MAX383CPE+ - Dual SPDT 35Ω Analog Switch | Analog Devices
N.º de pieza: MAX383CPE+ ✓ ActivoMAX383CPE+ Descripción general
An analog switch is an electronic routing device that connects one signal terminal to one of two alternatives under digital control. A single-pole double-throw switch, or SPDT, has one common terminal and two switched terminals. The MAX383 places two SPDT switches in one 16-pin package, placing it in the hierarchy of CMOS analog switches, analog multiplexers, interface ICs, and semiconductor signal-routing components.
Each MAX383 channel has one normally open and one normally closed path. According to the manufacturer product page, the on-resistance is less than 35Ω, channel matching is guaranteed within 2Ω, and the resistance remains flat over the operating signal range. These characteristics make the matched channels useful when amplitude accuracy across a dual-channel path is more important than minimizing resistance absolutely.
The MAX383 family supports both single-supply and dual-supply operation. Its specified turn-on and turn-off times are 175ns and 100ns, respectively, enabling controlled signal routing with relatively little transition delay. The low-voltage CMOS implementation is suited to battery-powered, industrial control, instrumentation, and test-equipment systems where low-voltage logic and analog signals share the same board.
Typical uses include selecting between two sensor channels, routing test signals, switching bipolar or unipolar analog inputs, and implementing sample-and-hold paths. Two integrated SPDT switches can route complementary or paired signals while keeping channel timing and resistance characteristics closely matched.
Designers should maintain the specified 3V to 15V supply range, use pull-up or pull-down resistors where control or common-pin states require defined levels, and account for charge injection and off-state leakage when switching high-impedance or precision measurement circuits. The through-hole PDIP-16 package also simplifies prototype assembly and legacy PCB maintenance.
This page combines manufacturer specifications, matched-channel design guidance, sourcing information, package details, and same-family replacement analysis to support practical analog-switch selection beyond a basic distributor parameter summary.
Alternativas directas para MAX383CPE+ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
MAX383EPE+
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX383APE+
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX383CPE
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX383CPE++
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX383EPE
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MAX383CPE+ Valores máximos y características eléctricas
| Number of Switches | 2 |
| Number of Channels | 2 |
| Switch Configuration | 2 x SPDT |
| On-Resistance | Less than 35Ω |
| Channel Resistance Matching | Within 2Ω |
| Supply Voltage Range | 3V to 15V |
| Dual Supply Voltage Range | ±3V to ±8V |
| Turn-On Time | 175ns |
| Turn-Off Time | 100ns |
| Rango de temperatura de funcionamiento | 0°C to +70°C |
| Temperature Grade | Commercial |
| Encapsulado | PDIP-16 |
| Number of Terminals | 16 |
| Tipo de montaje | Through Hole |
| Packaging | Tube |
| Switch Type | Normally Open and Normally Closed Poles |
| Estado RoHS | unknown |
Guía de configuración de pines de MAX383CPE+ pdip-16
Configuración de pines para MAX383CPE+ (encapsulado pdip-16). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para MAX383CPE+.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MAX383CPE+ es adecuado para 6 aplicacións: Sensor Signal Selection, Precision Test and Measurement Routing, Battery-Powered Data Acquisition, Bipolar Analog Signal Multiplexing, Sample-and-Hold Signal Routing, Industrial Control Signal Multiplexing.
Sensor Signal Selection
The MAX383CPE+ can select between two sensor outputs through its two independent SPDT channels while maintaining less than 35Ω on-resistance. The manufacturer guarantees channel resistance matching within 2Ω, which helps preserve balance when the same conversion or amplifier stage handles the selected signal. A typical circuit connects each common terminal to a precision ADC input and places the two sensor sources on the switched terminals. The 175ns turn-on and 100ns turn-off times are short compared with most sensor sampling periods, but the design must allow the output node to settle after each transition. This arrangement is useful for redundant sensors, selectable thermistors, and factory calibration inputs where keeping the analog front end unchanged is valuable.
Recomendado
Precision Test and Measurement Routing
The MAX383CPE+ is useful in test systems that route one instrument or measurement channel to either of two inputs. Its two integrated SPDT switches reduce the number of separate packages and can maintain closely matched resistance between channels, with the manufacturer specifying less than 35Ω on-resistance and matching within 2Ω. The 3V to 15V supply range permits operation from a low-voltage bench system, while the 16-pin PDIP package is convenient for legacy or prototype fixtures. Engineers should use the common, normally open, and normally closed terminals exactly as shown in the data-sheet pin configuration and account for charge injection when the source impedance is high.
Recomendado
Battery-Powered Data Acquisition
The MAX383CPE+ fits low-voltage battery-powered acquisition systems because it operates from 3V to 15V and supports dual supplies from ±3V to ±8V. Two SPDT channels can select between external inputs and internal calibration or reference paths without introducing a separate multiplexer package. The specified turn-on and turn-off times of 175ns and 100ns support rapid routing, although overall acquisition speed is more likely to be limited by the sensor and converter. Low-power designs should include the control logic in their power budget and verify the device's operating current under the selected switching state using the manufacturer electrical characteristics.
