INA110KU/1K - Fast-Settling FET-Input Amplifier | TI
N.º de pieza: INA110KU/1K ✓ ActivoINA110KU/1K Descripción general
An instrumentation amplifier is a precision analog signal-conditioning IC that combines a differential input stage, input amplifiers, and an output difference amplifier into one package. This integrated approach provides higher common-mode rejection and gain accuracy than a discrete op-amp network. The INA110 belongs to the broader hierarchy of operational amplifiers, instrumentation amplifiers, analog signal-conditioning ICs, and semiconductor devices used to convert low-level sensor outputs into measurable voltages.
The INA110 uses a current-feedback circuit topology with a laser-trimmed input stage. Its FET inputs support high input impedance and low bias current, while the internal gain-set resistors reduce the number of external precision components required. Internal gain selections of 1, 10, 100, 200, and 500 V/V cover common sensor ranges spanning millivolts to several volts. The 4-microsecond settling specification is particularly important when several sensors are scanned through a multiplexer and each channel must be measured quickly.
The device is intended for bridge, strain-gauge, pressure-transducer, current-shunt, biomedical, and general-purpose differential-signal measurement. Its input-stage architecture is suited to systems where signal common-mode voltage varies and accurate rejection of common-mode disturbance is required. Designers must also account for the finite gain-bandwidth product, input and output voltage limits, supply range, input bias current, and the settling behavior of the selected gain when operating at high acquisition rates.
The INA110KU/1K is appropriate for precision data acquisition, industrial measurement, portable instrumentation, sensor-interface modules, and laboratory signal conditioning. In multiplexed systems, its fast settling can reduce the dead time between sensor channels. In low-frequency measurement systems, the same integrated gain network can simplify calibration while preserving repeatable gain settings. The manufacturer identifies the INA110 as a high-speed gain block suitable for both dedicated analog front ends and multiplexed acquisition systems.
For PCB implementation, use the manufacturer pin-description table when assigning tracks and keep the input and output routing short to reduce parasitic pickup of high-impedance sensor signals. Place the power-supply bypass capacitor close to the supply pins, maintain a quiet return path, and avoid routing sensitive input nodes beside switching-converter traces or digital clock lines. Check the selected gain against the datasheet bandwidth and settling requirements rather than relying on small-signal bandwidth alone.
This product page consolidates the INA110 device function, gain options, settling behavior, package information, drop-in replacement assessment, comparison parameters, and practical layout guidance into a design-focused reference. The comparison also distinguishes exact family options from devices whose electrical functions are similar but whose pin compatibility requires separate verification.
Alternativas directas para INA110KU/1K — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con INA110KU/1K (mismo factor de forma y huella) — difiere en Package, Product Type, RoHS Status, Architecture, Gain-Bandwidth Product.
INA110KU
✅ Sustitución directaConsulte el precio
Ver hoja de datos →INA110KUG4
✅ Sustitución directaConsulte el precio
Ver hoja de datos →INA114BU
✅ Sustitución directaConsulte el precio
Ver hoja de datos →INA111BU
✅ Sustitución directaConsulte el precio
Ver hoja de datos →INA117KU
✅ Sustitución directaConsulte el precio
Ver hoja de datos →AD524ARZ-16
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
INA110KU/1K Valores máximos y características eléctricas
| Amplifier Type | Instrumentation amplifier |
| Number of Circuits | 1 circuit |
| Input Type | FET input |
| Topología | Current-feedback circuit topology |
| Internal Gain Settings | 1, 10, 100, 200, and 500 V/V |
| Settling Time to 0.01% | 4 us |
| Encapsulado | 16-SOIC |
| Terminal Count | 16 terminals |
| Tipo de montaje | Surface mount |
| Estado RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Guía de configuración de pines de INA110KU/1K 16-soic
Configuración de pines para INA110KU/1K (encapsulado 16-soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para INA110KU/1K.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
INA110KU/1K es adecuado para 6 aplicacións: Multiplexed Sensor Data Acquisition, Strain-Gauge Bridge Measurement, Pressure Transducer Interface, Portable Biomedical Instrumentation, Industrial Current-Shunt Monitoring, Laboratory Signal Conditioning.
Multiplexed Sensor Data Acquisition
The INA110KU/1K fits multiplexed sensor acquisition because its 4-microsecond settling to 0.01% shortens the interval needed after each input is selected. The amplifier can process the resulting differential sensor voltage while internal gains of 1, 10, 100, 200, or 500 V/V adapt the signal range for an ADC. Designers should include mux settling, source impedance, amplifier settling, and the converter acquisition window when calculating the complete cycle time. Keeping sensor traces short and bypassing the supply at the device also reduces errors that could otherwise be mistaken for slow channel settling.
