MAX3221CPWRG4 - 250kbps RS-232 Transceiver | Texas Instruments
부품 번호: MAX3221CPWRG4 ✓ 활성MAX3221CPWRG4 개요
A transceiver converts logic-level signals into RS-232-compatible differential voltage levels and converts received RS-232 levels back into CMOS-compatible logic. Within the broader communications hierarchy, this device is an RS-232 interface transceiver, a line-driver and receiver IC, and ultimately a signal-conditioning device for serial data links. It is intended for equipment-to-equipment and point-to-point serial communication rather than long-distance networking.
Key features include a 3 V to 5.5 V operating range, operation at up to 250 kbit/s, low standby current of 1 µA typical, and compatibility with 5 V logic inputs when operated from a 3.3 V supply. The MAX3221 design uses external 0.1 µF charge-pump capacitors, allowing the interface to generate the bipolar voltage required by RS-232 without a separate DC-DC converter. TI identifies the device as interoperable with equivalent single-channel interface transceivers.
The device conforms to TIA/EIA-232-F and ITU V.28 signaling requirements. Its transmitter provides the voltage swing required to drive a standard RS-232 receiver, while its receiver recognizes the negative-going voltage used for a valid RS-232 logic mark. The integrated ±15 kV ESD protection improves survivability when cables are connected or disconnected in industrial, instrumentation, and data-acquisition environments.
Typical uses include industrial control consoles, test and measurement equipment, instrumentation links, embedded serial ports, and service-port connections between a host and peripheral. Because the MAX3221 provides only one driver and one receiver, two transceivers are normally required for a full-duplex point-to-point link with transmit and receive data flowing simultaneously.
When laying out the circuit, place the 0.1 µF charge-pump capacitors close to their associated pins and route the RS-232 driver output and receiver input away from sensitive analog or high-speed digital traces. Confirm that the logic-side supply voltage matches the host interface, and verify the ground connection between both ends of the cable before relying on common-mode rejection.
This page combines the device ratings, package information, functional guidance, pin-level design considerations, and available drop-in alternatives to support faster component selection and PCB implementation.
드롭인 대체품: MAX3221CPWRG4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MAX3221CPWRG4 (동일 폼 팩터 및 풋프린트) — 차이점: ESD Protection, Package, Product Type, Logic Input Compatibility, Maximum Data Rate.
MAX3221ECPWRG4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MAX3221IPWRG4
✅ 드롭인가격 문의
데이터시트 보기 →MAX3221CPW
✅ 드롭인가격 문의
데이터시트 보기 →MAX3221CPWRG4 사양
| Product Type | Single-channel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Driver and Receiver Configuration | 1/1 full-duplex transceiver |
| ESD Protection | ±15 kV |
| RS-232 Standard | TIA/EIA-232-F |
| International Standard | ITU V.28 |
| Low Standby Current | 1 µA typical |
| External Charge-Pump Capacitors | 0.1 µF |
| Logic Input Compatibility | Accepts 5 V logic input with a 3.3 V supply |
| Interchangeability | Designed to be interchangeable with equivalent devices |
| 패키지 | 16-pin TSSOP, 4.40 mm width |
| 실장 유형 | Surface mount |
| RoHS 상태 | RoHS compliant |
MAX3221CPWRG4 16-pin tssop, 4.40 mm width 핀 구성 가이드
MAX3221CPWRG4(16-pin tssop, 4.40 mm width 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MAX3221CPWRG4.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MAX3221CPWRG4 적합 용도: 6 애플리케이션s: Embedded Serial Console, Industrial Test and Measurement Equipment, Point-to-Point Data Acquisition Link, Instrument Service and Configuration Port, Controller Communication Gateway, Portable Equipment Interface.
Embedded Serial Console
The MAX3221CPWRG4 suits an embedded controller that needs one legacy RS-232 port for configuration, diagnostics, or boot logging. Its 3 V to 5.5 V supply range allows operation directly from a 3.3 V system rail, and the 1 µA typical standby current limits the penalty when the interface is inactive. Use one driver and one receiver for a unidirectional console path, or pair two devices when command traffic must flow in both directions. The 250 kbit/s limit comfortably covers interactive terminal traffic, while the ±15 kV protected RS-232 pins improve reliability when a service cable is connected in the field.
추천
Industrial Test and Measurement Equipment
The MAX3221CPWRG4 provides a compact interface between a test instrument and a controller that still uses RS-232. The device operates up to 250 kbit/s, supports both 3.3 V and 5 V supply arrangements, and accepts 5 V logic inputs from a 3.3 V supply. Its single-channel format leaves board area for measurement circuitry, storage, and front-panel interfaces. Place the 0.1 µF charge-pump capacitors close to their pins, and keep the protected cable-side nets away from sensitive analog traces to prevent switching transients from coupling into the measurement front end.
