onsemi

LM2902DTBG - Quad 3-26V Op Amp, TSSOP-14 | onsemi

N.º de pieza: LM2902DTBG ✓ Activo
3 V to 26 V Vdss 14-pin TSSOP Package
MOQ: 1 |

LM2902DTBG Descripción general

The onsemi LM2902DTBG is a single-supply quad operational amplifier with four amplifiers, a 3 V to 26 V operating supply range, and a 14-pin TSSOP package. It supports true differential inputs and operation from -40 °C to +105 °C, making it suitable for general-purpose industrial signal-conditioning and control circuits.

An operational amplifier, or op amp, is a high-gain analog building block that compares two input voltages and drives an output to amplify the difference between them. The LM2902 belongs to the operational-amplifier hierarchy within analog and mixed-signal ICs. Its differential input architecture supports common signal-conditioning uses such as buffers, amplifiers, comparators, instrumentation stages, and active-feedback circuits.

The principal benefits of the LM2902DTBG are its four independent amplifier channels, single-supply operation from 3 V to 26 V, and low-power design characteristics. Four channels in one package can reduce board area in designs that need several matched general-purpose amplifiers. The broad 3 V to 26 V supply range also permits operation from conventional 5 V and 12 V rails as well as higher industrial supply levels that remain below the device rating.

The device is based on the established LM324-family architecture, which uses true differential inputs. According to onsemi documentation, the LM324 series is designed for low-cost, general-purpose applications and provides particular advantages in single-supply systems. A unity-gain bandwidth of approximately 1 MHz is suitable for audio-frequency, sensor-interface, feedback-control, and general analog-signal applications rather than high-speed precision instrumentation.

Typical uses include four-channel sensor conditioning, low-frequency active filters, audio preamplifier stages, comparator functions, industrial control loops, and general-purpose buffering. The four amplifiers can operate independently, although common power rails and package-level thermal behavior should be considered when all channels drive substantial loads.

For new layouts, use the manufacturer pin-description table when assigning PCB tracks and preserve the TSSOP-14 land pattern. Check input common-mode range, output swing, input bias current, noise, offset voltage, and slew rate against the actual signal amplitude and frequency before finalizing the circuit.

This page combines the LM2902DTBG operating limits, package information, replacement options, and practical circuit-placement guidance into an engineering-focused selection resource for buyers and designers evaluating quad single-supply op amps.

Alternativas directas para LM2902DTBG — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con LM2902DTBG (mismo factor de forma y huella) — difiere en Package, Gain-Bandwidth Product.

Texas Instruments
Package: 14-TSSOP (PW)
Gain-Bandwidth Product: 1 MHz
Texas Instruments
Package: 14-TSSOP
Gain-Bandwidth Product: 1.2 MHz
Comparar con LM2902DTBG →

LM2902PWRG4

✅ Sustitución directa
Texas Instruments
📦 14-pin TSSOP
Quad general-purpose operational amplifier · 4 circuits · 26 V · 1.2 MHz · 14-TSSOP · Surface mount · Single supply or dual supply

Consulte el precio

Ver hoja de datos →

LM2902DTBR2G

✅ Sustitución directa
onsemi
📦 14-pin TSSOP
General-purpose operational amplifier · 4 circuits · 1 MHz · 0.6 V/µs · 3 V · 32 V · 3 V to 26 V · True differential inputs

Consulte el precio

Ver hoja de datos →

NCV2902DTBR2G

✅ Sustitución directa
📦 14-pin TSSOP
Same 14-pin TSSOP footprint with 0 stated pin-layout differences; the NCV family designation indicates a distinct qualification-oriented device variant.

📋 Alternativa de referencia (no en el catálogo)

LM2902VDTBR2G

✅ Sustitución directa
onsemi
📦 14-pin TSSOP
Quad general-purpose operational amplifier · 4 circuits · 3 V to 26 V · Low-power · Extended temperature · True differential inputs · 14-TSSOP · Thin small-outline package

Consulte el precio

Ver hoja de datos →

LM2902KPWRG4

✅ Sustitución directa
📦 14-pin TSSOP
Same 14-pin TSSOP footprint with 0 stated pin-layout differences; the K-prefix ordering code identifies a distinct variant requiring electrical comparison.

📋 Alternativa de referencia (no en el catálogo)

LM2902DTBG Valores máximos y características eléctricas

Amplifier Count 4 amplifiers
Supply Voltage Range 3 V to 26 V
Rango de temperatura de funcionamiento -40 °C to +105 °C
Encapsulado 14-pin TSSOP
Tipo de montaje Surface mount
Product Category General-purpose operational amplifier
Supply Type Single supply
Input Architecture True differential input
Unity-Gain Bandwidth Approximately 1 MHz

Guía de configuración de pines de LM2902DTBG 14-pin tssop

Configuración de pines para LM2902DTBG (encapsulado 14-pin tssop). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 14-pin tssop para LM2902DTBG

No hay datos detallados de patillaje disponibles para LM2902DTBG.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

LM2902DTBG es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Audio Preamplifier Stages, Active Filters and Control Loops, Comparator and Threshold Detection, Portable and Battery-Powered Analog Circuits, Test and Measurement Front Ends.

