Texas Instruments

LM258DGKR - Dual 30V 700kHz Op Amp | Texas Instruments

MPN: LM258DGKR ✓ فعال
30 V Vdss 8-pin VSSOP (DGK) Package
حداقل سفارش: 1 |

LM258DGKR نمای کلی

The Texas Instruments LM258DGKR is a dual, general-purpose operational amplifier rated for a 30 V supply, 700 kHz gain-bandwidth product, and operation from -25°C to 85°C. The device contains two amplifier channels in an 8-pin VSSOP (DGK) package, making it suitable for industrial signal conditioning, transducer interfaces, and general-purpose analog control circuits.

An operational amplifier is an analog amplifier that uses high open-loop gain to amplify the difference between two input voltages. In the broader component hierarchy, an operational amplifier belongs to the amplifier IC and signal-conditioning categories. The LM258 combines two amplifiers in one package, allowing related measurements or control functions to share a common supply while reducing board area compared with two single amplifier packages.

Key characteristics include a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and typical input offset voltage of 300 µV. Its common-mode input range can extend to ground, which is useful when signals are referenced near the lower supply rail. The dual-channel configuration and 8-pin VSSOP package are particularly useful for industrial and embedded designs requiring two amplifier functions in a compact footprint.

The LM258 operates from a single supply or a split supply, allowing it to work with positive-only or bipolar rail arrangements. Its 700 kHz gain-bandwidth product is appropriate for general-purpose low-frequency signal paths rather than high-speed instrumentation. Designers should account for the -25°C to 85°C commercial temperature range when planning enclosure temperature, thermal rise, and production operating conditions.

Typical uses include pressure and temperature sensor conditioning, buffered control signals, low-side current measurement with a suitable sense amplifier, audio preamplification, and general industrial analog interfaces. The common-mode input capability near ground supports sensors whose output remains close to the lower rail, while the dual layout can simplify circuits requiring two closely related amplifier channels.

Design attention should focus on supply decoupling, output-load limits, input common-mode boundaries, and stability with capacitive loads. Place the supply bypass capacitor close to the device and check the datasheet's output-swing and capacitive-load recommendations before driving long capacitive cables or high-capacitance loads. Add input bias-current compensation when driving high-impedance sources.

This page consolidates the exact LM258DGKR ordering information, verified manufacturer characteristics, practical application guidance, and same-footprint replacement options. It also highlights where alternative amplifier families may change supply limits, temperature range, or common-mode behavior, helping engineers compare upgrades without relying on a simple function-name match.

جایگزین‌های drop-in برای LM258DGKR — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای LM258DGKR (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Common-Mode Input Range, Maximum Supply Voltage, Package.

Texas Instruments
Common-Mode Input Range: Extends to ground
Maximum Supply Voltage: 36 V
Package: 8-pin VSSOP
مقایسه با LM258DGKR →

LM258DGKRG4

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-pin VSSOP (DGK)
Same DGK VSSOP footprint and LM258 family; green-compliant ordering suffix is the primary documented difference

📋 جایگزین مرجع (خارج از کاتالوگ)

LM358DGKR

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
Texas Instruments
📦 8-pin VSSOP (DGK)
2 channels · 36 V · 300 µV typical · Extends to ground · High; exact limit not stated · 8-pin VSSOP · Standard general-purpose dual operational amplifier · Surface mount

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

LM358DGKRG4

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
Texas Instruments
📦 8-pin VSSOP (DGK)
Dual general-purpose operational amplifier · 2 circuits · 700 kHz

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

LM2902DGKR

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-pin VSSOP (DGK)
Same DGK VSSOP footprint and dual layout, but the LM2902 is a lower-power family with different quiescent-current and load-performance limits

📋 جایگزین مرجع (خارج از کاتالوگ)

LM2902DGKRG4

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-pin VSSOP (DGK)
Same DGK VSSOP footprint and LM2902 family, with a green-compliance ordering suffix and lower-power family characteristics

📋 جایگزین مرجع (خارج از کاتالوگ)

