LM258DGKR - Dual 30V 700kHz Op Amp | Texas Instruments
N.º de pieza: LM258DGKR ✓ ActivoLM258DGKR Descripción general
An operational amplifier is an analog amplifier that uses high open-loop gain to amplify the difference between two input voltages. In the broader component hierarchy, an operational amplifier belongs to the amplifier IC and signal-conditioning categories. The LM258 combines two amplifiers in one package, allowing related measurements or control functions to share a common supply while reducing board area compared with two single amplifier packages.
Key characteristics include a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and typical input offset voltage of 300 µV. Its common-mode input range can extend to ground, which is useful when signals are referenced near the lower supply rail. The dual-channel configuration and 8-pin VSSOP package are particularly useful for industrial and embedded designs requiring two amplifier functions in a compact footprint.
The LM258 operates from a single supply or a split supply, allowing it to work with positive-only or bipolar rail arrangements. Its 700 kHz gain-bandwidth product is appropriate for general-purpose low-frequency signal paths rather than high-speed instrumentation. Designers should account for the -25°C to 85°C commercial temperature range when planning enclosure temperature, thermal rise, and production operating conditions.
Typical uses include pressure and temperature sensor conditioning, buffered control signals, low-side current measurement with a suitable sense amplifier, audio preamplification, and general industrial analog interfaces. The common-mode input capability near ground supports sensors whose output remains close to the lower rail, while the dual layout can simplify circuits requiring two closely related amplifier channels.
Design attention should focus on supply decoupling, output-load limits, input common-mode boundaries, and stability with capacitive loads. Place the supply bypass capacitor close to the device and check the datasheet's output-swing and capacitive-load recommendations before driving long capacitive cables or high-capacitance loads. Add input bias-current compensation when driving high-impedance sources.
This page consolidates the exact LM258DGKR ordering information, verified manufacturer characteristics, practical application guidance, and same-footprint replacement options. It also highlights where alternative amplifier families may change supply limits, temperature range, or common-mode behavior, helping engineers compare upgrades without relying on a simple function-name match.
Alternativas directas para LM258DGKR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LM258DGKR (mismo factor de forma y huella) — difiere en Common-Mode Input Range, Maximum Supply Voltage, Package.
LM258DGKRG4
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
LM358DGKR
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →LM358DGKRG4
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →LM2902DGKR
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
LM2902DGKRG4
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
LM258DGKR Valores máximos y características eléctricas
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 700 kHz |
| Rango de temperatura de funcionamiento | -25°C to 85°C |
| Typical Input Offset Voltage | 300 µV |
| Common-Mode Input Range | Can extend to ground |
| Supply Configuration | Single supply or split supply |
| Encapsulado | 8-pin VSSOP (DGK) |
| Package Width | 3.00 mm |
| Tipo de montaje | Surface mount |
| Número de pines | 8 pins |
| Differential Input Capability | High differential input voltage capability |
Guía de configuración de pines de LM258DGKR 3.00 mm
Configuración de pines para LM258DGKR (encapsulado 3.00 mm). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para LM258DGKR.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
LM258DGKR es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Temperature Measurement Front End, Power Supply Control and Monitoring, Audio Preamplification and Buffering, Low-Side Current Measurement, Embedded Analog Control Interface.
Industrial Sensor Signal Conditioning
The LM258DGKR fits low-frequency industrial sensor interfaces because its common-mode input range can extend to ground, allowing signals near the lower rail to be amplified without moving the source above ground. The dual configuration can process related sensor outputs or implement gain and filtering stages in one 8-pin VSSOP package. Its 700 kHz gain-bandwidth product provides useful bandwidth for common pressure, temperature, and resistive bridge conditioning, while the 30 V maximum supply supports higher-voltage industrial interfaces. Designers should confirm the actual input and output common-mode boundaries at the selected supply voltage and add input-bias compensation when the sensor source impedance is high.
Recomendado
Temperature Measurement Front End
The LM258DGKR can amplify and condition low-level temperature-sensor outputs in equipment where the signal is referenced close to ground. Its two channels allow one amplifier to provide gain while the other buffers a reference, drives an excitation signal, or monitors another related voltage. The 700 kHz gain-bandwidth product is more than adequate for typical thermal measurement bandwidths, and the compact VSSOP package saves board area in densely populated controllers. Accuracy depends on the sensor, resistor network, and offset behavior, so use the 300 µV typical input-offset specification as part of the error budget and verify the final operating point against the manufacturer limits.