Recomendado
Strain-Gauge Bridge Measurement
The INA110KU/1K is appropriate for differential bridge measurements where excitation produces a small millivolt-level signal and the common-mode voltage is much larger. Its FET-input architecture supports high input impedance, while internal gain settings up to 500 V/V can amplify the bridge difference without a discrete precision gain network. Gain selection must account for the corresponding bandwidth and settling behavior. Place the amplifier close to the bridge, maintain symmetrical input routing, and use a quiet ground reference to limit offset and common-mode errors in the measured strain signal.
Recomendado
Pressure Transducer Interface
The INA110KU/1K can condition the differential output of a resistive pressure bridge while rejecting excitation-related common-mode voltage. The internal gain choices allow a designer to select 10, 100, 200, or 500 V/V according to the transducer's full-scale output and required ADC range. Its fast 4-microsecond settling to 0.01% is useful in systems that scan several pressure channels. For reliable measurements, verify input and output swing limits, avoid clipping, and reference the ADC range to the selected gain so the full bridge output remains within the linear region.
Recomendado
Portable Biomedical Instrumentation
The INA110KU/1K is suitable for portable biomedical instrumentation when a low-level differential physiological signal must be amplified before digitization. FET inputs reduce loading on high-impedance sensors, and the internal gain network supports several signal ranges without a large external resistor array. The device's 4-microsecond settling also supports responsive acquisition of repeated or multiplexed channels. The circuit must still satisfy applicable medical-product safety and electromagnetic-compatibility requirements, and the sensor excitation, isolation strategy, leakage current, and electrode protection must be validated as a complete system.
Recomendado
Industrial Current-Shunt Monitoring
The INA110KU/1K can amplify the differential voltage generated across a current-shunt resistor when the shunt output lies within the amplifier's input range. Internal gain options let a single design cover signals from millivolts to substantially larger values, and fast settling supports rapid current measurements. Designers should choose the gain to keep the shunt voltage within the amplifier's linear input range while avoiding output saturation. A Kelvin connection from the shunt, short copper paths, and separation from high-current switching nodes are important for preserving measurement accuracy.
Recomendado
Laboratory Signal Conditioning
The INA110KU/1K is useful in laboratory instruments that must amplify a differential source while rejecting common-mode voltage and presenting a scaled signal to a converter or measurement instrument. The internal 1, 10, 100, 200, and 500 V/V gains provide repeatable range selection, while the fast settling response reduces dead time in automated test systems. For broadband laboratory signals, verify the gain-bandwidth product and output-drive limits for the selected gain. Use a shielded enclosure and guarded input routing when low-level signals would otherwise be affected by leakage, capacitance, or ambient interference.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para INA110KU/1K — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | INA110KU | INA110KUG4 | INA114BU | INA111BU | INA117KU | AD524ARZ-16 |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Function | Instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier | Instrumentation amplifier |
| Circuit Count | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
Diferenciadores clave
- Fast 0.01% settling supports high-speed acquisition (frente a INA114BU)
- Five integrated gain settings simplify range selection (frente a AD524ARZ-16)
- FET-input architecture supports high-impedance sensing (frente a INA111BU)
- Exact-family options simplify procurement continuity (frente a INA117KU)
Notas de diseño
Route the two differential inputs as a closely matched pair and keep them short, because unequal capacitance can create settling differences when a multiplexer or switched sensor is connected. Connect the instrumentation amplifier close to the source to minimize parasitic capacitance and pickup. Keep the input nodes away from power-switching traces, relay contacts, display circuitry, and digital clock lines. Use the manufacturer pin-description table when identifying the gain-control and feedback connections.
Place the required bypass capacitor immediately beside the INA110KU/1K supply pins and connect it to a low-impedance ground plane. Follow the datasheet capacitor value and voltage-rating requirements exactly. Check supply current under the selected gain and output-load condition, and confirm that the source can start and remain within its operating range during input-channel switching. Adequate local bypassing helps prevent supply disturbance from appearing as input-referred measurement error.
Validate acquisition timing with amplifier settling included rather than relying only on nominal bandwidth. The INA110KU/1K settles to 0.01% in 4 microseconds, but multiplexer transitions, source impedance, filter capacitors, and ADC sampling add their own settling requirements. Use the complete timing budget to define the sample-and-hold interval, and verify the selected gain against the gain-bandwidth product before promising accurate high-rate measurements.
Do not assume that two 16-SOIC instrumentation amplifiers are interchangeable solely because their packages match. Compare pin functions, gain-control logic, common-mode range, output swing, supply requirements, and external compensation components before substituting INA114BU, INA111BU, INA117KU, or AD524ARZ-16. For the exact INA110KU and INA110KUG4 ordering variants, verify grade and reel-packing details rather than relying only on the abbreviated MPN.
Información de cumplimiento
The accessible manufacturer product page identifies the INA110 family but does not state the exact material-compliance status of INA110KU/1K in the provided summary. Confirm current compliance records for the exact orderable part.