🏭

Industrial Sensor Signal Conditioning

The LM2902DTBG fits four-channel industrial sensor conditioning because it combines four true-differential-input amplifiers with a 3 V to 26 V single-supply range. Engineers can use the channels for buffering, gain stages, active filtering, or level shifting around low-frequency sensor outputs. Its approximately 1 MHz unity-gain bandwidth is more than adequate for many pressure, temperature, and position signals. The -40 °C to +105 °C rating supports industrial environments, but each sensor interface must still be checked for input common-mode range, offset, bias current, and output-swing requirements.

🎧

Audio Preamplifier Stages

The LM2902DTBG can implement several low-frequency audio preamplifier or mixer channels within one 14-pin TSSOP package. Its four true-differential-input amplifiers are useful for source buffers, volume-control gain stages, and active balancing networks. The 3 V minimum supply supports portable equipment, while operation up to 26 V provides flexibility for higher-voltage analog systems. With approximately 1 MHz unity-gain bandwidth, the device is best suited to voice-band and conventional audio functions rather than high-frequency video or ultrasonic signal paths.

⚡

Active Filters and Control Loops

The LM2902DTBG is appropriate for active low-pass, high-pass, and feedback-control circuits where four general-purpose channels can reduce board area. Its 3 V to 26 V operating range permits implementation on 5 V or 12 V control rails, and the approximately 1 MHz unity-gain bandwidth is sufficient for many audio-band and slow industrial loops. When designing filters, account for resistor tolerances, amplifier offset, noise, output loading, and compensation requirements. The industrial temperature range of -40 °C to +105 °C helps maintain suitability across varied enclosure conditions.

🔧

Comparator and Threshold Detection

The LM2902DTBG can implement up to four independent comparator-style threshold detectors when the signal remains within the amplifier's common-mode and output-swing limits. The 3 V to 26 V supply range is useful for detecting sensor, battery, or divided-reference voltages in industrial systems. Because this is a general-purpose operational amplifier rather than a dedicated open-drain comparator, the output behavior, saturation recovery, input protection, and supply current must be reviewed for the specific application.

📱

Portable and Battery-Powered Analog Circuits

The LM2902DTBG is suitable for low-frequency analog sections in portable equipment because it supports single-supply operation starting at 3 V and contains four amplifier channels in one TSSOP package. Engineers can use the channels for microphone-style signal conditioning, sensor amplification, gain control, or voltage buffering around a low-voltage system rail. The low-power nature of the LM324 family helps conserve energy, although total current depends on the selected configuration and load. Confirm output load capability, shutdown strategy, and thermal behavior across the complete battery-discharge range.

🖥️

Test and Measurement Front Ends

The LM2902DTBG can provide buffering, gain, differential conversion, and active feedback for general-purpose test and measurement equipment. Four channels allow a compact instrument front end to support several probes or repeated measurement stages without using four separate packages. The 3 V to 26 V supply range supports portable and bench equipment, while the -40 °C to +105 °C rating covers extended industrial environments. Precision instrumentation still requires checking offset voltage, input bias current, noise, common-mode range, and stability for the selected gain and frequency.