Recomendado
Power Supply Control and Monitoring
The LM258DGKR is appropriate for slow supervisory loops that compare a feedback voltage against a reference and control an adjustment stage in a 30 V-class power supply. Its common-mode capability near ground is useful when the feedback node is close to the lower rail, and the dual arrangement can support both error amplification and a separate current or voltage monitoring function. The 700 kHz gain-bandwidth product suits loops with bandwidth well below 100 kHz, provided loop compensation accounts for the amplifier's actual gain, slew behavior, and load. Its -25°C to 85°C range also makes thermal margins an explicit part of the design review.
Recomendado
Audio Preamplification and Buffering
The LM258DGKR can provide modest audio gain, impedance buffering, or channel balancing in general-purpose audio modules. Its 700 kHz gain-bandwidth product supports low- and mid-frequency audio paths, and the two-channel package permits paired functions without using two separate ICs. The amplifier is not automatically suitable for every audio load: output swing, output-current capability, noise, and capacitive stability must be checked against the selected source and destination impedances. In a mixed-signal product, keep the return currents associated with the audio path separate from switching-supply and digital return currents to reduce audible noise coupling.
Recomendado
Low-Side Current Measurement
The LM258DGKR can amplify the small voltage produced by a low-side sense resistor when the measured current is referenced near ground. Its common-mode input range extending to ground is particularly useful for this topology, and the dual-channel arrangement can provide a second amplifier for filtering, offset correction, or output buffering. The 700 kHz gain-bandwidth product permits reasonable bandwidth for many current-control and battery-monitoring paths. The final error budget must include the 300 µV typical input offset, sense-resistor tolerance, amplifier noise, and any input-bias effects caused by the resistor network.
Recomendado
Embedded Analog Control Interface
The LM258DGKR is useful in embedded control boards that need two general-purpose analog channels for actuator control, analog monitoring, or bridging between a sensor and an ADC input. Its 8-pin VSSOP package reduces footprint compared with two separate single amplifiers, while the 30 V maximum supply rating supports interfaces above the usual low-voltage logic rails. The 700 kHz gain-bandwidth product suits slow control and monitoring signals rather than high-speed waveform processing. Place the bypass capacitor close to the supply pin, preserve a short ground return, and ensure the selected gain, load, and output-swing conditions remain within the manufacturer limits.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM258DGKR — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM258DGKRG4 | LM358DGKR | LM358DGKRG4 | LM2902DGKR | LM2902DGKRG4 |
|---|---|---|---|---|---|---|
| Package | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Green Ordering Suffix | No G4 suffix | G4 suffix | No G4 suffix | G4 suffix | No G4 suffix | G4 suffix |
Diferenciadores clave
- Exact LM258DGKR ordering option in the compact TI DGK footprint (frente a LM258DT)
- 30 V supply class with 700 kHz bandwidth (frente a LM2902DGKR)
- Dual general-purpose channels with near-ground common-mode input capability (frente a LM2904DGKR)
Notas de diseño
Confirm the minimum and maximum supply voltage for the selected operating condition in the manufacturer datasheet before using the 30 V headline rating. Place the bypass capacitor adjacent to the supply pin and connect it with a short return path to the device ground. This reduces supply-impedance feedback and helps prevent output disturbance when both amplifier channels switch load current.
Use the TI DGK land pattern rather than substituting a generic 8-pin SOIC footprint. The VSSOP body and lead spacing differ from SOIC dimensions, and pin numbering alone does not guarantee mechanical compatibility. Preserve a continuous ground plane beneath the device, keep sensitive input routes away from switching nodes, and place input and output resistors close to their associated amplifier pins.
Check input common-mode voltage, output swing, output-current capability, and capacitive-load stability at the actual supply voltage. The common-mode range extending to ground does not mean every signal near ground is valid at every supply voltage. Likewise, the 700 kHz gain-bandwidth product is not a guarantee of stable operation with arbitrary cable capacitance or large output loads; follow the manufacturer capacitive-load guidance.
Do not treat an eight-pin package match as sufficient proof of interchangeability. Before using LM358DGKR or LM2902DGKR in place of LM258DGKR, compare input bias current, quiescent current, output drive, common-mode limits, supply range, and stability. A production substitution should also receive a documented date-code and change-control review because family-specific electrical limits may differ.
Información de cumplimiento
The product page identifies the LM258 family as active. Specific RoHS, REACH, halogen-free, and conflict-minerals declarations for the exact LM258DGKR ordering code were not established and remain unknown.