LM2902DTBG - Quad 3-26V Op Amp, TSSOP-14 | onsemi
MPN: LM2902DTBG ✓ 啟用中LM2902DTBG 概覽
An operational amplifier, or op amp, is a high-gain analog building block that compares two input voltages and drives an output to amplify the difference between them. The LM2902 belongs to the operational-amplifier hierarchy within analog and mixed-signal ICs. Its differential input architecture supports common signal-conditioning uses such as buffers, amplifiers, comparators, instrumentation stages, and active-feedback circuits.
The principal benefits of the LM2902DTBG are its four independent amplifier channels, single-supply operation from 3 V to 26 V, and low-power design characteristics. Four channels in one package can reduce board area in designs that need several matched general-purpose amplifiers. The broad 3 V to 26 V supply range also permits operation from conventional 5 V and 12 V rails as well as higher industrial supply levels that remain below the device rating.
The device is based on the established LM324-family architecture, which uses true differential inputs. According to onsemi documentation, the LM324 series is designed for low-cost, general-purpose applications and provides particular advantages in single-supply systems. A unity-gain bandwidth of approximately 1 MHz is suitable for audio-frequency, sensor-interface, feedback-control, and general analog-signal applications rather than high-speed precision instrumentation.
Typical uses include four-channel sensor conditioning, low-frequency active filters, audio preamplifier stages, comparator functions, industrial control loops, and general-purpose buffering. The four amplifiers can operate independently, although common power rails and package-level thermal behavior should be considered when all channels drive substantial loads.
For new layouts, use the manufacturer pin-description table when assigning PCB tracks and preserve the TSSOP-14 land pattern. Check input common-mode range, output swing, input bias current, noise, offset voltage, and slew rate against the actual signal amplitude and frequency before finalizing the circuit.
This page combines the LM2902DTBG operating limits, package information, replacement options, and practical circuit-placement guidance into an engineering-focused selection resource for buyers and designers evaluating quad single-supply op amps.
直接替換替代品,適用於 LM2902DTBG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2902DTBG (相同外形與佔位) — 差異在於 Package, Gain-Bandwidth Product.
LM2902PWRG4
✅ 直接替換聯絡詢價
查看資料表 →LM2902DTBR2G
✅ 直接替換聯絡詢價
查看資料表 →NCV2902DTBR2G
✅ 直接替換📋 參考替代品(不在目錄中)
LM2902VDTBR2G
✅ 直接替換聯絡詢價
查看資料表 →LM2902KPWRG4
✅ 直接替換📋 參考替代品(不在目錄中)
LM2902DTBG 最大額定值與電氣特性
| Amplifier Count | 4 amplifiers |
| Supply Voltage Range | 3 V to 26 V |
| 工作溫度範圍 | -40 °C to +105 °C |
| 封裝 | 14-pin TSSOP |
| 安裝類型 | Surface mount |
| Product Category | General-purpose operational amplifier |
| Supply Type | Single supply |
| Input Architecture | True differential input |
| Unity-Gain Bandwidth | Approximately 1 MHz |
LM2902DTBG 14-pin tssop 腳位配置指南
LM2902DTBG(14-pin tssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2902DTBG.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2902DTBG 適用於 6 應用s: Industrial Sensor Signal Conditioning, Audio Preamplifier Stages, Active Filters and Control Loops, Comparator and Threshold Detection, Portable and Battery-Powered Analog Circuits, Test and Measurement Front Ends.
Industrial Sensor Signal Conditioning
The LM2902DTBG fits four-channel industrial sensor conditioning because it combines four true-differential-input amplifiers with a 3 V to 26 V single-supply range. Engineers can use the channels for buffering, gain stages, active filtering, or level shifting around low-frequency sensor outputs. Its approximately 1 MHz unity-gain bandwidth is more than adequate for many pressure, temperature, and position signals. The -40 °C to +105 °C rating supports industrial environments, but each sensor interface must still be checked for input common-mode range, offset, bias current, and output-swing requirements.
推薦
Audio Preamplifier Stages
The LM2902DTBG can implement several low-frequency audio preamplifier or mixer channels within one 14-pin TSSOP package. Its four true-differential-input amplifiers are useful for source buffers, volume-control gain stages, and active balancing networks. The 3 V minimum supply supports portable equipment, while operation up to 26 V provides flexibility for higher-voltage analog systems. With approximately 1 MHz unity-gain bandwidth, the device is best suited to voice-band and conventional audio functions rather than high-frequency video or ultrasonic signal paths.
