MPC8548VJATGD - PowerQUICC III e500 MPU 1.2GHz 783-FCBGA | NXP
N.º de pieza: MPC8548VJATGD ✓ ActivoMPC8548VJATGD Descripción general
An embedded microprocessor, also referred to as a microprocessor unit (MPU) or communications processor, integrates a CPU core, memory controllers, and peripheral interfaces on a single die. The MPC85xx family extends the PowerQUICC architecture (PowerQUICC -> communications SoC -> application-specific MPU) used in routers, base stations, and storage area network equipment. Compared with general-purpose microcontrollers, these MPUs emphasise high-throughput serial interfaces, deterministic interrupt latency, and hardware-accelerated communications blocks.
Key features include an e500 core with 36-bit physical addressing, 512 KB of L2 cache (configurable as SRAM), dual integrated DDR2 memory controllers supporting up to 600 MHz data rate, four Gigabit Ethernet MACs (two SGMII, two RGMII), two PCI Express interfaces, two RapidIO interfaces, two USB 2.0 controllers, and a security engine. The integrated DDR2 controller eliminates external memory bridge ICs and reduces BOM cost for high-throughput embedded systems.
Architecture depth: the e500 core implements Book-E architecture extensions, dual-issue superscalar pipeline, and hardware table-walk for virtualisation-aware systems. The 90 nm process node achieves the 1.2 GHz operating frequency while keeping typical core power within 8 W, suitable for fan-cooled chassis. The integrated security engine accelerates IPSec, SSL/TLS, SRTP, and 3GPP cipher suites, offloading packet processing from the core and improving aggregate system throughput.
Typical applications include multiservice routers, enterprise switches, line cards for wireless base stations, network-attached storage controllers, and industrial control modules. The high integration enables compact line-card designs with reduced component count, while the dual Ethernet and PCI Express lanes allow direct attachment of PHY devices and switch fabrics.
When designing with this MPU, ensure adequate thermal management - the 783-FCBGA package dissipates several watts under sustained load, and a minimum four-layer PCB with dedicated power and ground planes is required to meet signal-integrity targets for DDR2 and Gigabit Ethernet. Designers should also validate RapidIO or PCI Express SerDes reference clock jitter against the requirements in the NXP hardware specification.
This page consolidates distributor pricing, drop-in same-package alternatives, and practical design guidance beyond what the manufacturer datasheet provides, giving engineers a single resource for evaluation, sourcing, and second-source planning.
Alternativas directas para MPC8548VJATGD — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MPC8548VJATGD (mismo factor de forma y huella) — difiere en Ethernet, Manufacturer, Memory Controller, Operating Temperature, Package.
MPC8548PXATGD
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MPC8548VJAUQD
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MPC8548ECVJATGD
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MPC8548EVJATGD
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MPC8548VJAQGD
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MPC8548VJANGD
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
MPC8548VJATGD Valores máximos y características eléctricas
| Manufacturer | NXP Semiconductors |
| Series | MPC85xx / PowerQUICC III |
| Core Architecture | PowerPC e500 |
| Number of Cores | 1 |
| Ancho del bus de datos | 32-bit |
| Maximum Core Frequency | 1.2 GHz |
| Encapsulado | 783-FCBGA (29x29 mm) |
| Tipo de montaje | Surface Mount |
| L2 Cache | 512 KB |
| Memory Controller | Dual DDR2 (up to 600 MHz) |
| Ethernet | 4x Gigabit (2x SGMII + 2x RGMII) |
| PCI Express | 2 lanes |
| RapidIO | 2 interfaces |
| USB | 2x USB 2.0 |
| Tensión de alimentación de funcionamiento | 1.8 V / 2.5 V / 3.3 V |
| Process Node | 90 nm |
| Temperatura de funcionamiento | -40C to +105C |
| Lead Free / RoHS | Yes (Lead-free per Mouser listing) |
Guía de configuración de pines de MPC8548VJATGD 783-fcbga (29x29 mm)
Configuración de pines para MPC8548VJATGD (encapsulado 783-fcbga (29x29 mm)). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para MPC8548VJATGD.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
MPC8548VJATGD es adecuado para 6 aplicacións: Multiservice Router / Branch Office Gateway, Wireless Base Station Line Card, Enterprise Network Switch Control Plane, Network-Attached Storage (NAS) Controller, Industrial Edge Controller / Soft PLC, Printer/MFP Controller Board.
