MAX3243EETI+T - 250kbps RS-232 Transceiver | Analog Devices
N.º de pieza: MAX3243EETI+T ✓ ActivoMAX3243EETI+T Descripción general
A multi-channel RS-232 transceiver combines push-pull line drivers and receivers for bidirectional data transfer between a host and an external serial device. In the broader hierarchy, MAX3243EETI+T is an interface transceiver, an interface IC, and a semiconductor for establishing the physical signal layer required by RS-232 equipment. The AutoShutdown function is particularly useful in battery-powered instruments, portable test equipment, and systems where an inactive serial port must not continue consuming power.
The 3V to 5.5V operating range permits operation from both 3.3V and 5V system rails. Its 250kbps maximum signaling rate supports data rates above the traditional 20kbps RS-232 limit while remaining suitable for instrument control, point-of-sale equipment, industrial controllers, and embedded peripheral links. ±15kV ESD protection improves tolerance of connector-borne transients, although it does not eliminate the need for correct board layout and external protection strategy.
The MAX3243 family combines low-power supply design with multiple driver and receiver channels. AutoShutdown detects whether valid signal levels appear on receiver inputs and disables the internal supply and drivers when the port is idle. This behavior allows a direct interface to operate from modern low-voltage digital rails without requiring a separate power-control transistor. The exact charge-pump, driver-slew, and receiver-threshold details should be confirmed against the manufacturer datasheet before finalizing a new design.
Typical uses include multichannel instrument-control links, data acquisition, barcode and point-of-sale terminals, industrial serial adapters, and embedded systems that exchange RS-232 data with legacy peripherals. The 28-terminal QFN footprint also requires careful PCB planning because its compact leadless geometry leaves less visible inspection area and demands accurate land patterns, solder-paste control, and thermal-via placement.
For a robust implementation, keep the MAX3243EETI+T close to the RS-232 connector, route driver and receiver traces away from sensitive analog circuitry, and place charge-pump and interface capacitors at the pins specified by the reference design. Confirm signal polarity, receiver thresholds, shutdown behavior, and grounding with the system-level RS-232 requirements rather than assuming that every ±15V RS-232-compatible product is electrically interchangeable.
This page combines manufacturer specifications, package information, practical RS-232 design guidance, and carefully qualified same-family replacement options. It is intended to help engineers determine whether the MAX3243EETI+T fits the required voltage, data rate, channel count, package, and protection level before committing the part to a PCB or production BOM.
Alternativas directas para MAX3243EETI+T — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MAX3243EETI+T (mismo factor de forma y huella) — difiere en Package, Supply Voltage Range, Maximum Data Rate, ESD Protection, Product Type.
MAX3243EEUI+T
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX3243EETJ+T
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX3243EWI+T
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →MAX3243EETI+T Especificaciones
| Product Type | RS-232 line driver and receiver |
| Number of Driver/Receiver Channels | 3 channels |
| Supply Voltage Range | 3V to 5.5V |
| Maximum Data Rate | 250kbps |
| ESD Protection | ±15kV |
| AutoShutdown Supply Current | 1µA |
| Power-Saving Feature | AutoShutdown |
| Temperature Grade | Industrial |
| Number of Terminals | 28 terminals |
| Package Code | QCCN |
| Package Shape | Square |
| Terminal Form | No lead |
| Tipo de montaje | Surface mount |
| Product Type Hierarchy | RS-232 transceiver > interface transceiver > interface IC > semiconductor |
| Interface Standard | RS-232 |
Guía de configuración de pines de MAX3243EETI+T square
Configuración de pines para MAX3243EETI+T (encapsulado square). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX3243EETI+T.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX3243EETI+T es adecuado para 6 aplicacións: Industrial instrument control, Portable data acquisition, Point-of-sale terminal interface, Embedded serial adapter, Barcode and scanner interface, Legacy peripheral connectivity.
Industrial instrument control
The MAX3243EETI+T fits industrial instrument controllers that exchange commands and measurements over RS-232. Its three-channel arrangement supports multiple serial links without requiring a separate transceiver for each connection, while the 250kbps rate exceeds the throughput of a conventional 20kbps RS-232 port. The 3V-to-5.5V supply range permits use with 3.3V and 5V control electronics. The ±15kV ESD rating is useful at accessible instrument connectors, although enclosure and cable practices remain important. AutoShutdown can reduce idle consumption to 1µA when valid receiver activity is absent, helping conserve power in supervisory or intermittently connected test systems.
Recomendado
Portable data acquisition
Portable data-acquisition units can use the MAX3243EETI+T to connect a controller to external sensors, fixtures, or laboratory computers through RS-232. The 250kbps maximum data rate supports compact command and measurement traffic, and the 3V-to-5.5V operating range accommodates both 3.3V and 5V platforms. AutoShutdown is valuable when acquisition occurs intermittently because the transceiver can reduce supply current to 1µA when no valid receiver signal is detected. Its 28-terminal QCCN package also conserves board area, but designers must allocate the exact land pattern and confirm connector-side grounding and signal polarity.
