LM2904WPT - Dual Low-Power Op Amp | STMicroelectronics
N.º de pieza: LM2904WPT ✓ ActivoLM2904WPT Descripción general
The LM2904 family belongs to the operational amplifier hierarchy: dual operational amplifier -> general-purpose amplifier -> analog signal-conditioning IC -> semiconductor. Its internally compensated architecture simplifies implementation because an external compensation capacitor is not required for closed-loop operation in typical voltage-follower and inverting-amplifier configurations. The two independent amplifiers can also be used in separate signal chains within the same circuit.
The LM2904WPT is identified in the product listings as a 2-circuit, single-ended amplifier in an 8-TSSOP package. The related LM2904AW variant is also documented for automotive and industrial applications. Low power-supply drain, wide single-supply operation, and internal frequency compensation make this family suitable for sensor conditioning, control-loop amplification, audio and instrumentation interfaces, and general industrial electronics.
Because the LM2904WPT is a general-purpose amplifier, application performance depends on the selected gain, feedback network, supply voltage, load, and operating temperature. The datasheet should be consulted for the exact input common-mode range, output swing, input bias current, input offset voltage, supply-current limits, and thermal limits before final circuit sign-off.
For PCB implementation, route the two amplifier sections with short feedback paths, keep input and output nodes away from switching nodes, and place supply-bypass capacitors close to the device pins. A common ground reference and adequate copper area help preserve signal integrity in low-level analog circuits.
This page summarizes the verified device identity, package, application positioning, drop-in sourcing options, and practical design considerations that are useful when evaluating the LM2904WPT for a new analog design.
Alternativas directas para LM2904WPT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LM2904WPT (mismo factor de forma y huella) — difiere en Number of Circuits, Package, REACH Status, RoHS Status.
LM2904WPT
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2904YDT
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM2904WPT Valores máximos y características eléctricas
| Manufacturer | STMicroelectronics |
| Device Type | Dual general-purpose operational amplifier |
| Number of Circuits | 2 |
| Topología | Single-ended |
| Encapsulado | 8-TSSOP |
| Tipo de montaje | Surface mount |
| Supply Configuration | Single supply |
| Voltage Gain | High gain; exact value not stated in the product listing |
| Frequency Compensation | Internal |
| Supply Voltage Range | Wide single-supply range; exact limits not stated in the product listing |
| Supply Drain | Low power-supply drain, independent of supply-voltage magnitude |
| Automotive Application | Designed for automotive and industrial control systems |
| Estado RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_qualified |
| Datasheet Page Count | 19 pages in the listed PDF document |
Configuración de pines de LM2904WPT
| Pin 1 | OUT A — Output of amplifier A |
| Pin 2 | IN- A — Inverting input of amplifier A |
| Pin 3 | IN+ A — Non-inverting input of amplifier A |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | IN+ B — Non-inverting input of amplifier B |
| Pin 6 | IN- B — Inverting input of amplifier B |
| Pin 7 | OUT B — Output of amplifier B |
| Pin 8 | V+ — Positive supply connection |
Aplicaciones típicas
LM2904WPT es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Automotive Control Module Amplification, Power Supply Feedback and Control Loops, Audio Preamplifier Stages, Instrumentation and Measurement Interfaces, Low-Power Embedded Control Interfaces.
Industrial Sensor Signal Conditioning
The LM2904WPT is suitable for conditioning low-level sensor signals in industrial control systems because it provides two independent, high-gain amplifier sections with internal frequency compensation. One section can amplify a bridge or transducer signal while the other provides gain, filtering, or buffering for a second channel. Its single-supply operation and low power-supply drain suit compact control boards where supply headroom is limited. The design still requires verification of the exact input common-mode range, output swing, offset voltage, and bias current in the manufacturer datasheet for the selected supply voltage.
Recomendado
Automotive Control Module Amplification
The LM2904W and LM2904AW family is expressly described by STMicroelectronics for automotive and industrial control systems, making the LM2904WPT applicable to low-speed control and conditioning circuits in electronic modules. Its two independent amplifiers can serve separate analog channels within the same package, reducing board area compared with two single amplifiers. Because automotive qualification and environmental requirements vary by ordering code, engineers should confirm the exact temperature grade, AEC-Q100 status, ESD behavior, and automotive qualification documentation rather than infer it from the family name.
Recomendado
Power Supply Feedback and Control Loops
The LM2904WPT can amplify voltage-feedback or current-sense signals in power-supply control loops using its high-gain, internally compensated amplifier sections. Internal frequency compensation avoids an external compensation capacitor in standard closed-loop configurations, while the low supply drain helps control auxiliary power consumption. Designers should place the amplifier close to the feedback divider or shunt element to minimize pickup, keep the feedback trace away from switching nodes, and verify stability against the crossover frequency and output capacitance of the power stage.
