Microchip Technology

MCP6022-E/ST - 10MHz Dual RRO Amplifier | Microchip

N.º de pieza: MCP6022-E/ST ✓ Activo
<0.5 mV typical Vdss 1.0 mA Id 8-TSSOP, 4.40 mm width Package
MOQ: 1 |

MCP6022-E/ST Descripción general

The Microchip Technology MCP6022-E/ST is a dual operational amplifier with a 10 MHz gain-bandwidth product, typical operating current of 1.0 mA per amplifier, input offset voltage below 0.5 mV, and an 8-pin TSSOP package. The device uses advanced CMOS technology to provide low bias current, high open-loop gain, rail-to-rail input and output operation, and low distortion.

An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its two inputs. The MCP6022 combines two amplifiers in one package, making it suitable for dual-channel signal paths. Its rail-to-rail input and output characteristics help preserve signal range in systems operating from a single low-voltage supply, where input and output common-mode limits are important design constraints.

The principal features of the MCP6022 include 10 MHz gain-bandwidth product, 8.7 nV/√Hz input noise, less than 0.5 mV typical input offset voltage, and 0.00053% THD+N distortion. Low power consumption makes it appropriate for portable instrumentation, while the 10 MHz bandwidth supports audio, filtering, sensing, and general-purpose analog signal conditioning.

The MCP6022 uses rail-to-rail input and output stages to extend usable input and output range toward the supply rails. Its CMOS architecture supports low bias current and low operating current, helping reduce loading on high-impedance sensors and reducing power demand in battery-powered systems. The two amplifiers can be configured independently for gain, filtering, buffering, or differential signal conditioning.

Typical applications include low-noise sensor interfaces, audio preamplification, active filters, data-acquisition signal conditioning, portable measurement systems, and general dual-amplifier circuits. The combination of low noise, 10 MHz bandwidth, rail-to-rail operation, and a compact TSSOP-8 package makes the MCP6022 useful where two precision analog channels are required on a space-constrained PCB.

Designers should review the manufacturer pin-description table and typical application circuit before assigning tracks. Input and output stability must be evaluated with the selected feedback network, source impedance, load, supply voltage, and decoupling capacitors. Care is also required when driving capacitive loads or operating near the limits of the rail-to-rail input and output ranges.

This page combines manufacturer specifications, practical circuit guidance, package and pin information, and qualified drop-in alternatives to support design selection and PCB reuse. It also provides a parameter-level comparison for engineers evaluating temperature-grade, automotive, and low-power family options.

Alternativas directas para MCP6022-E/ST — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con MCP6022-E/ST (mismo factor de forma y huella) — difiere en Amplifier Type, Package, Typical Operating Current, Input Offset Voltage, Gain-Bandwidth Product.

Microchip Technology
Amplifier Type: Single operational amplifier
Package: 8-pin TSSOP
Microchip Technology
Package: 8-lead TSSOP
Typical Operating Current: 1.0 mA per amplifier
Input Offset Voltage: Less than 0.5 mV
Microchip Technology
Amplifier Type: General-purpose CMOS operational amplifier
Package: 8-pin TSSOP
Typical Operating Current: 230 uA

MCP6022-I/ST

✅ Sustitución directa ⚠️ Especificaciones sin verificar
Microchip Technology
📦 8-TSSOP
Dual general-purpose operational amplifier · 2 amplifiers · 10 MHz · 1.0 mA per amplifier · Less than 1.35 mA per amplifier · Less than 0.5 mV · 2.5 V · Rail-to-rail

Consulte el precio

Ver hoja de datos →

MCP6022-E/VAO

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 8-TSSOP
Automotive-qualified ordering option in the same 8-TSSOP footprint; qualification status and grade-specific electrical limits differ from the standard MCP6022-E/ST

📋 Alternativa de referencia (no en el catálogo)

MCP6023-E/ST

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 8-TSSOP
Lower-power MCP602x dual amplifier in the same 8-TSSOP footprint; operating current is lower than 1.0 mA typical, while noise, offset, and dynamic performance require comparison

📋 Alternativa de referencia (no en el catálogo)

MCP6022-E/ST Valores máximos y características eléctricas

Amplifier Type Dual general-purpose operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 10 MHz
Typical Operating Current 1.0 mA
Input Offset Voltage <0.5 mV typical
Input Noise Density 8.7 nV/√Hz
Total Harmonic Distortion plus Noise 0.00053% THD+N
Output Swing Rail-to-rail output
Single-Supply Operation Supported
Encapsulado 8-TSSOP, 4.40 mm width
Tipo de montaje Surface mount

Configuración de pines de MCP6022-E/ST

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
Pin 1 OUTA — Amplifier A output
Pin 2 IN-A — Inverting input for amplifier A
Pin 3 IN+A — Non-inverting input for amplifier A
Pin 4 V- — Negative supply connection
Pin 5 IN+B — Non-inverting input for amplifier B
Pin 6 IN-B — Inverting input for amplifier B
Pin 7 OUTB — Amplifier B output
Pin 8 V+ — Positive supply connection

Aplicaciones típicas

MCP6022-E/ST es adecuado para 6 aplicacións: Precision Sensor Signal Conditioning, Active Audio Preamplification, Precision Active Filtering, Portable Data Acquisition, Industrial Control Signal Interfaces, Audio Amplifier and Filter Integration.

