CD4051BPW - 20V 8:1 CMOS Analog Multiplexer | Texas Instruments
부품 번호: CD4051BPW ✓ 활성CD4051BPW 개요
An analog multiplexer is a semiconductor switch that connects one common terminal to one of several channel terminals according to binary control signals. The CD4051 belongs to the CD4000 CMOS logic family, combining analog signal switching with digital address control. Its broad supply-voltage range supports legacy and industrial systems, while logic-level conversion helps the address interface operate reliably when the control logic uses a lower voltage than the analog supply.
Key features include an 8:1 multiplexing configuration, a maximum 20 V operating voltage, and a 16-pin TSSOP surface-mount package. The extended -55 °C to 125 °C temperature range supports industrial, instrumentation, telecommunications, and test-equipment environments. The package also offers a compact surface-mount footprint for designs that cannot accommodate a through-hole or larger-outline package.
The CD4051 uses three select inputs to address one of eight internal channels. Its enable input provides common control of the analog switch, allowing the device to be placed in a disabled state when no signal path is required. The address and enable logic operate from the device supply, making system-level design important: control levels, input signal range, and the common-terminal voltage must remain within the operating limits described by the manufacturer datasheet.
Typical uses include data acquisition, sensor-channel selection, analog signal routing, instrumentation, telecommunications, and embedded control systems. It can also function as a demultiplexer when a selected source is distributed through the common terminal. Because the selected path has finite resistance and coupling characteristics, high-speed or low-noise designs should account for on-state resistance, off-state leakage, charge injection, and switching transients.
For layout, place input and output routing so the selected analog path remains short and symmetric. Decoupling capacitors should be connected close to the supply and ground pins, while the address and enable traces should be kept away from sensitive analog nets. The supply must support the full signal range present at the analog terminals, and unused inputs should be tied to defined levels rather than left floating.
This page combines the manufacturer’s part classification, package and temperature information with engineering-focused routing, layout, comparison, and replacement guidance. It also identifies practical limits and qualification questions that should be checked before assigning the CD4051BPW to a new analog switching design.
드롭인 대체품: CD4051BPW — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: CD4051BPW (동일 폼 팩터 및 풋프린트) — 차이점: Package.
CD4051BQPWRQ1
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
SN74HC4051PW
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
74HC4051PW
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TMUX1308
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TMUX7208
✅ 드롭인가격 문의
데이터시트 보기 →CD4051BPW 최대 정격 & 전기적 특성
| Product Type | 8:1 CMOS analog multiplexer or demultiplexer |
| Maximum Supply Voltage | 20 V |
| Multiplex Configuration | 8:1 |
| Number of Switched Channels | 1 channel |
| Logic-Level Conversion | Supported |
| 패키지 | 16-pin TSSOP (PW) |
| 실장 유형 | Surface mount |
| Minimum Operating Temperature | -55 °C |
| Maximum Operating Temperature | 125 °C |
| On-State Resistance | 240 ohm |
| Number of Select Inputs | 3 inputs |
CD4051BPW 16-pin tssop (pw) 핀 구성 가이드
CD4051BPW(16-pin tssop (pw) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: CD4051BPW.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
CD4051BPW 적합 용도: 6 애플리케이션s: Multichannel Sensor Acquisition, Data Acquisition Front Ends, Laboratory Signal Routing, Telecommunications Signal Multiplexing, Industrial Control Signal Selection, Legacy Peripheral Signal Routing.
Multichannel Sensor Acquisition
The CD4051BPW fits sensor-acquisition systems that must connect one analog measurement path to several sensors or conditioning stages. Its three select inputs can address eight channels, while the 240 ohm listed on-state resistance is suitable for many moderate-impedance sensor circuits. The 20 V maximum supply rating also accommodates legacy industrial interfaces. Place the multiplexer close to the sensor inputs, keep the common-terminal route compact, and verify that input bias current, leakage, settling time, and measurement accuracy meet the sensor’s requirements.
추천
Data Acquisition Front Ends
The CD4051BPW can route a selected source into a shared data-acquisition front end when a system must scan multiple analog inputs without using a separate converter channel for every signal. Its 8:1 configuration reduces routing complexity, and the -55 °C to 125 °C operating range supports industrial equipment. The main design trade-off is the 240 ohm on-state resistance, which can create signal attenuation with a high-impedance source. Confirm source impedance, acquisition time, injected charge, and leakage before using the mux in front of a high-resolution converter.