LM258DGKR حداکثر مقادیر مجاز و مشخصات الکتریکی

Amplifier Type Dual general-purpose operational amplifier
Number of Channels 2 channels
Maximum Supply Voltage 30 V
Gain-Bandwidth Product 700 kHz
محدوده دمای کاری -25°C to 85°C
Typical Input Offset Voltage 300 µV
Common-Mode Input Range Can extend to ground
Supply Configuration Single supply or split supply
بسته‌بندی 8-pin VSSOP (DGK)
Package Width 3.00 mm
نوع نصب Surface mount
تعداد پین‌ها 8 pins
Differential Input Capability High differential input voltage capability

راهنمای پیکربندی پین LM258DGKR 3.00 mm

پیکربندی پین برای LM258DGKR (پکیج 3.00 mm). این قطعه آنالوگ دارای پین‌های ورودی، خروجی و تغذیه است. برای پیکربندی‌های پین offset null، جبران‌سازی و فعال‌سازی به دیتاشیت سازنده مراجعه کنید. ایده‌آل برای مدارهای شرطی‌سازی سیگنال و تقویت‌کننده.

نمودار پین‌آوت پکیج 3.00 mm برای LM258DGKR

داده پین‌آوت تفصیلی موجود نیست برای LM258DGKR.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

LM258DGKR مناسب است برای 6 کاربردs: Industrial Sensor Signal Conditioning, Temperature Measurement Front End, Power Supply Control and Monitoring, Audio Preamplification and Buffering, Low-Side Current Measurement, Embedded Analog Control Interface.

🏭

Industrial Sensor Signal Conditioning

The LM258DGKR fits low-frequency industrial sensor interfaces because its common-mode input range can extend to ground, allowing signals near the lower rail to be amplified without moving the source above ground. The dual configuration can process related sensor outputs or implement gain and filtering stages in one 8-pin VSSOP package. Its 700 kHz gain-bandwidth product provides useful bandwidth for common pressure, temperature, and resistive bridge conditioning, while the 30 V maximum supply supports higher-voltage industrial interfaces. Designers should confirm the actual input and output common-mode boundaries at the selected supply voltage and add input-bias compensation when the sensor source impedance is high.

🌡️

Temperature Measurement Front End

The LM258DGKR can amplify and condition low-level temperature-sensor outputs in equipment where the signal is referenced close to ground. Its two channels allow one amplifier to provide gain while the other buffers a reference, drives an excitation signal, or monitors another related voltage. The 700 kHz gain-bandwidth product is more than adequate for typical thermal measurement bandwidths, and the compact VSSOP package saves board area in densely populated controllers. Accuracy depends on the sensor, resistor network, and offset behavior, so use the 300 µV typical input-offset specification as part of the error budget and verify the final operating point against the manufacturer limits.

⚡

Power Supply Control and Monitoring

The LM258DGKR is appropriate for slow supervisory loops that compare a feedback voltage against a reference and control an adjustment stage in a 30 V-class power supply. Its common-mode capability near ground is useful when the feedback node is close to the lower rail, and the dual arrangement can support both error amplification and a separate current or voltage monitoring function. The 700 kHz gain-bandwidth product suits loops with bandwidth well below 100 kHz, provided loop compensation accounts for the amplifier's actual gain, slew behavior, and load. Its -25°C to 85°C range also makes thermal margins an explicit part of the design review.

🎧

Audio Preamplification and Buffering

The LM258DGKR can provide modest audio gain, impedance buffering, or channel balancing in general-purpose audio modules. Its 700 kHz gain-bandwidth product supports low- and mid-frequency audio paths, and the two-channel package permits paired functions without using two separate ICs. The amplifier is not automatically suitable for every audio load: output swing, output-current capability, noise, and capacitive stability must be checked against the selected source and destination impedances. In a mixed-signal product, keep the return currents associated with the audio path separate from switching-supply and digital return currents to reduce audible noise coupling.

🔋

Low-Side Current Measurement

The LM258DGKR can amplify the small voltage produced by a low-side sense resistor when the measured current is referenced near ground. Its common-mode input range extending to ground is particularly useful for this topology, and the dual-channel arrangement can provide a second amplifier for filtering, offset correction, or output buffering. The 700 kHz gain-bandwidth product permits reasonable bandwidth for many current-control and battery-monitoring paths. The final error budget must include the 300 µV typical input offset, sense-resistor tolerance, amplifier noise, and any input-bias effects caused by the resistor network.