Recomendado
Audio Preamplifier Stages
The two independent LM2904WPT amplifier sections can implement separate audio preamplifier or mixing stages in consumer and industrial audio equipment. Their high gain supports resistive feedback networks, while internal frequency compensation simplifies ordinary inverting and non-inverting layouts. Performance depends on the feedback values, source impedance, and load, so the amplifier's input offset, bias current, noise, output swing, and stability into the intended load should be checked. A ground-plane arrangement that keeps both channels away from switching regulators and motor drive nodes is especially important in a mixed-signal audio board.
Recomendado
Instrumentation and Measurement Interfaces
The LM2904WPT can serve as the first active stage in instrumentation interfaces where a transducer or resistive sensor produces a low-level differential or single-ended signal. Its internal frequency compensation supports straightforward closed-loop gain stages and reduces the number of external components, while the 8-TSSOP package keeps dual-channel designs compact. For instrumentation-grade accuracy, verify offset voltage, input bias current, common-mode range, drift, and open-loop behavior against the measurement budget, and use a shielded or guarded layout for high-impedance sensor inputs.
Recomendado
Low-Power Embedded Control Interfaces
The LM2904WPT fits embedded control boards that require two general-purpose analog channels without adding a high-performance amplifier that would raise cost or supply demand. One amplifier can condition a potentiometer or analog status input, while the other can drive a feedback signal or buffer a reference. The family-level low power-supply drain, single-supply capability, and internal compensation align well with compact embedded designs. Firmware-controlled gain selection should still avoid operating the amplifier outside its input and output ranges, and unused amplifier sections should be tied to a defined common-mode voltage.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM2904WPT — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM2904WPT | LM2904YDT |
|---|---|---|---|
| Brand | STMicroelectronics | ROHM Semiconductor | STMicroelectronics |
| Package | 8-TSSOP | 8-TSSOP-B | 8-TSSOP |
| Number of Amplifiers | 2 | 2 | 2 |
| Amplifier Class | General purpose | General purpose | General purpose LM2904 family |
| Frequency Compensation | Internal | Internal for the LM2904W family | Internal for the LM2904 family |
| Supply Configuration | Single supply | Single supply | Single supply |
| Supply Drain | Low and independent of supply-voltage magnitude | Low; exact limit depends on manufacturer device specification | Low; exact limit depends on suffix specification |
| Application Positioning | Automotive and industrial control systems | General-purpose dual amplifier | General-purpose LM2904-family dual amplifier |
| RoHS Status | unknown | unknown | unknown |
Diferenciadores clave
- Verified identical ordering code from a second manufacturer (frente a ROHM Semiconductor LM2904WPT)
- Family-level internal frequency compensation (frente a STMicroelectronics LM2904YDT)
- Dual independent amplifiers in a compact surface-mount package (frente a ROHM Semiconductor LM2904WPT)
- Single-supply operation with supply-independent low drain (frente a STMicroelectronics LM2904YDT)
Notas de diseño
Place the supply-bypass capacitor immediately adjacent to the LM2904WPT supply and ground pins, and keep feedback traces short and direct. Place both amplifier sections on the same side of the board where practical so their ground returns share a low-impedance path. Avoid routing inputs and outputs beneath or beside switching-regulator nodes, relay contacts, and high-current motor returns because capacitive coupling can turn a stable closed-loop stage into an oscillator.
Do not assume that every LM2904 ordering code is an exact drop-in replacement solely because the family name matches. Check pin functions, supply-voltage limits, input common-mode range, output swing, input offset voltage, input bias current, quiescent current, and temperature grade. For a non-inverting amplifier, confirm that the input and output remain inside the permitted ranges at the intended supply voltage; for an inverting amplifier, confirm that the non-inverting input is biased within the common-mode range.
Use the lowest practical feedback resistance that keeps the required gain and bandwidth. Excessively large resistors increase sensitivity to input-bias-current error, leakage, and noise, while excessively small values can load the source and increase power consumption. High-impedance sensor nodes should be guarded, and a driven shield or nearby ground reference can help reduce pickup when the sensor output impedance is high.
Budget supply current for both amplifier sections, not only the active channel, because the family description identifies low supply drain that is independent of supply-voltage magnitude but does not imply that the second section can be ignored. Verify total quiescent and output-current requirements at the maximum operating temperature. Where possible, keep unused amplifier inputs biased at a defined common-mode voltage rather than allowing them to float.
Información de cumplimiento
The family is described for automotive and industrial control systems, but the verified snippets do not confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for the exact LM2904WPT ordering code. Request current compliance documentation from the manufacturer through the Request a Quote form on this page.