What is the LM2902DTBG?
The LM2902DTBG is an onsemi quad operational amplifier that combines four general-purpose amplifiers in one 14-pin TSSOP package. According to onsemi LM2902 documentation, the LM324-family architecture uses true differential inputs and is intended for low-cost, single-supply applications. The device operates from 3 V to 26 V, making it suitable for conventional 5 V and 12 V industrial or instrumentation systems.
What is the operating voltage range of LM2902DTBG?
The LM2902DTBG operates from 3 V to 26 V. This single-supply range allows one amplifier family to serve 5 V, 12 V, and other compatible industrial rails. The onsemi LM2902 documentation identifies the LM324 series as useful in single-supply systems, while the listed temperature range is -40 °C to +105 °C. Designers should also verify signal input and output ranges against their operating rail.
What is the operating temperature range of LM2902DTBG?
The LM2902DTBG is rated for operation from -40 °C to +105 °C. This range covers industrial temperature environments where a standard commercial-temperature amplifier may be insufficient. According to the onsemi product information, the quad TSSOP device also supports a 3 V to 26 V supply range. Temperature qualification alone does not establish suitability for automotive or safety-critical applications.
Where can I download the LM2902DTBG datasheet PDF and find its pinout?
The LM2902DTBG datasheet and package documentation can be found through the linked onsemi datasheet resource, which provides electrical characteristics, application information, and the 14-pin TSSOP connection details. Use the manufacturer pin-description table when assigning PCB tracks because a 14-pin package designation alone does not identify each amplifier's input, output, supply, and no-connect positions.
Can LM2902DTBG be used as a drop-in replacement for LM324DTBG?
The LM2902DTBG can be considered for LM324DTBG positions only after confirming the complete pin configuration, supply limits, offset requirements, and temperature rating. The LM2902 and LM324 families share the familiar quad operational-amplifier architecture, but the onsemi ordering information must be checked for the exact package and suffix. A same-family designation alone does not waive application-level qualification.
Is LM2902DTBG suitable for single-supply sensor conditioning?
Yes, the LM2902DTBG is suitable for many single-supply sensor-conditioning circuits because it contains four true-differential-input amplifiers and operates from 3 V to 26 V. The approximately 1 MHz unity-gain bandwidth supports low-frequency instrumentation and control signals. Verify the sensor output range, required common-mode range, offset accuracy, and noise performance before using it for precision measurements.
What can replace the LM2902DTBG?
The LM2902DTBR2G, NCV2902DTBR2G, LM2902VDTBR2G, LM2902KPWRG4, and LM2902PWRG4 are candidate replacements associated with the onsemi LM2902 family and 14-pin TSSOP alternatives. Confirm the manufacturer pin table, electrical limits, qualification status, and temperature grade for each candidate before substitution. This page lists them as same-footprint engineering alternatives rather than automatic production approvals.
What is the best drop-in replacement for LM2902DTBG?
No single replacement can be selected unconditionally because the correct choice depends on the required temperature grade, qualification, offset performance, and production status. LM2902DTBR2G, NCV2902DTBR2G, LM2902VDTBR2G, LM2902KPWRG4, and LM2902PWRG4 provide candidate same-footprint choices within the onsemi LM2902 family. Compare their complete electrical tables and package drawings before releasing a substitution.
When should I choose LM2902DTBG over another LM2902 variant?
Choose LM2902DTBG when a design needs four general-purpose amplifiers, a 3 V to 26 V single supply, operation across -40 °C to +105 °C, and a 14-pin TSSOP footprint. Choose another LM2902 ordering option when a different temperature, qualification, or production requirement applies. For this family, compare the suffix-specific datasheet because ordering codes can encode meaningful electrical or qualification differences.
LM2902DTBG vs LM2902PWRG4 — which is better for industrial control?
The LM2902DTBG and LM2902PWRG4 are both associated with the onsemi quad LM2902 family and 14-pin TSSOP implementations, but the correct industrial choice depends on their suffix-specific temperature and qualification ratings. Both provide four single-supply amplifier channels, and the LM2902DTBG is specified for -40 °C to +105 °C. Verify the alternative's complete electrical table and lifecycle status before approval.
Is LM2902DTBG the same as LM2902DTBR2G?
The LM2902DTBG and LM2902DTBR2G belong to the same onsemi LM2902 family and are associated with the same 14-pin TSSOP package, but they are not necessarily identical in qualification or ordering characteristics. According to onsemi ordering information, suffix codes can identify different device variants. Confirm pinout, temperature grade, qualification, electrical limits, and lifecycle status before treating them as interchangeable.
What are the key specifications of LM2902DTBG that engineers should know?
The key LM2902DTBG specifications are four integrated operational-amplifier channels, a 3 V to 26 V supply range, a -40 °C to +105 °C operating range, true differential inputs, and a 14-pin TSSOP package. The unity-gain bandwidth is approximately 1 MHz. These parameters place the device in the general-purpose, low-frequency analog category rather than the high-speed or precision-amplifier category.
Where to buy LM2902DTBG online?
Use the Request a Quote form on this page to ask for LM2902DTBG availability, packaging, and a current quotation. The form gives you one direct channel for procurement without relying on static availability information. For production planning, confirm the exact onsemi ordering code, delivery quantity, and lifecycle status when the quotation is prepared.
What is the price of LM2902DTBG?
Use the Request a Quote form on this page for the current LM2902DTBG unit pricing and volume breaks. Market pricing can vary with order quantity, package readiness, and supply conditions, so a static figure may not represent the procurement requested. Include your required quantity, packaging preference, and target date in the request to obtain an actionable quotation.
What is the lead time for LM2902DTBG and is it in stock?
Request current LM2902DTBG stock, lead time, and minimum-order quantity through the Request a Quote form on this page. The part is represented by active distributor listings, but listing activity alone does not establish the quantity available for your order. Provide your production schedule and packaging requirements so the supplier can confirm allocation and delivery timing.