🧩

Embedded Analog Control Interface

The LM258DGKR is useful in embedded control boards that need two general-purpose analog channels for actuator control, analog monitoring, or bridging between a sensor and an ADC input. Its 8-pin VSSOP package reduces footprint compared with two separate single amplifiers, while the 30 V maximum supply rating supports interfaces above the usual low-voltage logic rails. The 700 kHz gain-bandwidth product suits slow control and monitoring signals rather than high-speed waveform processing. Place the bypass capacitor close to the supply pin, preserve a short ground return, and ensure the selected gain, load, and output-swing conditions remain within the manufacturer limits.

خلاصه محصولات پیشنهادی

LM2902DGKR Same-footprint dual op amp for lower-power sensing designs استفاده‌شده در: Industrial Sensor Signal Conditioning, Power Supply Control and Monitoring, Low-Side Current Measurement LM358DGKR Texas Instruments استفاده‌شده در: Industrial Sensor Signal Conditioning, Temperature Measurement Front End, Audio Preamplification and Buffering, Embedded Analog Control Interface LM258DGKRG4 Same-package LM258 family ordering option استفاده‌شده در: Temperature Measurement Front End, Low-Side Current Measurement LM2902DGKRG4 Same-package lower-power family variant استفاده‌شده در: Power Supply Control and Monitoring LM358DGKRG4 Texas Instruments استفاده‌شده در: Audio Preamplification and Buffering, Embedded Analog Control Interface
What are the key specifications of LM258DGKR that engineers should know?
The LM258DGKR is a dual, general-purpose operational amplifier with a 30 V maximum supply, 700 kHz gain-bandwidth product, and a -25°C to 85°C operating range. It is offered in an 8-pin VSSOP (DGK) package, and each channel has a typical input offset voltage of 300 µV. According to the Texas Instruments LM258 datasheet, its common-mode input range can extend to ground, making it useful for low-level signals referenced near the lower supply rail.
Where can I download the LM258DGKR datasheet PDF?
The official LM258DGKR documentation is available through the Texas Instruments LM258 product page at https://www.ti.com/product/LM258. Open the product documentation area to access the manufacturer datasheet and then select the DGK ordering option for LM258DGKR. The manufacturer part-details page at https://www.ti.com/product/LM258/part-details/LM258DGKR identifies the device as an 8-pin VSSOP with eight pins and confirms the -25°C to 85°C operating range.
What is the LM258DGKR pinout and package footprint?
The LM258DGKR uses the TI DGK 8-pin VSSOP package, also identified by distributors as an 8-VSSOP or 8-MSOP package with a stated width of 3.00 mm. The exact numbered terminal assignments should be taken from the pin-description table in the Texas Instruments LM258 datasheet. The same DGK footprint must also be used when evaluating a substitute, because an 8-pin SOIC variant can require different board outlines and lead geometry.
Can LM258DGKR operate from a single 5 V supply?
The LM258 family supports single-supply and split-supply operation, but the exact minimum supply voltage must be checked in the manufacturer datasheet before finalizing a 5 V design. Its 30 V maximum supply rating does not mean every operating point below 30 V is supported. Confirm the minimum supply, common-mode range, output swing, and load current at the intended supply voltage, then include bypass capacitance close to the supply pins.
Is LM258DGKR suitable for sensor signal conditioning?
Yes, the LM258DGKR is suitable for many low-frequency sensor-conditioning applications because it provides two amplifiers, a 700 kHz gain-bandwidth product, and a common-mode input range that can extend to ground. These characteristics fit resistive, temperature, and pressure sensor interfaces whose outputs remain near the lower rail. High-impedance sources may require an input-bias-current compensation resistor, while gain and offset values should be selected against the amplifier's stated precision limits.
LM258DGKR vs LM258DT - which is better for a VSSOP PCB?
The LM258DGKR is the better choice when the existing PCB uses the TI DGK 8-pin VSSOP footprint because it is offered in that exact package. The LM258DT uses an 8-pin SOIC package, so it is not a same-footprint substitution even though both devices belong to the LM258 family and provide two amplifier channels. A board change, including lead spacing and land-pattern review, would be required when moving between DGK and SOIC packages.
When should I choose LM258DGKR over LM2902DGKR?
