MAX383CPE+ - Dual SPDT 35Ω Analog Switch | Analog Devices
MPN: MAX383CPE+ ✓ 啟用中MAX383CPE+ 概覽
An analog switch is an electronic routing device that connects one signal terminal to one of two alternatives under digital control. A single-pole double-throw switch, or SPDT, has one common terminal and two switched terminals. The MAX383 places two SPDT switches in one 16-pin package, placing it in the hierarchy of CMOS analog switches, analog multiplexers, interface ICs, and semiconductor signal-routing components.
Each MAX383 channel has one normally open and one normally closed path. According to the manufacturer product page, the on-resistance is less than 35Ω, channel matching is guaranteed within 2Ω, and the resistance remains flat over the operating signal range. These characteristics make the matched channels useful when amplitude accuracy across a dual-channel path is more important than minimizing resistance absolutely.
The MAX383 family supports both single-supply and dual-supply operation. Its specified turn-on and turn-off times are 175ns and 100ns, respectively, enabling controlled signal routing with relatively little transition delay. The low-voltage CMOS implementation is suited to battery-powered, industrial control, instrumentation, and test-equipment systems where low-voltage logic and analog signals share the same board.
Typical uses include selecting between two sensor channels, routing test signals, switching bipolar or unipolar analog inputs, and implementing sample-and-hold paths. Two integrated SPDT switches can route complementary or paired signals while keeping channel timing and resistance characteristics closely matched.
Designers should maintain the specified 3V to 15V supply range, use pull-up or pull-down resistors where control or common-pin states require defined levels, and account for charge injection and off-state leakage when switching high-impedance or precision measurement circuits. The through-hole PDIP-16 package also simplifies prototype assembly and legacy PCB maintenance.
This page combines manufacturer specifications, matched-channel design guidance, sourcing information, package details, and same-family replacement analysis to support practical analog-switch selection beyond a basic distributor parameter summary.
直接替換替代品,適用於 MAX383CPE+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MAX383EPE+
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX383APE+
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX383CPE
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX383CPE++
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX383EPE
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX383CPE+ 最大額定值與電氣特性
| Number of Switches | 2 |
| Number of Channels | 2 |
| Switch Configuration | 2 x SPDT |
| On-Resistance | Less than 35Ω |
| Channel Resistance Matching | Within 2Ω |
| Supply Voltage Range | 3V to 15V |
| Dual Supply Voltage Range | ±3V to ±8V |
| Turn-On Time | 175ns |
| Turn-Off Time | 100ns |
| 工作溫度範圍 | 0°C to +70°C |
| Temperature Grade | Commercial |
| 封裝 | PDIP-16 |
| Number of Terminals | 16 |
| 安裝類型 | Through Hole |
| Packaging | Tube |
| Switch Type | Normally Open and Normally Closed Poles |
| RoHS 狀態 | unknown |
MAX383CPE+ pdip-16 腳位配置指南
MAX383CPE+(pdip-16 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX383CPE+.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX383CPE+ 適用於 6 應用s: Sensor Signal Selection, Precision Test and Measurement Routing, Battery-Powered Data Acquisition, Bipolar Analog Signal Multiplexing, Sample-and-Hold Signal Routing, Industrial Control Signal Multiplexing.
Sensor Signal Selection
The MAX383CPE+ can select between two sensor outputs through its two independent SPDT channels while maintaining less than 35Ω on-resistance. The manufacturer guarantees channel resistance matching within 2Ω, which helps preserve balance when the same conversion or amplifier stage handles the selected signal. A typical circuit connects each common terminal to a precision ADC input and places the two sensor sources on the switched terminals. The 175ns turn-on and 100ns turn-off times are short compared with most sensor sampling periods, but the design must allow the output node to settle after each transition. This arrangement is useful for redundant sensors, selectable thermistors, and factory calibration inputs where keeping the analog front end unchanged is valuable.
推薦
Precision Test and Measurement Routing
The MAX383CPE+ is useful in test systems that route one instrument or measurement channel to either of two inputs. Its two integrated SPDT switches reduce the number of separate packages and can maintain closely matched resistance between channels, with the manufacturer specifying less than 35Ω on-resistance and matching within 2Ω. The 3V to 15V supply range permits operation from a low-voltage bench system, while the 16-pin PDIP package is convenient for legacy or prototype fixtures. Engineers should use the common, normally open, and normally closed terminals exactly as shown in the data-sheet pin configuration and account for charge injection when the source impedance is high.
推薦
Battery-Powered Data Acquisition
The MAX383CPE+ fits low-voltage battery-powered acquisition systems because it operates from 3V to 15V and supports dual supplies from ±3V to ±8V. Two SPDT channels can select between external inputs and internal calibration or reference paths without introducing a separate multiplexer package. The specified turn-on and turn-off times of 175ns and 100ns support rapid routing, although overall acquisition speed is more likely to be limited by the sensor and converter. Low-power designs should include the control logic in their power budget and verify the device's operating current under the selected switching state using the manufacturer electrical characteristics.