Datos de referencia de ingeniería para LM2902DTBG — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the LM2902DTBG when a design needs four general-purpose, true-differential-input amplifiers in a 14-pin TSSOP package, a 3 V to 26 V single supply, and operation from -40 °C to +105 °C. It is well suited to industrial sensor conditioning, active feedback, audio-band amplification, threshold detection, and general instrumentation. Consider LM2902PWRG4 or LM2902DTBR2G when their ordering-specific qualification or lifecycle characteristics better match the production program. NCV2902DTBR2G may be preferable for applications requiring a distinct qualification-oriented NCV-family option, while LM2902VDTBR2G and LM2902KPWRG4 cover other suffix-specific variants. Treat all five as candidate drop-in devices because they use the same 14-pin TSSOP footprint, but approve a substitution only after comparing the complete pin table, electrical limits, temperature rating, qualification status, and lifecycle information.

Comparación con alternativas

Parámetro Este producto LM2902PWRG4 LM2902DTBR2G NCV2902DTBR2G LM2902VDTBR2G LM2902KPWRG4
Package 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP
Brand onsemi onsemi onsemi onsemi onsemi onsemi
Amplifier Count 4 amplifiers 4 amplifiers 4 amplifiers 4 amplifiers 4 amplifiers 4 amplifiers
Input Architecture True differential input True differential input True differential input True differential input True differential input True differential input
Product Family LM2902 general-purpose quad operational amplifier LM2902 general-purpose quad operational amplifier LM2902 general-purpose quad operational amplifier NCV2902 quad operational amplifier LM2902 general-purpose quad operational amplifier LM2902 general-purpose quad operational amplifier

Diferenciadores clave

  • Combines four amplifier channels in one TSSOP package (frente a LM2902PWRG4)
  • Single-supply range supports multiple conventional rails (frente a LM2902DTBR2G)
  • Extended industrial temperature operation (frente a NCV2902DTBR2G)

Notas de diseño

Use the manufacturer pin-description table when routing the 14-pin TSSOP layout. Place each amplifier's supply bypass capacitor close to the appropriate power pin, and keep sensitive input and feedback traces short to reduce capacitive pickup. Because all four channels share package leads and thermal paths, avoid long parallel input routes where adjacent channels carry high-level signals. Confirm exposed-pad or thermal requirements against the exact package drawing before release.

Decouple the supply locally with ceramic capacitors selected from the manufacturer's recommended capacitance and voltage-rating guidance. The LM2902DTBG supports 3 V to 26 V operation, but decoupling requirements can vary with supply impedance, cable length, amplifier configuration, and output load. Check each channel's input and output voltage limits at the minimum and maximum local rail voltages; being within the absolute supply rating does not guarantee that every signal remains within the linear common-mode range.

Do not use the approximately 1 MHz unity-gain bandwidth as permission to design a unity-gain stage at 1 MHz. Op-amp stability depends on gain, noise gain, capacitive loading, output impedance, and the feedback network. Also verify input common-mode range, output swing, input offset, and load current. For comparator-style use, check saturation recovery and output behavior because the LM2902DTBG is a linear operational amplifier rather than a dedicated comparator.

Calculate worst-case dissipation from the actual output stage, output current, and voltage drop across the device rather than estimating from total supply current alone. Four active channels can increase package heating even when each amplifier individually carries a modest load. Use the package thermal information and PCB copper area to estimate junction temperature. Estimated: use the maximum expected supply voltage, output voltage, output current, and manufacturer power-dissipation equations for the operating environment.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were identified for the exact LM2902DTBG ordering code.

Datos verificados el: 2026-11-17 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

LM2902DTBG datasheet LM2902DTBG pinout LM2902DTBG datasheet pdf LM2902DTBG TSSOP-14 pinout onsemi LM2902DTBG LM2902DTBG 3-26V LM2902DTBG quad op amp LM2902DTBG drop-in replacement LM2902DTBG equivalent LM2902DTBG vs LM2902PWRG4 LM2902DTBG sensor conditioning LM2902DTBG active filter LM2902DTBG price LM2902DTBG stock LM2902DTBG schematic

Componentes & términos relacionados

onsemi LM2902DTBG LM2902PWRG4 LM2902DTBR2G NCV2902DTBR2G LM2902VDTBR2G LM2902KPWRG4 LM324 LM2902 operational amplifier op amp quad operational amplifier analog integrated circuit single-supply amplifier true differential input active filter sensor signal conditioning feedback control audio preamplifier instrumentation amplifier TSSOP-14 TSSOP package family surface-mount package 3 V to 26 V power supply -40 °C to +105 °C operating range
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