MAX3221CPWRG4 - 250kbps RS-232 Transceiver | Texas Instruments
N.º de pieza: MAX3221CPWRG4 ✓ ActivoMAX3221CPWRG4 Descripción general
A transceiver converts logic-level signals into RS-232-compatible differential voltage levels and converts received RS-232 levels back into CMOS-compatible logic. Within the broader communications hierarchy, this device is an RS-232 interface transceiver, a line-driver and receiver IC, and ultimately a signal-conditioning device for serial data links. It is intended for equipment-to-equipment and point-to-point serial communication rather than long-distance networking.
Key features include a 3 V to 5.5 V operating range, operation at up to 250 kbit/s, low standby current of 1 µA typical, and compatibility with 5 V logic inputs when operated from a 3.3 V supply. The MAX3221 design uses external 0.1 µF charge-pump capacitors, allowing the interface to generate the bipolar voltage required by RS-232 without a separate DC-DC converter. TI identifies the device as interoperable with equivalent single-channel interface transceivers.
The device conforms to TIA/EIA-232-F and ITU V.28 signaling requirements. Its transmitter provides the voltage swing required to drive a standard RS-232 receiver, while its receiver recognizes the negative-going voltage used for a valid RS-232 logic mark. The integrated ±15 kV ESD protection improves survivability when cables are connected or disconnected in industrial, instrumentation, and data-acquisition environments.
Typical uses include industrial control consoles, test and measurement equipment, instrumentation links, embedded serial ports, and service-port connections between a host and peripheral. Because the MAX3221 provides only one driver and one receiver, two transceivers are normally required for a full-duplex point-to-point link with transmit and receive data flowing simultaneously.
When laying out the circuit, place the 0.1 µF charge-pump capacitors close to their associated pins and route the RS-232 driver output and receiver input away from sensitive analog or high-speed digital traces. Confirm that the logic-side supply voltage matches the host interface, and verify the ground connection between both ends of the cable before relying on common-mode rejection.
This page combines the device ratings, package information, functional guidance, pin-level design considerations, and available drop-in alternatives to support faster component selection and PCB implementation.
Alternativas directas para MAX3221CPWRG4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX3221CPWRG4 (mismo factor de forma y huella) — difiere en ESD Protection, Package, Product Type, Logic Input Compatibility, Maximum Data Rate.
MAX3221ECPWRG4
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MAX3221IPWRG4
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX3221CPW
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX3221CPWRG4 Especificaciones
| Product Type | Single-channel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Driver and Receiver Configuration | 1/1 full-duplex transceiver |
| ESD Protection | ±15 kV |
| RS-232 Standard | TIA/EIA-232-F |
| International Standard | ITU V.28 |
| Low Standby Current | 1 µA typical |
| External Charge-Pump Capacitors | 0.1 µF |
| Logic Input Compatibility | Accepts 5 V logic input with a 3.3 V supply |
| Interchangeability | Designed to be interchangeable with equivalent devices |
| Encapsulado | 16-pin TSSOP, 4.40 mm width |
| Tipo de montaje | Surface mount |
| Estado RoHS | RoHS compliant |
Guía de configuración de pines de MAX3221CPWRG4 16-pin tssop, 4.40 mm width
Configuración de pines para MAX3221CPWRG4 (encapsulado 16-pin tssop, 4.40 mm width). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX3221CPWRG4.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX3221CPWRG4 es adecuado para 6 aplicacións: Embedded Serial Console, Industrial Test and Measurement Equipment, Point-to-Point Data Acquisition Link, Instrument Service and Configuration Port, Controller Communication Gateway, Portable Equipment Interface.
Embedded Serial Console
The MAX3221CPWRG4 suits an embedded controller that needs one legacy RS-232 port for configuration, diagnostics, or boot logging. Its 3 V to 5.5 V supply range allows operation directly from a 3.3 V system rail, and the 1 µA typical standby current limits the penalty when the interface is inactive. Use one driver and one receiver for a unidirectional console path, or pair two devices when command traffic must flow in both directions. The 250 kbit/s limit comfortably covers interactive terminal traffic, while the ±15 kV protected RS-232 pins improve reliability when a service cable is connected in the field.
Recomendado
Industrial Test and Measurement Equipment
The MAX3221CPWRG4 provides a compact interface between a test instrument and a controller that still uses RS-232. The device operates up to 250 kbit/s, supports both 3.3 V and 5 V supply arrangements, and accepts 5 V logic inputs from a 3.3 V supply. Its single-channel format leaves board area for measurement circuitry, storage, and front-panel interfaces. Place the 0.1 µF charge-pump capacitors close to their pins, and keep the protected cable-side nets away from sensitive analog traces to prevent switching transients from coupling into the measurement front end.
