputs | 3 inputs | 3 inputs | 3 inputs | 3 inputs | 3 inputs |
Diferenciadores clave
- Supports higher-voltage systems than HC-family alternatives (frente a 74HC4051PW)
- Offers an automotive-qualified same-family option (frente a CD4051BQPWRQ1)
- Maintains the established CD4000 multiplexing architecture (frente a TMUX7208)
Notas de diseño
Route the common terminal and the selected channel directly to the intended signal destination with short traces and a continuous ground reference. Keep the three select inputs and enable control away from high-impedance analog nodes to reduce crosstalk through capacitive coupling. Place the supply-decoupling capacitor adjacent to the supply and ground pins, and use the manufacturer pin-description table to confirm orientation before assigning tracks.
Account for the listed 240 ohm on-state resistance when the source impedance is high. Estimated insertion loss can be calculated as 20·log10[(Rsource + 240 ohm)/(Rsource + 240 ohm + RL)], using the actual source impedance and load impedance. Include off-state leakage and injected charge when evaluating low-level or high-speed measurements, and verify settling time rather than assuming channel changes occur instantaneously.
Do not treat the 20 V maximum supply rating as permission to apply 20 V to every analog or control terminal. Check the complete absolute-maximum and recommended-operation tables, especially common-terminal voltage, select-input thresholds, and enable levels. Drive address and enable inputs with defined levels during reset and power-up, and confirm that the external circuit cannot back-power the device through the analog pins.
Información de cumplimiento
The CD4051BPW manufacturer product page and distributor classifications do not state the requested compliance statuses. The CD4051BQPWRQ1 alternative is identified as automotive, but the standard CD4051BPW qualification status remains unconfirmed.