추천
Laboratory Signal Routing
The CD4051BPW is useful in laboratory and test systems that route one instrument channel among several test points or stimulus sources. Its three binary address inputs provide deterministic channel selection, while enable control permits the selected path to be disconnected when appropriate. The 16-pin TSSOP package simplifies compact instrument boards. For low-level measurements, however, the listed 240 ohm path resistance and off-state leakage may limit accuracy. Use short PCB routes, guard sensitive nodes from select-line coupling, and evaluate the complete signal path before expecting precision low-noise performance.
추천
Telecommunications Signal Multiplexing
The CD4051BPW can select or distribute analog paths in telecommunications and interface equipment where several legacy channels must share a common signal route. Its 20 V maximum supply voltage supports higher-voltage interfaces compared with 5 V HC-family devices, while the extended temperature range covers demanding industrial environments. Because the switch resistance and leakage affect channel insertion loss and crosstalk, keep the selected path short and ensure the enable and address pins do not inject transients into sensitive lines. Validate channel isolation against the system’s crosstalk requirement.
추천
Industrial Control Signal Selection
The CD4051BPW fits industrial control boards that need to select among command, feedback, or reference signals using digital address logic. Its logic-level conversion can assist interface design, and the -55 °C to 125 °C rating supports harsh temperature conditions. The enable input allows the switch network to be disabled during unused intervals. Because 20 V is the maximum supply rating rather than a guaranteed operating point for every analog signal, verify input and common-terminal limits, transient protection, and grounding. Use a defined state for every control input during reset and power-up.
추천
Legacy Peripheral Signal Routing
The CD4051BPW is appropriate for repairing or modernizing legacy peripheral boards that use a CD4000-style 8:1 analog routing function. The 20 V capability is important when an older circuit operates above the 6 V limits of many HC alternatives. A CD4051BQPWRQ1 offers the same footprint with automotive qualification, while other HC-family devices provide lower-voltage alternatives. Before replacing an installed device, compare the complete pin description and account for differences in logic thresholds, leakage, switch resistance, and power behavior rather than relying on the eight-channel function alone.
추천
추천 제품 요약
엔지니어링 참조 데이터: CD4051BPW — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | CD4051BQPWRQ1 | SN74HC4051PW | 74HC4051PW | TMUX1308 | TMUX7208 |
|---|---|---|---|---|---|---|
| Package | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP | Texas Instruments | Texas Instruments |
| Multiplex Configuration | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 |
| Number of Switched Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Select Input Count | 3 inputs | 3 inputs | 3 inputs | 3 inputs | 3 inputs | 3 inputs |
주요 차별점
- Supports higher-voltage systems than HC-family alternatives (vs 74HC4051PW)
- Offers an automotive-qualified same-family option (vs CD4051BQPWRQ1)
- Maintains the established CD4000 multiplexing architecture (vs TMUX7208)
설계 노트
Route the common terminal and the selected channel directly to the intended signal destination with short traces and a continuous ground reference. Keep the three select inputs and enable control away from high-impedance analog nodes to reduce crosstalk through capacitive coupling. Place the supply-decoupling capacitor adjacent to the supply and ground pins, and use the manufacturer pin-description table to confirm orientation before assigning tracks.
Account for the listed 240 ohm on-state resistance when the source impedance is high. Estimated insertion loss can be calculated as 20·log10[(Rsource + 240 ohm)/(Rsource + 240 ohm + RL)], using the actual source impedance and load impedance. Include off-state leakage and injected charge when evaluating low-level or high-speed measurements, and verify settling time rather than assuming channel changes occur instantaneously.
Do not treat the 20 V maximum supply rating as permission to apply 20 V to every analog or control terminal. Check the complete absolute-maximum and recommended-operation tables, especially common-terminal voltage, select-input thresholds, and enable levels. Drive address and enable inputs with defined levels during reset and power-up, and confirm that the external circuit cannot back-power the device through the analog pins.
규정 준수 정보
The CD4051BPW manufacturer product page and distributor classifications do not state the requested compliance statuses. The CD4051BQPWRQ1 alternative is identified as automotive, but the standard CD4051BPW qualification status remains unconfirmed.