🧩

Precision Sensor Signal Conditioning

The MCP6022-E/ST fits low-level sensor front ends requiring two amplified channels, low input noise of 8.7 nV/√Hz, and input offset voltage below 0.5 mV typical. Each amplifier can provide gain and buffering ahead of an ADC or measurement controller while drawing a typical 1.0 mA operating current. Rail-to-rail input operation increases the usable signal range in compact single-supply systems. The 10 MHz gain-bandwidth product also supports closed-loop gains where adequate phase margin and stability must be maintained.

🎧

Active Audio Preamplification

The MCP6022-E/ST is suitable for dual-channel audio preamplification because it combines a 10 MHz gain-bandwidth product with 0.00053% THD+N and rail-to-rail output operation. The two amplifiers can process left and right channels independently, while the low typical operating current of 1.0 mA supports compact and portable audio products. Input and output loading must remain within the manufacturer limits, and the chosen gain network should preserve stability with the source impedance and cable capacitance.

🔧

Precision Active Filtering

The MCP6022-E/ST can implement first- and higher-order active filters where two channels are convenient. Its 10 MHz gain-bandwidth product provides bandwidth headroom beyond many audio-band filter requirements, while input offset voltage below 0.5 mV typical helps preserve low-level signals. The two amplifiers may also form a state-variable or multiple-feedback section. Component tolerances, gain-bandwidth behavior, output loading, and bypass placement should be evaluated together for stable operation.

📱

Portable Data Acquisition

The MCP6022-E/ST is appropriate for portable data-acquisition front ends where two analog channels must be conditioned before digitization. The 1.0 mA typical operating current reduces demand on battery-powered systems, while the low-noise specification supports measurement of small sensor outputs. Rail-to-rail input and output behavior is useful when the converter and sensor operate near a low-voltage supply rail. Supply bypass should be placed close to pins 4 and 8, with layout designed to minimize noise pickup.

🏭

Industrial Control Signal Interfaces

The MCP6022-E/ST can condition low-level control and feedback signals in industrial equipment when the system needs two independent analog channels in a compact footprint. Its rail-to-rail operation supports single-supply interface design, and the 10 MHz bandwidth is adequate for many control, monitoring, and sensor-loop functions. The TSSOP-8 package simplifies high-density routing, although industrial temperature-grade requirements may favor MCP6022-I/ST. Grounding, isolation boundaries, and protection devices remain important system-level design considerations.

🔊

Audio Amplifier and Filter Integration

The MCP6022-E/ST can place filtering and gain-control functions close to a high-performance audio converter. Its low distortion, 10 MHz bandwidth, and dual-channel configuration support stereo signal paths, while low typical operating current benefit space-constrained systems. Place decoupling and ground-return paths carefully to avoid coupling converter switching noise into the analog input. The output drive capability must be checked against the selected audio codec and any downstream filtering network before the circuit is finalized.