추천
Point-to-Point Data Acquisition Link
The MAX3221CPWRG4 can carry measurement commands and returned data over a dedicated RS-232 connection between two instrumented systems. A transmitter on one board and receiver on the other form one direction; adding a second transceiver at each end enables simultaneous bidirectional transfer. The 250 kbit/s bandwidth supports moderate-rate telemetry rather than bulk file transfer. Because the interface is single-ended, maintain a common ground between equipment and route the cable-side driver output away from precision analog inputs. The ±15 kV ESD rating adds useful protection for externally accessible connections.
추천
Instrument Service and Configuration Port
The MAX3221CPWRG4 is useful for a service port that allows technicians to configure a controller, update settings, or retrieve diagnostic data. Its single driver and receiver minimize the footprint compared with a two-channel RS-232 device, while the 16-pin TSSOP package supports compact assembly. The 3 V to 5.5 V operating range allows the same circuit to serve legacy 5 V equipment and newer 3.3 V controllers. Use the manufacturer pin table to assign logic signals, connect the 0.1 µF charge-pump capacitors directly at the device, and place protection components where the cable enters the enclosure.
추천
Controller Communication Gateway
The MAX3221CPWRG4 can bridge a modern controller to an RS-232 peripheral when only one legacy channel is required. The controller can use 3.3 V logic while the interface remains compatible with 5 V logic inputs, reducing the need for a separate interface translator. The device's 250 kbit/s throughput is suitable for status polling, configuration commands, and moderate data packets. For continuous bidirectional service operation, use two MAX3221 devices rather than forcing unidirectional traffic through one half-duplex arrangement, and validate the protocol timeout behavior with the slowest connected peripheral.
추천
Portable Equipment Interface
The MAX3221CPWRG4 fits portable or battery-powered equipment that requires an RS-232 connection without a large interface circuit. Its 1 µA typical standby current is useful when the serial function is enabled only during setup or service, and its 3 V operation supports lithium-powered designs with a 3.3 V rail. The 16-pin TSSOP package leaves board area for battery management and display circuitry. Use the shutdown-capable MAX3221ECPWRG4 variant if the interface must disconnect more aggressively, and verify that the cable-side ground reference is appropriate for a portable system that may be externally connected.
추천
추천 제품 요약
엔지니어링 참조 데이터: MAX3221CPWRG4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MAX3221ECPWRG4 | MAX3221IPWRG4 | MAX3221CPW |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin TSSOP | 16-pin TSSOP - same | 16-pin TSSOP - same | 16-pin TSSOP - same |
| Device Type | Single-channel RS-232 line driver and receiver | Single-channel RS-232 line driver and receiver | Single-channel RS-232 line driver and receiver | Single-channel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s | 250 kbit/s | 250 kbit/s | 250 kbit/s |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver |
| External Charge-Pump Capacitors | 0.1 µF | 0.1 µF | 0.1 µF | 0.1 µF |
주요 차별점
- Single-channel implementation preserves PCB area (vs MAX3221ECPWRG4)
- Green-compatible ordering option (vs MAX3221CPW)
- Directly supports low-voltage embedded logic (vs MAX3221IPWRG4)
설계 노트
Place the two 0.1 µF charge-pump capacitors directly beside their specified MAX3221 pins, with short traces and a solid ground-plane connection. Keep the switching-capacitor current loop compact and avoid routing it beneath sensitive analog inputs. If the RS-232 connector is near the board edge, position the protected transceiver pins ahead of any long unprotected trace so that the ESD-designated interface receives the first electrical stress.
Route the RS-232 driver output and receiver input as a matched pair where practical, while keeping them away from clocks, switching-regulator nodes, and high-gain analog inputs. The MAX3221 supplies bipolar levels from a single 3 V to 5.5 V rail, but its charge-pump switching edges can couple into nearby circuitry. Maintain a continuous ground reference between communicating systems and avoid long ground stubs beneath the cable-side signal path.
Do not treat a single MAX3221 as a complete bidirectional link. One device provides one driver and one receiver, so full-duplex communication normally requires a second device at the opposite endpoint. Also verify that the host-side logic voltage is compatible with the 3 V to 5.5 V supply selection and that the selected MAX3221 ordering suffix matches the required production packaging before releasing the PCB.
규정 준수 정보
RoHS compliance is identified by distributor and cross-reference listings, and the G4 ordering designation denotes the green-compatible version. No specific REACH, halogen-free, or conflict-minerals declaration is included in the cited product information. AEC-Q100 status is not applicable to this general-purpose interface IC.