MPC8548VJATGD - PowerQUICC III e500 MPU 1.2GHz 783-FCBGA | NXP
부품 번호: MPC8548VJATGD ✓ 활성MPC8548VJATGD 개요
An embedded microprocessor, also referred to as a microprocessor unit (MPU) or communications processor, integrates a CPU core, memory controllers, and peripheral interfaces on a single die. The MPC85xx family extends the PowerQUICC architecture (PowerQUICC -> communications SoC -> application-specific MPU) used in routers, base stations, and storage area network equipment. Compared with general-purpose microcontrollers, these MPUs emphasise high-throughput serial interfaces, deterministic interrupt latency, and hardware-accelerated communications blocks.
Key features include an e500 core with 36-bit physical addressing, 512 KB of L2 cache (configurable as SRAM), dual integrated DDR2 memory controllers supporting up to 600 MHz data rate, four Gigabit Ethernet MACs (two SGMII, two RGMII), two PCI Express interfaces, two RapidIO interfaces, two USB 2.0 controllers, and a security engine. The integrated DDR2 controller eliminates external memory bridge ICs and reduces BOM cost for high-throughput embedded systems.
Architecture depth: the e500 core implements Book-E architecture extensions, dual-issue superscalar pipeline, and hardware table-walk for virtualisation-aware systems. The 90 nm process node achieves the 1.2 GHz operating frequency while keeping typical core power within 8 W, suitable for fan-cooled chassis. The integrated security engine accelerates IPSec, SSL/TLS, SRTP, and 3GPP cipher suites, offloading packet processing from the core and improving aggregate system throughput.
Typical applications include multiservice routers, enterprise switches, line cards for wireless base stations, network-attached storage controllers, and industrial control modules. The high integration enables compact line-card designs with reduced component count, while the dual Ethernet and PCI Express lanes allow direct attachment of PHY devices and switch fabrics.
When designing with this MPU, ensure adequate thermal management - the 783-FCBGA package dissipates several watts under sustained load, and a minimum four-layer PCB with dedicated power and ground planes is required to meet signal-integrity targets for DDR2 and Gigabit Ethernet. Designers should also validate RapidIO or PCI Express SerDes reference clock jitter against the requirements in the NXP hardware specification.
This page consolidates distributor pricing, drop-in same-package alternatives, and practical design guidance beyond what the manufacturer datasheet provides, giving engineers a single resource for evaluation, sourcing, and second-source planning.
드롭인 대체품: MPC8548VJATGD — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
MPC8548PXATGD
✅ 드롭인가격 문의
데이터시트 보기 →MPC8548VJAUQD
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MPC8548ECVJATGD
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MPC8548EVJATGD
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MPC8548VJAQGD
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MPC8548VJANGD
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MPC8548VJATGD 최대 정격 & 전기적 특성
| Manufacturer | NXP Semiconductors |
| Series | MPC85xx / PowerQUICC III |
| Core Architecture | PowerPC e500 |
| Number of Cores | 1 |
| 데이터 버스 폭 | 32-bit |
| Maximum Core Frequency | 1.2 GHz |
| 패키지 | 783-FCBGA (29x29 mm) |
| 실장 유형 | Surface Mount |
| L2 Cache | 512 KB |
| Memory Controller | Dual DDR2 (up to 600 MHz) |
| Ethernet | 4x Gigabit (2x SGMII + 2x RGMII) |
| PCI Express | 2 lanes |
| RapidIO | 2 interfaces |
| USB | 2x USB 2.0 |
| 동작 공급 전압 | 1.8 V / 2.5 V / 3.3 V |
| Process Node | 90 nm |
| 동작 온도 | -40C to +105C |
| Lead Free / RoHS | Yes (Lead-free per Mouser listing) |
MPC8548VJATGD 783-fcbga (29x29 mm) 핀 구성 가이드
MPC8548VJATGD(783-fcbga (29x29 mm) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MPC8548VJATGD.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MPC8548VJATGD 적합 용도: 6 애플리케이션s: Multiservice Router / Branch Office Gateway, Wireless Base Station Line Card, Enterprise Network Switch Control Plane, Network-Attached Storage (NAS) Controller, Industrial Edge Controller / Soft PLC, Printer/MFP Controller Board.
Multiservice Router / Branch Office Gateway
The MPC8548VJATGD's 1.2 GHz e500 core plus dual DDR2 controllers and four Gigabit Ethernet MACs make it ideal for small-to-medium enterprise routers and VPN gateways. The integrated security engine accelerates IPSec, SSL/TLS, and 3GPP cipher suites, offloading crypto from the main CPU and pushing aggregate encrypted throughput above 1 Gbps for typical IPsec-AES128 traffic. Place the MPU between PHY transceivers (SGMII/RGMII) and the WAN modem module with 16-bit DDR2-800 ECC memory for buffer pools. The 783-FCBGA footprint enables fan-cooled fanless chassis designs with sufficient copper for the 1.2 GHz power envelope, while the four SERDES lanes support direct attachment of multi-port Ethernet PHYs without external switches.