Recomendado
Point-to-Point Data Acquisition Link
The MAX3221CPWRG4 can carry measurement commands and returned data over a dedicated RS-232 connection between two instrumented systems. A transmitter on one board and receiver on the other form one direction; adding a second transceiver at each end enables simultaneous bidirectional transfer. The 250 kbit/s bandwidth supports moderate-rate telemetry rather than bulk file transfer. Because the interface is single-ended, maintain a common ground between equipment and route the cable-side driver output away from precision analog inputs. The ±15 kV ESD rating adds useful protection for externally accessible connections.
Recomendado
Instrument Service and Configuration Port
The MAX3221CPWRG4 is useful for a service port that allows technicians to configure a controller, update settings, or retrieve diagnostic data. Its single driver and receiver minimize the footprint compared with a two-channel RS-232 device, while the 16-pin TSSOP package supports compact assembly. The 3 V to 5.5 V operating range allows the same circuit to serve legacy 5 V equipment and newer 3.3 V controllers. Use the manufacturer pin table to assign logic signals, connect the 0.1 µF charge-pump capacitors directly at the device, and place protection components where the cable enters the enclosure.
Recomendado
Controller Communication Gateway
The MAX3221CPWRG4 can bridge a modern controller to an RS-232 peripheral when only one legacy channel is required. The controller can use 3.3 V logic while the interface remains compatible with 5 V logic inputs, reducing the need for a separate interface translator. The device's 250 kbit/s throughput is suitable for status polling, configuration commands, and moderate data packets. For continuous bidirectional service operation, use two MAX3221 devices rather than forcing unidirectional traffic through one half-duplex arrangement, and validate the protocol timeout behavior with the slowest connected peripheral.
Recomendado
Portable Equipment Interface
The MAX3221CPWRG4 fits portable or battery-powered equipment that requires an RS-232 connection without a large interface circuit. Its 1 µA typical standby current is useful when the serial function is enabled only during setup or service, and its 3 V operation supports lithium-powered designs with a 3.3 V rail. The 16-pin TSSOP package leaves board area for battery management and display circuitry. Use the shutdown-capable MAX3221ECPWRG4 variant if the interface must disconnect more aggressively, and verify that the cable-side ground reference is appropriate for a portable system that may be externally connected.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX3221CPWRG4 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX3221ECPWRG4 | MAX3221IPWRG4 | MAX3221CPW |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin TSSOP | 16-pin TSSOP - same | 16-pin TSSOP - same | 16-pin TSSOP - same |
| Device Type | Single-channel RS-232 line driver and receiver | Single-channel RS-232 line driver and receiver | Single-channel RS-232 line driver and receiver | Single-channel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s | 250 kbit/s | 250 kbit/s | 250 kbit/s |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver |
| External Charge-Pump Capacitors | 0.1 µF | 0.1 µF | 0.1 µF | 0.1 µF |
Diferenciadores clave
- Single-channel implementation preserves PCB area (frente a MAX3221ECPWRG4)
- Green-compatible ordering option (frente a MAX3221CPW)
- Directly supports low-voltage embedded logic (frente a MAX3221IPWRG4)
Notas de diseño
Place the two 0.1 µF charge-pump capacitors directly beside their specified MAX3221 pins, with short traces and a solid ground-plane connection. Keep the switching-capacitor current loop compact and avoid routing it beneath sensitive analog inputs. If the RS-232 connector is near the board edge, position the protected transceiver pins ahead of any long unprotected trace so that the ESD-designated interface receives the first electrical stress.
Route the RS-232 driver output and receiver input as a matched pair where practical, while keeping them away from clocks, switching-regulator nodes, and high-gain analog inputs. The MAX3221 supplies bipolar levels from a single 3 V to 5.5 V rail, but its charge-pump switching edges can couple into nearby circuitry. Maintain a continuous ground reference between communicating systems and avoid long ground stubs beneath the cable-side signal path.
Do not treat a single MAX3221 as a complete bidirectional link. One device provides one driver and one receiver, so full-duplex communication normally requires a second device at the opposite endpoint. Also verify that the host-side logic voltage is compatible with the 3 V to 5.5 V supply selection and that the selected MAX3221 ordering suffix matches the required production packaging before releasing the PCB.
Información de cumplimiento
RoHS compliance is identified by distributor and cross-reference listings, and the G4 ordering designation denotes the green-compatible version. No specific REACH, halogen-free, or conflict-minerals declaration is included in the cited product information. AEC-Q100 status is not applicable to this general-purpose interface IC.