推薦
Bipolar Analog Signal Multiplexing
For bipolar instrumentation signals, the MAX383CPE+ can operate from dual supplies spanning ±3V to ±8V. Each SPDT channel routes its common terminal to either a normally closed or normally open input, allowing positive and negative signal sources to be presented to a shared downstream amplifier or converter. The matched on-resistance of the two channels, guaranteed within 2Ω, helps preserve differential or complementary signal balance. Because the switch adds resistance and introduces charge injection, precision designs should include the on-resistance in the signal-loss budget and validate settling time at the highest expected input impedance.
推薦
Sample-and-Hold Signal Routing
A MAX383CPE+ SPDT channel can connect a source to a sample-and-hold capacitor or to a different discharge path, allowing the same acquisition circuit to select which signal is captured. The 100ns turn-off and 175ns turn-on specifications establish the device's switching contribution, while the less-than-35Ω on-resistance limits voltage attenuation from the source. The exact acquisition interval must also include amplifier settling, capacitor charging, leakage, and switch charge injection. For high-value sampling capacitors, keep the common and switched traces short and verify leakage limits in the manufacturer data sheet before finalizing the layout.
推薦
Industrial Control Signal Multiplexing
The MAX383CPE+ can select between two control or measurement paths in a compact industrial circuit while operating from 3V to 15V. Its commercial temperature specification of 0°C to +70°C is suitable for indoor or temperature-controlled equipment; extended-temperature requirements should use an appropriate MAX383 grade. The two SPDT channels allow independent routing within one package, while the through-hole PDIP-16 format supports repair and prototype assembly. Designers should define logic states when control inputs can float, protect signal pins from conditions beyond the manufacturer ratings, and place the device where through-hole lead stress and contamination are controlled.
推薦
推薦產品摘要
工程參考資料,適用於 MAX383CPE+ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX383EPE+ | MAX383APE+ | MAX383CPE | MAX383CPE++ | MAX383EPE |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Switch Configuration | 2 x SPDT | 2 x SPDT | 2 x SPDT | 2 x SPDT | 2 x SPDT | 2 x SPDT |
| On-Resistance | Less than 35Ω | Less than 35Ω | Less than 35Ω | Less than 35Ω | Less than 35Ω | Less than 35Ω |
| Supply Voltage Range | 3V to 15V | 3V to 15V | 3V to 15V | 3V to 15V | 3V to 15V | 3V to 15V |
| Dual Supply Voltage Range | ±3V to ±8V | ±3V to ±8V | ±3V to ±8V | ±3V to ±8V | ±3V to ±8V | ±3V to ±8V |
| Turn-On Time | 175ns | 175ns | 175ns | 175ns | 175ns | 175ns |
| Turn-Off Time | 100ns | 100ns | 100ns | 100ns | 100ns | 100ns |
| Operating Temperature Range | 0°C to +70°C | Extended temperature grade | Extended temperature grade | 0°C to +70°C | 0°C to +70°C | Extended temperature grade |
主要差異化特點
- Two independently selectable SPDT channels in one package (對比MAX381CPE+)
- Independent routing rather than paired double-pole switching (對比MAX385CPE+)
- Matched channel resistance (對比MAX383CPE)
- Through-hole assembly compatibility (對比MAX383ESE+)
設計說明
Treat the MAX383 as a resistance in the signal path rather than an ideal switch. With on-resistance specified below 35Ω, attenuation becomes significant when the source impedance is high. Calculate the divider formed by the source and switch resistance, and include the input impedance of the following amplifier or converter. For precision paths, use both channels consistently because the manufacturer guarantees on-resistance matching within 2Ω.
Do not assume that the two SPDT channels switch simultaneously. The MAX383 provides two independent selectors, so control timing and post-switch settling must be coordinated when paired signals must arrive together. Allow the downstream circuit to settle after each transition, especially with high source impedance, long PCB traces, or large capacitance. Use the manufacturer timing and charge-injection characteristics when defining the acquisition interval.
Place the PDIP-16 device close to the routed signals to minimize trace capacitance and susceptibility to coupled noise. Keep the analog common and switched paths away from high-current switching nodes and clocks. Provide a low-impedance ground and supply return, decouple the supply according to the manufacturer recommendations, and use defined logic levels for control inputs so the switch cannot enter an indeterminate state during reset.
Operate the device only within its specified 3V to 15V supply range, or use a supported dual supply from ±3V to ±8V. Verify control-logic levels against the selected supply arrangement and include the MAX383 supply current in the system power budget. If an input can exceed the supply rails, add external protection or isolation rather than assuming the analog switch will tolerate the overvoltage.
合規資訊
The + ordering suffix identifies an ordering variant, but no explicit RoHS, REACH, halogen-free, or conflict-minerals statement was present in the accessible manufacturer page. Compliance must be confirmed for the exact assembled ordering code from the manufacturer's product documentation.