Choose LM258DGKR when the circuit is designed around the LM258 family's general-purpose performance and the required 30 V supply condition must remain within the LM258 operating limits. Choose LM2902DGKR when the lower-power LM2902 characteristics better match the design. Although both families use familiar dual operational-amplifier layouts and can share an 8-pin VSSOP outline, input bias, supply, speed, and output-current behavior should be compared directly before substitution.
Is LM258DGKR suitable for audio preamplification?
Yes, LM258DGKR can be used in general-purpose audio preamplifier and line-stage circuits when the signal bandwidth does not require a faster amplifier. Its 700 kHz gain-bandwidth product supports low- and mid-frequency audio signal paths, while the dual channel permits paired gain or buffering functions. Confirm output swing into the intended load, verify stability with the coupling network, and account for the device's input-offset and noise characteristics in high-gain stages.
What can replace LM258DGKR without changing the PCB?
A true PCB-compatible replacement must use the same TI DGK 8-pin VSSOP package, preserve the two-channel pin arrangement, and remain within acceptable supply, speed, input-offset, and common-mode limits. LM258DGKRG4 is a same-brand ordering option in the DGK package, while LM358DGKR and LM2902DGKR are possible same-footprint alternatives whose electrical characteristics require comparison. Review the manufacturer pin tables and operating limits before approving any substitution.
What is the best drop-in replacement for LM258DGKR?
The closest same-brand drop-in candidate is LM258DGKRG4 because it uses the same TI DGK 8-pin VSSOP package and the same LM258 family architecture. LM358DGKR and LM2902DGKR also use the DGK footprint but are not electrically identical, so they are suitable only when their supply, bias-current, common-mode, and output-drive characteristics meet the circuit requirements. No alternative should be approved solely from an eight-pin package match.
What is the best STMicroelectronics equivalent for LM258DGKR?
The STMicroelectronics LM258DT is functionally related to the LM258DGKR because both are dual operational amplifiers, but it is not a drop-in PCB replacement for a DGK VSSOP design. The LM258DT uses an 8-pin SOIC package with different body dimensions and lead spacing. Use it only after confirming whether the PCB can accommodate the SOIC land pattern or after redesigning the footprint and verifying every terminal assignment.
Where to buy LM258DGKR online?
Use the Request a Quote form on this page to request LM258DGKR availability, current lead time, and order handling. The exact MPN is a dual 30 V, 700 kHz operational amplifier in the 8-pin VSSOP (DGK) package. Before ordering, confirm the desired reel or tube packing configuration, quantity, operating-temperature marking, and any manufacturer-specific ordering requirements with the supplier.
What is the price of LM258DGKR?
Use the Request a Quote form on this page for the current LM258DG quotation and any available quantity breaks. Pricing depends on order quantity, package or carrier configuration, and market availability, so a static price can become stale quickly. The request can also confirm whether the exact DGK ordering code is available in the required production quantity and whether reels, tubes, or another approved packing format are needed.
What is the lead time for LM258DGKR?
Request the current lead time through the Request a Quote form on this page. Lead time can change with manufacturer inventory, order quantity, and packing choice, so it should be confirmed for the exact LM258DGKR ordering code rather than assumed from another LM258 variant. Include your forecast quantities, target date, and required tape-and-reel or tube format in the request.
Is LM258DGKR in stock and what is its lifecycle status?
The Texas Instruments LM258 family is presented as an active product family, but current LM258DGKR stock and production allocation should be confirmed through the Request a Quote form on this page. Provide the required quantity and packing format so the supplier can check the exact eight-pin DGK ordering option. For long-lived industrial equipment, also request lifecycle and change-control information appropriate to the intended qualification program.
How should LM258DGKR be decoupled and laid out for stable operation?
Place the supply bypass capacitor close to the LM258DGKR supply pin and route the return directly to the device ground pin to minimize loop area. Follow the manufacturer datasheet for recommended capacitance and decoupling details. In addition, keep sensitive input traces away from power and switching-node routes, provide a stable ground reference, and check output stability against the expected load and any capacitive loading introduced by cables or downstream circuits.