Multiservice Router / Branch Office Gateway
The MPC8548VJATGD's 1.2 GHz e500 core plus dual DDR2 controllers and four Gigabit Ethernet MACs make it ideal for small-to-medium enterprise routers and VPN gateways. The integrated security engine accelerates IPSec, SSL/TLS, and 3GPP cipher suites, offloading crypto from the main CPU and pushing aggregate encrypted throughput above 1 Gbps for typical IPsec-AES128 traffic. Place the MPU between PHY transceivers (SGMII/RGMII) and the WAN modem module with 16-bit DDR2-800 ECC memory for buffer pools. The 783-FCBGA footprint enables fan-cooled fanless chassis designs with sufficient copper for the 1.2 GHz power envelope, while the four SERDES lanes support direct attachment of multi-port Ethernet PHYs without external switches.
Recomendado
Wireless Base Station Line Card
The MPC8548VJATGD's PCI Express and RapidIO interfaces suit it for base-station line cards where it terminates Layer 2 traffic and feeds baseband DSPs via SRIO. Its deterministic interrupt latency and dual DDR2 controllers provide the bandwidth headroom required for LTE/HSPA+ MAC scheduling. Place the MPU alongside TI TMS320C66x DSPs via x1 PCIe, with four SERDES lanes and one RapidIO port for backhaul. The 783-FCBGA thermal envelope (operating up to +105C) supports outdoor base-station chassis without derating, while the security engine accelerates SRTP cipher suites for voice-data confidentiality.
Recomendado
Enterprise Network Switch Control Plane
The MPC8548VJATGD serves as the control-plane CPU on managed Layer 2/3 enterprise switches, handling routing tables, ACL updates, SNMP, and CLI management while the data plane runs on a separate switching ASIC. Its four Gigabit Ethernet MACs support out-of-band management plus dual-stack uplinks to the fabric. Place the MPU on the management card with 512 MB DDR2, 32 MB NOR boot flash, and a TSI switch for serial I/O. The extended -40C to +105C temperature range ensures operation in hot telco closet environments, while the 783-FCBGA package enables compact management-card footprints behind the switching ASIC.
Recomendado
Network-Attached Storage (NAS) Controller
The MPC8548VJATGD powers mid-range NAS controllers where its dual DDR2 controllers handle large memory-mapped RAID cache, and its dual Gigabit Ethernet provides link aggregation for SMB/NFS throughput. The integrated USB 2.0 ports enable external backup targets without additional glue logic. Place the MPU between SATA multiplies (e.g. Sil3132) and the Ethernet PHY, with 1 GB DDR2 ECC for RAID5 write-back cache. The security engine accelerates encrypted-filesystem (eCryptfs/dm-crypt) operations, while the 783-FCBGA package's high pin density keeps the controller board within a 4x4 inch envelope.
Recomendado
Industrial Edge Controller / Soft PLC
The MPC8548VJATGD's industrial temperature grade (-40C to +105C) and dual Gigabit Ethernet suit it for industrial edge controllers and soft-PLC applications where deterministic networking and protocol conversion (Modbus TCP, EtherNet/IP, PROFINET) are required. The 1.2 GHz e500 core runs soft-PLC runtimes with cycle times under 1 ms for typical ladder logic. Place the MPU alongside isolated RS-485 transceivers and a managed Ethernet switch, with DDR2 for runtime buffering and NOR flash for firmware. The 783-FCBGA package with industrial-grade screening withstands factory-floor vibration profiles per IEC 60068.