What are the key specifications of MCP6022-E/ST that engineers should know?
The MCP6022-E/ST is a dual, 10 MHz operational amplifier in an 8-TSSOP package with a typical operating current of 1.0 mA and input offset voltage below 0.5 mV. According to the Microchip manufacturer datasheet, it also provides 8.7 nV/√Hz input noise, rail-to-rail input and output operation, and 0.00053% THD+N. These characteristics make it appropriate for dual-channel precision signal conditioning, active filtering, sensor interfaces, and low-power portable equipment.
Where can I download the MCP6022-E/ST datasheet PDF?
The MCP6022-E/ST datasheet and product documentation are available through the official Microchip MCP6022 product page at https://www.microchip.com/en-us/product/MCP6022. The manufacturer datasheet contains the electrical characteristics, typical application circuits, pin descriptions, and ordering information needed for design review. Search the product page for the current MCP6022 datasheet PDF and revision, and use that document as the controlling reference for supply limits, stability, and package drawings.
Where can I find the MCP6022-E/ST pinout and TSSOP-8 pin description?
The MCP6022-E/ST uses an 8-pin TSSOP package with two independent operational amplifiers. According to the Microchip manufacturer pin-description table, pins 1, 2, and 3 belong to amplifier A, pins 5, 6, and 7 belong to amplifier B, and pins 4 and 8 provide the negative and positive supplies. Use the pin table in the manufacturer datasheet when assigning PCB tracks and confirming the exposed package orientation.
What is the MCP6022 op amp and what is it used for?
The MCP6022 is a dual CMOS operational amplifier designed for low-power signal conditioning at bandwidths up to 10 MHz. It provides two amplifiers, rail-to-rail input and output behavior, input noise of 8.7 nV/√Hz, and typical operating current of 1.0 mA according to the Microchip manufacturer datasheet. Typical uses include buffering sensor outputs, implementing active filters, amplifying audio signals, and conditioning inputs for measurement or conversion systems.
What is the difference between MCP6022 and MCP6002?
The MCP6022 provides a 10 MHz gain-bandwidth product and 8.7 nV/√Hz input noise, making it more suited to higher-bandwidth and lower-noise signal paths than the MCP6002 family. The MCP6002 is commonly associated with lower-frequency, low-power general-purpose amplification, while the MCP6022 is the higher-performance member of Microchip's CMOS amplifier family. Verify package, supply voltage, and exact AC specifications in the manufacturer datasheet before substituting one device for the other.
MCP6022 vs MCP6023 - which is better for a low-power application?
Choose the MCP6022 when the design benefits from its 10 MHz gain-bandwidth product and typical 1.0 mA operating current. The MCP6023 is the lower-power member of the family, so it is generally preferable when minimum supply current is more important than bandwidth. Both are dual rail-to-rail CMOS amplifiers in the MCP602x family, but exact supply current, offset, noise, and temperature-grade limits should be compared against the manufacturer datasheet for the selected ordering code.
When should I choose MCP6022-E/ST over another dual CMOS op amp?
Choose MCP6022-E/ST when the circuit needs two independent channels, a 10 MHz gain-bandwidth product, rail-to-rail input and output operation, and low noise in a compact TSSOP-8 package. It is particularly suitable for filtering, low-level sensor conditioning, and portable analog measurement. Select a different family member when low-power operation, automotive qualification, exact offset limits, or a different package is more important than the MCP6022's combination of bandwidth and operating current.
Is MCP6022-E/ST suitable for audio and sensor-interface applications?
The MCP6022-E/ST is suitable for audio preamplification and precision sensor-interface circuits. Its 10 MHz gain-bandwidth product provides useful bandwidth for low-frequency audio and measurement paths, while 8.7 nV/√Hz input noise supports low-amplitude signal handling. The 0.00053% THD+N figure also indicates low distortion. Confirm output swing, load capability, and stability with the actual gain, load, supply, and bypass configuration.
What is the best drop-in replacement for MCP6022-E/ST?
The closest same-package options are the MCP6022-I/ST temperature-grade variant, the automotive MCP6022-E/VAO variant, and the lower-power MCP6023-E/ST dual amplifier. Pin compatibility must be confirmed against the manufacturer pin-description table for each ordering code. No cross-brand drop-in equivalent was established from the available technical cross-reference material, so board changes should not be assumed when evaluating these alternatives.
Can MCP6023-E/ST replace MCP6022-E/ST on the same PCB?
The MCP6023-E/ST can be considered for a footprint-compatible design because it is a dual amplifier in the same TSSOP-8 family, but it is not a specification-identical substitute. Its defining feature is lower operating current, so bandwidth, offset, noise, slew rate, and load behavior must be checked against the MCP6022 requirements. The MCP6022 remains preferable when its 1.0 mA typical operating current and 10 MHz bandwidth are the required targets.
What can replace MCP6022-E/ST?
A replacement must satisfy three constraints: the same TSSOP-8 pin arrangement, compatible supply-voltage operation, and adequate bandwidth, noise, offset, output swing, and stability for the circuit. The MCP6022-I/ST and MCP6022-E/VAO provide same-package qualification options, while the MCP6023-E/ST provides a lower-power functional choice. Treat each as an engineering substitution rather than an automatic drop-in and verify the manufacturer datasheet before releasing production artwork.
Is MCP6022-E/ST the same as MCP6022T-E/ST?
The MCP6022T-E/ST listing identifies the same MCP6022 dual rail-to-rail amplifier and 8-TSSOP package, but the added ordering code generally denotes a different reel or tape packaging format. For PCB substitution, the electrical function and pinout are more important than the shipment format, but procurement should use the exact approved ordering code to avoid assembly and labeling errors. Both references identify a 10 MHz, two-circuit amplifier.
Where can I buy MCP6022-E/ST online and what is its price?
Use the Request a Quote form on this page to request current MCP6022-E/ST availability, unit pricing, and lead time. The form allows procurement to specify the required quantity and shipment details without relying on a static, potentially stale price. The device is listed by the manufacturer as a general-purpose dual operational amplifier, and the exact ordering code includes the 8-TSSOP package and manufacturer grade suffix.
What is the lead time and stock status for MCP6022-E/ST?
Current stock, minimum order quantity, and lead time for MCP6022-E/ST should be requested through the Request a Quote form on this page. Availability can vary with the exact ordering code, reel format, and order quantity, so a historical listing should not be treated as a current allocation. For production planning, confirm the lot-traceability requirements, delivery schedule, and packaged quantity with the supplier response.
Does MCP6022-E/ST comply with RoHS and REACH?
The MCP6022-E/ST compliance status should be confirmed for the exact ordering code using Microchip's product documentation and material-compliance declarations. RoHS and REACH are separate material restrictions, and the presence of a -E ordering suffix does not by itself establish either status. Request the current manufacturer compliance statement and applicable declarations when a regulated design requires documentary proof.

