INA101KUE4 - High-Accuracy Instrumentation Amplifier | TI
N.º de pieza: INA101KUE4 ✓ ActivoINA101KUE4 Descripción general
An instrumentation amplifier is a specialized amplifier that combines differential input, high input impedance, and precise gain-setting behavior in one integrated circuit. Its functional position is signal conditioning within the broader amplifier IC category: sensor output -> instrumentation amplifier -> ADC or signal-processing circuit. Unlike a general-purpose operational amplifier, an instrumentation amplifier is optimized for measuring small differential signals riding on a larger common-mode voltage, which helps preserve signal integrity in precision measurement systems.
The INA101KUE4 uses a three-amplifier architecture to provide high input impedance and accurate differential gain. Its stated bandwidth is 300 kHz, while the input offset voltage is 250 uV. The manufacturer describes the device as a high-accuracy instrumentation amplifier, and its single-ended amplifier output supports conversion of a differential input into a ground-referenced signal for downstream data conversion. An external resistor network sets the closed-loop gain according to the manufacturer's recommended circuit.
The main design trade-off is bandwidth versus precision. A 300 kHz bandwidth is suitable for many pressure, temperature, bridge-sensor, and general industrial measurement signals, but it is not intended for high-frequency waveform systems requiring megahertz-class signal bandwidth. Input common-mode range, output swing, supply voltage, and gain-error limits must be checked against the actual sensor output and the selected supply rails before the circuit is finalized.
Typical uses include low-level bridge and strain-gauge conditioning, medical sensor instrumentation, current-shunt measurement, precision current sensing, laboratory test equipment, and industrial process-control modules. In each case, the differential input architecture helps reject common-mode disturbance when the measured signal is small relative to the surrounding voltage range.
Place the gain-setting resistor directly at the amplifier pins and use a quiet reference or regulated supply for analog circuitry. Keep input and feedback traces short, use a solid ground plane, and decouple each supply rail close to the device. Check input and output common-mode limits across temperature, because operation near either range boundary can reduce usable signal swing even when the supply voltage itself is adequate.
This product page combines the INA101KUE4 device identity, verified package and performance details, sourcing information, replacement guidance, and practical circuit-design notes. It is intended to help engineers compare the exact INA101KUE4 ordering code against compatible alternatives while recognizing that instrumentation-amplifier pin compatibility must be confirmed at the individual-pin level.
Alternativas directas para INA101KUE4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con INA101KUE4 (mismo factor de forma y huella) — difiere en Package, Input Offset Voltage, Number of Circuits, Bandwidth, Gain Setting.
INA101KU
✅ Sustitución directaConsulte el precio
Ver hoja de datos →INA103KU
✅ Sustitución directaConsulte el precio
Ver hoja de datos →INA105KU/2K5
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
INA101KUE4 Valores máximos y características eléctricas
| Product Type | High-accuracy instrumentation amplifier |
| Number of Amplifiers | 3 internal amplifiers |
| Number of Circuits | 1 circuit |
| Input Offset Voltage | 250 uV |
| Bandwidth | 300 kHz |
| Tipo de salida | Single-ended |
| Encapsulado | 16-pin SOIC, 7.50 mm width |
| Terminal Count | 16 terminals |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Package Code | SOP |
| Estilo de montaje | Surface mount |
| Temperature Grade | Commercial |
Guía de configuración de pines de INA101KUE4 sop
Configuración de pines para INA101KUE4 (encapsulado sop). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para INA101KUE4.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
INA101KUE4 es adecuado para 6 aplicacións: Bridge and Strain-Gauge Measurement, Medical Sensor Instrumentation, Precision Current-Shunt Monitoring, Industrial Process-Control Sensing, Laboratory Measurement Equipment, Portable Battery-Powered Instrumentation.
Bridge and Strain-Gauge Measurement
The INA101KUE4 is well suited to low-level differential sensing from resistive bridges, strain gauges, and pressure elements because its instrumentation-amplifier architecture accepts a differential input while rejecting common-mode voltage. The 250 uV input offset specification is important when the bridge output is small, and the 300 kHz bandwidth is sufficient for many static and moderately dynamic mechanical measurements. Place the gain resistor close to the device, establish the sensor-return path cleanly, and verify that bridge excitation and signal common-mode voltage remain within the manufacturer limits.
