CD4051BPW - 20V 8:1 CMOS Analog Multiplexer | Texas Instruments
部品番号: CD4051BPW ✓ 生産中CD4051BPW 概要
An analog multiplexer is a semiconductor switch that connects one common terminal to one of several channel terminals according to binary control signals. The CD4051 belongs to the CD4000 CMOS logic family, combining analog signal switching with digital address control. Its broad supply-voltage range supports legacy and industrial systems, while logic-level conversion helps the address interface operate reliably when the control logic uses a lower voltage than the analog supply.
Key features include an 8:1 multiplexing configuration, a maximum 20 V operating voltage, and a 16-pin TSSOP surface-mount package. The extended -55 °C to 125 °C temperature range supports industrial, instrumentation, telecommunications, and test-equipment environments. The package also offers a compact surface-mount footprint for designs that cannot accommodate a through-hole or larger-outline package.
The CD4051 uses three select inputs to address one of eight internal channels. Its enable input provides common control of the analog switch, allowing the device to be placed in a disabled state when no signal path is required. The address and enable logic operate from the device supply, making system-level design important: control levels, input signal range, and the common-terminal voltage must remain within the operating limits described by the manufacturer datasheet.
Typical uses include data acquisition, sensor-channel selection, analog signal routing, instrumentation, telecommunications, and embedded control systems. It can also function as a demultiplexer when a selected source is distributed through the common terminal. Because the selected path has finite resistance and coupling characteristics, high-speed or low-noise designs should account for on-state resistance, off-state leakage, charge injection, and switching transients.
For layout, place input and output routing so the selected analog path remains short and symmetric. Decoupling capacitors should be connected close to the supply and ground pins, while the address and enable traces should be kept away from sensitive analog nets. The supply must support the full signal range present at the analog terminals, and unused inputs should be tied to defined levels rather than left floating.
This page combines the manufacturer’s part classification, package and temperature information with engineering-focused routing, layout, comparison, and replacement guidance. It also identifies practical limits and qualification questions that should be checked before assigning the CD4051BPW to a new analog switching design.
ドロップイン代替品: CD4051BPW — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: CD4051BPW (同一形状・フットプリント) — 相違点: Package.
CD4051BQPWRQ1
✅ ドロップイン📋 参考代替品(カタログ未掲載)
SN74HC4051PW
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
74HC4051PW
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TMUX1308
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TMUX7208
✅ ドロップイン価格はお問い合わせください
データシートを見る →CD4051BPW 最大定格&電気的特性
| Product Type | 8:1 CMOS analog multiplexer or demultiplexer |
| Maximum Supply Voltage | 20 V |
| Multiplex Configuration | 8:1 |
| Number of Switched Channels | 1 channel |
| Logic-Level Conversion | Supported |
| パッケージ | 16-pin TSSOP (PW) |
| 実装タイプ | Surface mount |
| Minimum Operating Temperature | -55 °C |
| Maximum Operating Temperature | 125 °C |
| On-State Resistance | 240 ohm |
| Number of Select Inputs | 3 inputs |
CD4051BPW 16-pin tssop (pw) ピン配置ガイド
CD4051BPW (16-pin tssop (pw) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: CD4051BPW.
詳細は データシート をご参照ください。
主な用途
CD4051BPW の用途: 6 件s: Multichannel Sensor Acquisition, Data Acquisition Front Ends, Laboratory Signal Routing, Telecommunications Signal Multiplexing, Industrial Control Signal Selection, Legacy Peripheral Signal Routing.
Multichannel Sensor Acquisition
The CD4051BPW fits sensor-acquisition systems that must connect one analog measurement path to several sensors or conditioning stages. Its three select inputs can address eight channels, while the 240 ohm listed on-state resistance is suitable for many moderate-impedance sensor circuits. The 20 V maximum supply rating also accommodates legacy industrial interfaces. Place the multiplexer close to the sensor inputs, keep the common-terminal route compact, and verify that input bias current, leakage, settling time, and measurement accuracy meet the sensor’s requirements.
おすすめ
Data Acquisition Front Ends
The CD4051BPW can route a selected source into a shared data-acquisition front end when a system must scan multiple analog inputs without using a separate converter channel for every signal. Its 8:1 configuration reduces routing complexity, and the -55 °C to 125 °C operating range supports industrial equipment. The main design trade-off is the 240 ohm on-state resistance, which can create signal attenuation with a high-impedance source. Confirm source impedance, acquisition time, injected charge, and leakage before using the mux in front of a high-resolution converter.