Recomendado
Printer/MFP Controller Board
The MPC8548VJATGD serves as the main controller in office multi-function printers, where its USB 2.0 ports handle direct PC/Mac connectivity, Gigabit Ethernet provides network printing/scanning, and the e500 core runs the embedded RIP and scan pipeline. The DDR2 controller supports large page-buffer RAM for high-DPI rendering. Place the MPU on the engine controller board with DDR2, NAND flash for job storage, and a PCI Express link to the scanner CCD ASIC. The compact 783-FCBGA footprint keeps the controller board within the tight engine chassis envelope, while the integrated peripherals eliminate external bus-bridge chips.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MPC8548VJATGD — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MPC8548PXATGD | MPC8548VJAUQD | MPC8548ECVJATGD | MPC8548EVJATGD | MPC8548VJAQGD | MPC8548VJANGD |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 783-FCBGA (29x29 mm) | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same |
| Core Architecture | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 |
| Maximum Core Frequency | 1.2 GHz | 1.2 GHz | 1.2 GHz | 1.2 GHz | 1.2 GHz | 1.2 GHz | 1.2 GHz |
| Operating Temperature | -40C to +105C | Different temp grade (PX suffix) | -40C to +105C (AUQ screening) | -40C to +105C (engineering sample) | -40C to +105C (engineering sample) | -40C to +105C (AQ screening) | -40C to +105C (AN screening) |
| L2 Cache | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB |
| DDR2 Memory Controllers | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Gigabit Ethernet MACs | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) |
Diferenciadores clave
- Single-core 1.2 GHz e500 with integrated security engine for wireline routing (frente a MPC8560CVT667JC)
- Drop-in same-package alternatives for second-source flexibility (frente a MPC8548PXATGD)
- High-pin-count BGA with integrated multi-protocol SERDES (frente a P2040NSN1HLB)
Notas de diseño
Estimated: at 1.2 GHz core frequency the MPC8548VJATGD dissipates approximately 8 W typical core power. The 783-FCBGA package requires a minimum 4-layer PCB with a dedicated thermal pad array under the BGA tied to an inner ground plane with thermal vias (0.3 mm pitch, 0.5 oz copper fill). In fanless chassis, derate ambient to +70C maximum; in fan-cooled enclosures, ensure airflow of at least 1 m/s across the BGA top side. Without a proper thermal pad, junction temperature can exceed +125C and trigger thermal shutdown under sustained packet-processing load.
The DDR2 data, address, and clock signals require matched-length routing within 25 mil tolerance per byte lane and 50 mil across bytes to meet the 600 MHz data-rate specification. Use microstrip or stripline topology with reference to a continuous ground plane. Place VTT termination resistors at the midpoint of each address/control trace group. The RapidIO and PCI Express SERDES lanes require 100 ohm differential impedance and length matching within 5 mil. Place AC-coupling capacitors on the SERDES TX pairs as close to the MPU balls as possible per the NXP hardware specification.
Do not assume the boot ROM configuration is the same across all MPC8548 suffixes - VJ, PX, AUQ, AN, AQ designations differ in reset configuration word defaults and JTAG boundary-scan behavior. Verify the SYS_CONFIG pins and reset configuration word against the exact part marking before board bring-up. Additionally, the security engine requires firmware key loading via the secure boot flow; bypassing it leaves IPSec/SSL acceleration disabled. Always check NXP errata documents for revision-specific issues (e.g. DDR2 training lock, SERDES PLL lock time) before finalising firmware release.
Información de cumplimiento
RoHS/lead-free confirmed per Mouser product listing. REACH, halogen-free, and conflict-minerals declarations should be requested through NXP compliance portal or distributor (DigiKey/Mouser) compliance documents. AEC-Q100 not applicable - this is an industrial-grade communications MPU, not an automotive-qualified part.