داده‌های مرجع مهندسی برای LM258DGKR — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose LM258DGKR when the PCB requires the TI DGK 8-pin VSSOP footprint and the circuit needs a dual general-purpose amplifier rated for a 30 V supply, 700 kHz bandwidth, and operation from -25°C to 85°C. LM258DGKRG4 is the closest same-family ordering option when its documented suffix and ordering conditions meet production requirements. Consider LM358DGKR when its LM358-family limits satisfy the design, but verify supply range, common-mode behavior, input bias, and output drive. Consider LM2902DGKR when lower power is more important than the LM258 family's performance. The STMicroelectronics LM258DT is functionally similar but uses an SOIC package, so it is not suitable for an unchanged VSSOP PCB. For every substitution, compare the manufacturer pin tables, full operating limits, stability requirements, and production change-control conditions.

مقایسه با جایگزین‌ها

پارامتر این محصول LM258DGKRG4 LM358DGKR LM358DGKRG4 LM2902DGKR LM2902DGKRG4
Package 8-pin VSSOP (DGK) 8-pin VSSOP (DGK) 8-pin VSSOP (DGK) 8-pin VSSOP (DGK) 8-pin VSSOP (DGK) 8-pin VSSOP (DGK)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Number of Channels 2 2 2 2 2 2
Green Ordering Suffix No G4 suffix G4 suffix No G4 suffix G4 suffix No G4 suffix G4 suffix

تفاوت‌های کلیدی

  • Exact LM258DGKR ordering option in the compact TI DGK footprint (در مقابلLM258DT)
  • 30 V supply class with 700 kHz bandwidth (در مقابلLM2902DGKR)
  • Dual general-purpose channels with near-ground common-mode input capability (در مقابلLM2904DGKR)

یادداشت‌های طراحی

Confirm the minimum and maximum supply voltage for the selected operating condition in the manufacturer datasheet before using the 30 V headline rating. Place the bypass capacitor adjacent to the supply pin and connect it with a short return path to the device ground. This reduces supply-impedance feedback and helps prevent output disturbance when both amplifier channels switch load current.

Use the TI DGK land pattern rather than substituting a generic 8-pin SOIC footprint. The VSSOP body and lead spacing differ from SOIC dimensions, and pin numbering alone does not guarantee mechanical compatibility. Preserve a continuous ground plane beneath the device, keep sensitive input routes away from switching nodes, and place input and output resistors close to their associated amplifier pins.

Check input common-mode voltage, output swing, output-current capability, and capacitive-load stability at the actual supply voltage. The common-mode range extending to ground does not mean every signal near ground is valid at every supply voltage. Likewise, the 700 kHz gain-bandwidth product is not a guarantee of stable operation with arbitrary cable capacitance or large output loads; follow the manufacturer capacitive-load guidance.

Do not treat an eight-pin package match as sufficient proof of interchangeability. Before using LM358DGKR or LM2902DGKR in place of LM258DGKR, compare input bias current, quiescent current, output drive, common-mode limits, supply range, and stability. A production substitution should also receive a documented date-code and change-control review because family-specific electrical limits may differ.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The product page identifies the LM258 family as active. Specific RoHS, REACH, halogen-free, and conflict-minerals declarations for the exact LM258DGKR ordering code were not established and remain unknown.

تاریخ تأیید داده‌ها: 2026-11-15 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

LM258DGKR datasheet LM258DGKR datasheet pdf LM258DGKR pinout LM258DGKR equivalent LM258DGKR replacement LM258DGKR cross reference LM258DGKR footprint LM258DGKR price LM258DGKR stock Texas Instruments LM258DGKR LM258DGKR vs LM258DT LM258DGKR application circuit

قطعات و اصطلاحات مرتبط

Texas Instruments LM258DGKR LM258 LM258DGKRG4 LM358DGKR LM358DGKRG4 LM2902DGKR LM2902DGKRG4 STMicroelectronics LM258DT dual operational amplifier general-purpose amplifier amplifier IC analog signal conditioning voltage-feedback operational amplifier common-mode input range gain-bandwidth product input offset voltage single-supply operation split-supply operation VSSOP-8 DGK package surface mount industrial sensor conditioning power supply control
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