Recomendado
Bipolar Analog Signal Multiplexing
For bipolar instrumentation signals, the MAX383CPE+ can operate from dual supplies spanning ±3V to ±8V. Each SPDT channel routes its common terminal to either a normally closed or normally open input, allowing positive and negative signal sources to be presented to a shared downstream amplifier or converter. The matched on-resistance of the two channels, guaranteed within 2Ω, helps preserve differential or complementary signal balance. Because the switch adds resistance and introduces charge injection, precision designs should include the on-resistance in the signal-loss budget and validate settling time at the highest expected input impedance.
Recomendado
Sample-and-Hold Signal Routing
A MAX383CPE+ SPDT channel can connect a source to a sample-and-hold capacitor or to a different discharge path, allowing the same acquisition circuit to select which signal is captured. The 100ns turn-off and 175ns turn-on specifications establish the device's switching contribution, while the less-than-35Ω on-resistance limits voltage attenuation from the source. The exact acquisition interval must also include amplifier settling, capacitor charging, leakage, and switch charge injection. For high-value sampling capacitors, keep the common and switched traces short and verify leakage limits in the manufacturer data sheet before finalizing the layout.
Recomendado
Industrial Control Signal Multiplexing
The MAX383CPE+ can select between two control or measurement paths in a compact industrial circuit while operating from 3V to 15V. Its commercial temperature specification of 0°C to +70°C is suitable for indoor or temperature-controlled equipment; extended-temperature requirements should use an appropriate MAX383 grade. The two SPDT channels allow independent routing within one package, while the through-hole PDIP-16 format supports repair and prototype assembly. Designers should define logic states when control inputs can float, protect signal pins from conditions beyond the manufacturer ratings, and place the device where through-hole lead stress and contamination are controlled.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MAX383CPE+ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX383EPE+ | MAX383APE+ | MAX383CPE | MAX383CPE++ | MAX383EPE |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Switch Configuration | 2 x SPDT | 2 x SPDT | 2 x SPDT | 2 x SPDT | 2 x SPDT | 2 x SPDT |
| On-Resistance | Less than 35Ω | Less than 35Ω | Less than 35Ω | Less than 35Ω | Less than 35Ω | Less than 35Ω |
| Supply Voltage Range | 3V to 15V | 3V to 15V | 3V to 15V | 3V to 15V | 3V to 15V | 3V to 15V |
| Dual Supply Voltage Range | ±3V to ±8V | ±3V to ±8V | ±3V to ±8V | ±3V to ±8V | ±3V to ±8V | ±3V to ±8V |
| Turn-On Time | 175ns | 175ns | 175ns | 175ns | 175ns | 175ns |
| Turn-Off Time | 100ns | 100ns | 100ns | 100ns | 100ns | 100ns |
| Operating Temperature Range | 0°C to +70°C | Extended temperature grade | Extended temperature grade | 0°C to +70°C | 0°C to +70°C | Extended temperature grade |
Diferenciadores clave
- Two independently selectable SPDT channels in one package (frente a MAX381CPE+)
- Independent routing rather than paired double-pole switching (frente a MAX385CPE+)
- Matched channel resistance (frente a MAX383CPE)
- Through-hole assembly compatibility (frente a MAX383ESE+)
Notas de diseño
Treat the MAX383 as a resistance in the signal path rather than an ideal switch. With on-resistance specified below 35Ω, attenuation becomes significant when the source impedance is high. Calculate the divider formed by the source and switch resistance, and include the input impedance of the following amplifier or converter. For precision paths, use both channels consistently because the manufacturer guarantees on-resistance matching within 2Ω.
Do not assume that the two SPDT channels switch simultaneously. The MAX383 provides two independent selectors, so control timing and post-switch settling must be coordinated when paired signals must arrive together. Allow the downstream circuit to settle after each transition, especially with high source impedance, long PCB traces, or large capacitance. Use the manufacturer timing and charge-injection characteristics when defining the acquisition interval.
Place the PDIP-16 device close to the routed signals to minimize trace capacitance and susceptibility to coupled noise. Keep the analog common and switched paths away from high-current switching nodes and clocks. Provide a low-impedance ground and supply return, decouple the supply according to the manufacturer recommendations, and use defined logic levels for control inputs so the switch cannot enter an indeterminate state during reset.
Operate the device only within its specified 3V to 15V supply range, or use a supported dual supply from ±3V to ±8V. Verify control-logic levels against the selected supply arrangement and include the MAX383 supply current in the system power budget. If an input can exceed the supply rails, add external protection or isolation rather than assuming the analog switch will tolerate the overvoltage.
Información de cumplimiento
The + ordering suffix identifies an ordering variant, but no explicit RoHS, REACH, halogen-free, or conflict-minerals statement was present in the accessible manufacturer page. Compliance must be confirmed for the exact assembled ordering code from the manufacturer's product documentation.