Recomendado
Medical Sensor Instrumentation
The INA101KUE4 can condition low-amplitude differential signals from medical and biosensing front ends where preserving the sensor's small output is important. Its 250 uV input offset specification helps limit error relative to microvolt- and millivolt-level sensor outputs, while the 300 kHz bandwidth covers many physiological and diagnostic signals below that limit. Shield sensitive input traces, isolate digital clocks and switching regulators, and confirm suitability for the required medical-grade qualification and operating-temperature requirements.
Recomendado
Precision Current-Shunt Monitoring
The INA101KUE4 is appropriate for measuring the differential voltage generated across a current shunt in power supplies, motor controls, and battery systems. The differential input rejects the common-mode voltage present across a low-ohm shunt, while the instrumentation-amplifier configuration simplifies gain control. The 300 kHz bandwidth is useful for ripple and load-current analysis but does not extend to fast switching transients. Select a shunt resistance that keeps the signal within the input common-mode range and use Kelvin routing for best accuracy.
Recomendado
Industrial Process-Control Sensing
The INA101KUE4 can amplify differential outputs from industrial pressure, temperature, and level sensors before conversion by an ADC. Its 300 kHz bandwidth handles process-control signals without requiring a high-speed amplifier, and the three-amplifier architecture reduces the need for a carefully matched discrete gain stage. In factory equipment, maintain a separate analog ground return for the sensor and amplifier, keep relay and motor currents out of the reference path, and check transient protection at long cable interfaces.
Recomendado
Laboratory Measurement Equipment
The INA101KUE4 supports laboratory instruments that measure small differential voltages with high input impedance, including bench meters, programmable sources, and precision test fixtures. The 250 uV input offset specification helps establish accuracy for low-level measurements, while adjustable gain permits scaling for different transducer sensitivities. Place the gain resistor close to the IC, use short shielded input routing, decouple the supply rails locally, and account for output headroom when selecting the gain and operating voltage.
Recomendado
Portable Battery-Powered Instrumentation
The INA101KUE4 is suitable for portable measurement modules that must combine high input impedance with compact analog conditioning. Its 16-pin SOIC package supports conventional surface-mount assembly, and the 300 kHz bandwidth covers many sensor outputs without demanding a high-speed analog design. In a battery-powered system, confirm the supported supply range and supply current in the manufacturer datasheet, use a low-noise analog supply, and place bypass capacitors immediately across the supply pins to limit switching-induced noise.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para INA101KUE4 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | INA101KU | INA103KU | INA105KU/2K5 |
|---|---|---|---|---|
| Package | SOIC-16 | SOIC-14 | SOIC-16 | SOIC-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | High-accuracy instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier |
Diferenciadores clave
- Purpose-built differential signal conditioning (frente a LM2904PWR)
- Defined measurement bandwidth (frente a INA103KU)
- Single-ended precision output (frente a INA105KU/2K5)
Notas de diseño
Place the INA101KUE4 gain-setting resistor directly across the designated gain pins and keep the loop short to reduce parasitic resistance and noise pickup. Route differential inputs as a tightly matched pair and provide a continuous ground plane beneath the analog section. Avoid switching-regulator traces, relay-driver paths, and digital clock lines beneath the amplifier and feedback nodes.
Establish the common-mode and output-voltage budget before selecting the gain. The sensor or shunt must remain inside the amplifier's input common-mode range, and the required output must retain enough headroom below the positive supply rail. Estimated: for a gain of 100 and a 10 mV differential input, the ideal output is 1 V; add input-offset and gain-error effects when sizing the signal range.
Use separate local bypass capacitors from each supply pin to the ground plane and keep them close to the device. Confirm the supported supply range, supply-current behavior, and output-swing limits in the manufacturer datasheet before choosing rail voltages. For precision measurements, power the analog section from a low-noise source and prevent high-current returns from sharing the sensitive reference path.
Do not assume that every INA-family ordering code is board-compatible. INA101KU is identified as a 14-pin SOIC, while INA101KUE4 uses 16 pins. Before replacement, compare every named pin, the external gain-resistor connection, reference implementation, supply range, and output function. A matching package body alone does not establish pin-to-pin compatibility.
Información de cumplimiento
The commercial temperature grade is identified in the product listing. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product documentation.