おすすめ
Laboratory Signal Routing
The CD4051BPW is useful in laboratory and test systems that route one instrument channel among several test points or stimulus sources. Its three binary address inputs provide deterministic channel selection, while enable control permits the selected path to be disconnected when appropriate. The 16-pin TSSOP package simplifies compact instrument boards. For low-level measurements, however, the listed 240 ohm path resistance and off-state leakage may limit accuracy. Use short PCB routes, guard sensitive nodes from select-line coupling, and evaluate the complete signal path before expecting precision low-noise performance.
おすすめ
Telecommunications Signal Multiplexing
The CD4051BPW can select or distribute analog paths in telecommunications and interface equipment where several legacy channels must share a common signal route. Its 20 V maximum supply voltage supports higher-voltage interfaces compared with 5 V HC-family devices, while the extended temperature range covers demanding industrial environments. Because the switch resistance and leakage affect channel insertion loss and crosstalk, keep the selected path short and ensure the enable and address pins do not inject transients into sensitive lines. Validate channel isolation against the system’s crosstalk requirement.
おすすめ
Industrial Control Signal Selection
The CD4051BPW fits industrial control boards that need to select among command, feedback, or reference signals using digital address logic. Its logic-level conversion can assist interface design, and the -55 °C to 125 °C rating supports harsh temperature conditions. The enable input allows the switch network to be disabled during unused intervals. Because 20 V is the maximum supply rating rather than a guaranteed operating point for every analog signal, verify input and common-terminal limits, transient protection, and grounding. Use a defined state for every control input during reset and power-up.
おすすめ
Legacy Peripheral Signal Routing
The CD4051BPW is appropriate for repairing or modernizing legacy peripheral boards that use a CD4000-style 8:1 analog routing function. The 20 V capability is important when an older circuit operates above the 6 V limits of many HC alternatives. A CD4051BQPWRQ1 offers the same footprint with automotive qualification, while other HC-family devices provide lower-voltage alternatives. Before replacing an installed device, compare the complete pin description and account for differences in logic thresholds, leakage, switch resistance, and power behavior rather than relying on the eight-channel function alone.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CD4051BPW — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | CD4051BQPWRQ1 | SN74HC4051PW | 74HC4051PW | TMUX1308 | TMUX7208 |
|---|---|---|---|---|---|---|
| Package | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) | TSSOP-16 (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP | Texas Instruments | Texas Instruments |
| Multiplex Configuration | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 |
| Number of Switched Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Select Input Count | 3 inputs | 3 inputs | 3 inputs | 3 inputs | 3 inputs | 3 inputs |
主な差別化要因
- Supports higher-voltage systems than HC-family alternatives (vs 74HC4051PW)
- Offers an automotive-qualified same-family option (vs CD4051BQPWRQ1)
- Maintains the established CD4000 multiplexing architecture (vs TMUX7208)
設計ノート
Route the common terminal and the selected channel directly to the intended signal destination with short traces and a continuous ground reference. Keep the three select inputs and enable control away from high-impedance analog nodes to reduce crosstalk through capacitive coupling. Place the supply-decoupling capacitor adjacent to the supply and ground pins, and use the manufacturer pin-description table to confirm orientation before assigning tracks.
Account for the listed 240 ohm on-state resistance when the source impedance is high. Estimated insertion loss can be calculated as 20·log10[(Rsource + 240 ohm)/(Rsource + 240 ohm + RL)], using the actual source impedance and load impedance. Include off-state leakage and injected charge when evaluating low-level or high-speed measurements, and verify settling time rather than assuming channel changes occur instantaneously.
Do not treat the 20 V maximum supply rating as permission to apply 20 V to every analog or control terminal. Check the complete absolute-maximum and recommended-operation tables, especially common-terminal voltage, select-input thresholds, and enable levels. Drive address and enable inputs with defined levels during reset and power-up, and confirm that the external circuit cannot back-power the device through the analog pins.
コンプライアンス情報
The CD4051BPW manufacturer product page and distributor classifications do not state the requested compliance statuses. The CD4051BQPWRQ1 alternative is identified as automotive, but the standard CD4051BPW qualification status remains unconfirmed.