Datos de referencia de ingeniería para MCP6022-E/ST — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose MCP6022-E/ST for a general-purpose dual analog channel that combines a 10 MHz gain-bandwidth product, 8.7 nV/√Hz input noise, input offset voltage below 0.5 mV typical, and a typical operating current of 1.0 mA. Choose MCP6022-I/ST when the same electrical family and TSSOP-8 footprint are needed with an industrial temperature-grade ordering option. Choose MCP6022-E/VAO for designs requiring an automotive-qualified MCP6022 variant. Choose MCP6023-E/ST when minimum current consumption is the dominant objective and lower bandwidth or other dynamic limits are acceptable. No cross-brand drop-in substitute was established, so a cross-manufacturer replacement should not be assumed without a fresh pinout, supply, noise, offset, stability, and lifecycle review.

Comparación con alternativas

Parámetro Este producto MCP6022-I/ST MCP6022-E/VAO MCP6023-E/ST
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-TSSOP 8-TSSOP 8-TSSOP 8-TSSOP
Number of Amplifiers 2 2 2 2
Typical Operating Current 1.0 mA 1.0 mA 1.0 mA Lower-power family variant
Input and Output Operation Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output
Qualification Focus General-purpose grade Industrial temperature grade Automotive-qualified option General-purpose low-power option

Diferenciadores clave

  • Combines dual-channel amplification with 10 MHz bandwidth (frente a MCP6023-E/ST)
  • Provides a temperature-grade option without changing the footprint (frente a MCP6022-I/ST)
  • Offers an automotive-qualified family option (frente a MCP6022-E/VAO)

Notas de diseño

Place the supply bypass capacitor immediately between pins 4 and 8, with a short, low-impedance return path to the device ground connection. Keep amplifier input and feedback tracks away from the bypass-current loop and other high-current switching paths. Because the MCP6022-E/ST uses an 8-TSSOP package, the exposed pads of adjacent components and the narrow lead spacing require careful solder-mask and paste control.

Evaluate feedback-network values against the 10 MHz gain-bandwidth product rather than selecting them from the nominal gain alone. Low source impedances and capacitive loads can reduce phase margin, particularly at higher closed-loop gains. If the source has appreciable capacitance, add series isolation resistance and verify the complete circuit with the manufacturer's stability guidance or a simulation using the available device model.

Do not assume rail-to-rail input and output operation guarantees usable output swing exactly at the supply rails. Leave the required input common-mode and output headroom for the selected supply voltage and load. Also verify that each amplifier has an appropriate feedback path to its corresponding inverting input and that unused channels are configured according to the manufacturer recommendations.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

Compliance declarations for the exact MCP6022-E/ST ordering code are not stated in the available technical material. Confirm current RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification documents with Microchip before regulatory submission.

Búsquedas relacionadas

mcp6022 datasheet mcp6022 pinout mcp6022 op amp mcp6022 vs mcp6002 mcp6022 price mcp6022 pdf mcp6022 equivalent MCP6022-E/ST datasheet MCP6022-E/ST pinout MCP6022-E/ST replacement MCP6022-E/ST drop-in substitute Microchip MCP6022-E/ST

Componentes & términos relacionados

Microchip Technology MCP6022-E/ST MCP6022 MCP6022-I/ST MCP6022-E/VAO MCP6023-E/ST operational amplifier dual operational amplifier analog signal conditioning CMOS rail-to-rail input rail-to-rail output gain-bandwidth product input noise density input offset voltage THD+N low-power electronics active filter sensor interface audio preamplifier 8-TSSOP TSSOP package family surface-mount device single-supply operation
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