Recomendado
Point-of-sale terminal interface
The MAX3243EETI+T is appropriate for point-of-sale equipment that connects a peripheral, printer, scanner, or service terminal through RS-232. Three driver and receiver channels can organize separate data, control, and status paths, while operation from 3.3V or 5V rails supports embedded terminal designs. The 250kbps rate provides margin for transaction and diagnostic traffic. AutoShutdown lowers standby consumption when the port is inactive, while ±15kV ESD protection adds useful defense at a physically accessible connector. Firmware should avoid false valid-signal detection from idle-line biasing, and the selected cables must preserve the intended RS-232 signal polarity.
Recomendado
Embedded serial adapter
A compact embedded adapter can use the MAX3243EETI+T to bridge a modern controller to an RS-232 device. The low-voltage 3V-to-5.5V supply range avoids requiring a dedicated 5V-only interface rail, and three channels reduce the component count when multiple legacy ports are present. At rates up to 250kbps, the transceiver can handle configuration exchanges, diagnostic logs, and short data packets. Its 28-terminal QCCN package reduces PCB area but requires careful escape routing and assembly control. AutoShutdown can further reduce standby power in battery-operated adapters when the linked equipment leaves the receive lines idle.
Recomendado
Barcode and scanner interface
The MAX3243EETI+T can serve barcode scanners, identification terminals, and local service equipment that communicate with a host through RS-232. The 250kbps capability is substantially faster than a traditional 20kbps interface and comfortably accommodates short scanner packets and command traffic. Operating from 3V to 5.5V makes it practical in mixed-voltage embedded systems, while three channels allow dedicated paths for data, control, and handshake signals. The 1µA AutoShutdown current reduces standby demand when the scanner is disconnected, and ±15kV ESD protection strengthens the interface against electrostatic discharge encountered during service and handling.
Recomendado
Legacy peripheral connectivity
The MAX3243EETI+T is useful when a modern processor must communicate with a legacy printer, controller, or service peripheral that exposes only RS-232. Its three driver/receiver channels support a flexible allocation of transmit, receive, and control signals, while the 250kbps rate improves responsiveness compared with a conventional 20kbps port. The 3V-to-5.5V supply range allows direct operation from common embedded rails without a separate level-shifting supply. AutoShutdown reduces idle power, but the system must account for valid-signal detection on idle lines. The QCCN-28 footprint should be compared carefully with any board-reuse plan.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX3243EETI+T — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX3243EEUI+T | MAX3243EETJ+T | MAX3243EWI+T |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | QCCN-28 | QCCN-28 | QCCN-28 | QCCN-28 |
| Product Type | RS-232 line driver and receiver | RS-232 line driver and receiver | RS-232 line driver and receiver | RS-232 line driver and receiver |
| Terminal Count | 28 terminals | 28 terminals | 28 terminals | 28 terminals |
| Power-Saving Feature | AutoShutdown | AutoShutdown | AutoShutdown | AutoShutdown |
Diferenciadores clave
- Three-channel RS-232 integration in a compact QCCN package (frente a MAX3243EETJ+T)
- Low-power idle operation for embedded and portable systems (frente a MAX3243EEUI+T)
- Connector-side ESD protection at a higher data rate (frente a MAX3243EWI+T)
Notas de diseño
Use the manufacturer QCCN-28 land pattern and place the required bypass and charge-pump capacitors directly at their designated pins. A leadless QCCN package has short electrical escapes and limited solder-joint inspection area, so small placement deviations can create assembly defects. Keep the transceiver close to the RS-232 connector, preserve adequate return-path continuity, and avoid routing driver outputs beneath sensitive analog or clock traces. Use thermal vias beneath the exposed pad only as directed by the package drawing and assembly guidelines.
Decouple the 3V-to-5.5V supply at the MAX3243EETI+T and follow the manufacturer capacitor values and tolerances. The internal charge-pump circuitry depends on stable supply and external charge-pump components; incorrect capacitance or excessive trace resistance can increase ripple or impair startup. Verify the supply remains within 3V to 5.5V under transient conditions. AutoShutdown reduces the specified idle supply current to 1µA, but it does not remove the requirement for local decoupling during active communication.
Keep RS-232 driver traces away from receiver and low-level analog inputs. Route the connector-side signal and return conductors together where practical to reduce loop area and improve noise immunity. Do not treat the ±15kV ESD rating as a substitute for enclosure grounding or an appropriate external surge-protection strategy. Also verify that no external pull-up, pull-down, or transceiver keeps the receiver inputs at a level that prevents the MAX3243 from detecting a valid signal and entering its intended shutdown state.
Do not substitute MAX3243 family members solely because their headline specifications and package names appear similar. Confirm the exact pin names, exposed-pad connection, temperature range, package dimensions, ordering suffix, and qualification status against the manufacturer documentation. In particular, the MAX3243EEUI+T, MAX3243EETJ+T, and MAX3243EWI+T candidates require suffix-specific review before they are treated as production drop-ins for MAX3243EETI+T.
Información de cumplimiento
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was available for the exact MAX3243EETI+T ordering code. Industrial temperature grade is identified, but that designation alone does not establish AEC-Q100 qualification.