推薦
Active Filters and Control Loops
The LM2902DTBG is appropriate for active low-pass, high-pass, and feedback-control circuits where four general-purpose channels can reduce board area. Its 3 V to 26 V operating range permits implementation on 5 V or 12 V control rails, and the approximately 1 MHz unity-gain bandwidth is sufficient for many audio-band and slow industrial loops. When designing filters, account for resistor tolerances, amplifier offset, noise, output loading, and compensation requirements. The industrial temperature range of -40 °C to +105 °C helps maintain suitability across varied enclosure conditions.
推薦
Comparator and Threshold Detection
The LM2902DTBG can implement up to four independent comparator-style threshold detectors when the signal remains within the amplifier's common-mode and output-swing limits. The 3 V to 26 V supply range is useful for detecting sensor, battery, or divided-reference voltages in industrial systems. Because this is a general-purpose operational amplifier rather than a dedicated open-drain comparator, the output behavior, saturation recovery, input protection, and supply current must be reviewed for the specific application.
推薦
Portable and Battery-Powered Analog Circuits
The LM2902DTBG is suitable for low-frequency analog sections in portable equipment because it supports single-supply operation starting at 3 V and contains four amplifier channels in one TSSOP package. Engineers can use the channels for microphone-style signal conditioning, sensor amplification, gain control, or voltage buffering around a low-voltage system rail. The low-power nature of the LM324 family helps conserve energy, although total current depends on the selected configuration and load. Confirm output load capability, shutdown strategy, and thermal behavior across the complete battery-discharge range.
推薦
Test and Measurement Front Ends
The LM2902DTBG can provide buffering, gain, differential conversion, and active feedback for general-purpose test and measurement equipment. Four channels allow a compact instrument front end to support several probes or repeated measurement stages without using four separate packages. The 3 V to 26 V supply range supports portable and bench equipment, while the -40 °C to +105 °C rating covers extended industrial environments. Precision instrumentation still requires checking offset voltage, input bias current, noise, common-mode range, and stability for the selected gain and frequency.
推薦
推薦產品摘要
工程參考資料,適用於 LM2902DTBG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2902PWRG4 | LM2902DTBR2G | NCV2902DTBR2G | LM2902VDTBR2G | LM2902KPWRG4 |
|---|---|---|---|---|---|---|
| Package | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | onsemi |
| Amplifier Count | 4 amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers |
| Input Architecture | True differential input | True differential input | True differential input | True differential input | True differential input | True differential input |
| Product Family | LM2902 general-purpose quad operational amplifier | LM2902 general-purpose quad operational amplifier | LM2902 general-purpose quad operational amplifier | NCV2902 quad operational amplifier | LM2902 general-purpose quad operational amplifier | LM2902 general-purpose quad operational amplifier |
主要差異化特點
- Combines four amplifier channels in one TSSOP package (對比LM2902PWRG4)
- Single-supply range supports multiple conventional rails (對比LM2902DTBR2G)
- Extended industrial temperature operation (對比NCV2902DTBR2G)
設計說明
Use the manufacturer pin-description table when routing the 14-pin TSSOP layout. Place each amplifier's supply bypass capacitor close to the appropriate power pin, and keep sensitive input and feedback traces short to reduce capacitive pickup. Because all four channels share package leads and thermal paths, avoid long parallel input routes where adjacent channels carry high-level signals. Confirm exposed-pad or thermal requirements against the exact package drawing before release.
Decouple the supply locally with ceramic capacitors selected from the manufacturer's recommended capacitance and voltage-rating guidance. The LM2902DTBG supports 3 V to 26 V operation, but decoupling requirements can vary with supply impedance, cable length, amplifier configuration, and output load. Check each channel's input and output voltage limits at the minimum and maximum local rail voltages; being within the absolute supply rating does not guarantee that every signal remains within the linear common-mode range.
Do not use the approximately 1 MHz unity-gain bandwidth as permission to design a unity-gain stage at 1 MHz. Op-amp stability depends on gain, noise gain, capacitive loading, output impedance, and the feedback network. Also verify input common-mode range, output swing, input offset, and load current. For comparator-style use, check saturation recovery and output behavior because the LM2902DTBG is a linear operational amplifier rather than a dedicated comparator.
Calculate worst-case dissipation from the actual output stage, output current, and voltage drop across the device rather than estimating from total supply current alone. Four active channels can increase package heating even when each amplifier individually carries a modest load. Use the package thermal information and PCB copper area to estimate junction temperature. Estimated: use the maximum expected supply voltage, output voltage, output current, and manufacturer power-dissipation equations for the operating environment.
合規資訊
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were identified for the exact LM2902DTBG ordering code.