추천
Wireless Base Station Line Card
The MPC8548VJATGD's PCI Express and RapidIO interfaces suit it for base-station line cards where it terminates Layer 2 traffic and feeds baseband DSPs via SRIO. Its deterministic interrupt latency and dual DDR2 controllers provide the bandwidth headroom required for LTE/HSPA+ MAC scheduling. Place the MPU alongside TI TMS320C66x DSPs via x1 PCIe, with four SERDES lanes and one RapidIO port for backhaul. The 783-FCBGA thermal envelope (operating up to +105C) supports outdoor base-station chassis without derating, while the security engine accelerates SRTP cipher suites for voice-data confidentiality.
추천
Enterprise Network Switch Control Plane
The MPC8548VJATGD serves as the control-plane CPU on managed Layer 2/3 enterprise switches, handling routing tables, ACL updates, SNMP, and CLI management while the data plane runs on a separate switching ASIC. Its four Gigabit Ethernet MACs support out-of-band management plus dual-stack uplinks to the fabric. Place the MPU on the management card with 512 MB DDR2, 32 MB NOR boot flash, and a TSI switch for serial I/O. The extended -40C to +105C temperature range ensures operation in hot telco closet environments, while the 783-FCBGA package enables compact management-card footprints behind the switching ASIC.
추천
Network-Attached Storage (NAS) Controller
The MPC8548VJATGD powers mid-range NAS controllers where its dual DDR2 controllers handle large memory-mapped RAID cache, and its dual Gigabit Ethernet provides link aggregation for SMB/NFS throughput. The integrated USB 2.0 ports enable external backup targets without additional glue logic. Place the MPU between SATA multiplies (e.g. Sil3132) and the Ethernet PHY, with 1 GB DDR2 ECC for RAID5 write-back cache. The security engine accelerates encrypted-filesystem (eCryptfs/dm-crypt) operations, while the 783-FCBGA package's high pin density keeps the controller board within a 4x4 inch envelope.
추천
Industrial Edge Controller / Soft PLC
The MPC8548VJATGD's industrial temperature grade (-40C to +105C) and dual Gigabit Ethernet suit it for industrial edge controllers and soft-PLC applications where deterministic networking and protocol conversion (Modbus TCP, EtherNet/IP, PROFINET) are required. The 1.2 GHz e500 core runs soft-PLC runtimes with cycle times under 1 ms for typical ladder logic. Place the MPU alongside isolated RS-485 transceivers and a managed Ethernet switch, with DDR2 for runtime buffering and NOR flash for firmware. The 783-FCBGA package with industrial-grade screening withstands factory-floor vibration profiles per IEC 60068.
추천
Printer/MFP Controller Board
The MPC8548VJATGD serves as the main controller in office multi-function printers, where its USB 2.0 ports handle direct PC/Mac connectivity, Gigabit Ethernet provides network printing/scanning, and the e500 core runs the embedded RIP and scan pipeline. The DDR2 controller supports large page-buffer RAM for high-DPI rendering. Place the MPU on the engine controller board with DDR2, NAND flash for job storage, and a PCI Express link to the scanner CCD ASIC. The compact 783-FCBGA footprint keeps the controller board within the tight engine chassis envelope, while the integrated peripherals eliminate external bus-bridge chips.
추천
추천 제품 요약
엔지니어링 참조 데이터: MPC8548VJATGD — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MPC8548PXATGD | MPC8548VJAUQD | MPC8548ECVJATGD | MPC8548EVJATGD | MPC8548VJAQGD | MPC8548VJANGD |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 783-FCBGA (29x29 mm) | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same |
| Core Architecture | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 |
| Maximum Core Frequency | 1.2 GHz | 1.2 GHz | 1.2 GHz | 1.2 GHz | 1.2 GHz | 1.2 GHz | 1.2 GHz |
| Operating Temperature | -40C to +105C | Different temp grade (PX suffix) | -40C to +105C (AUQ screening) | -40C to +105C (engineering sample) | -40C to +105C (engineering sample) | -40C to +105C (AQ screening) | -40C to +105C (AN screening) |
| L2 Cache | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB |
| DDR2 Memory Controllers | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Gigabit Ethernet MACs | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) | 4 (2x SGMII + 2x RGMII) |
주요 차별점
- Single-core 1.2 GHz e500 with integrated security engine for wireline routing (vs MPC8560CVT667JC)
- Drop-in same-package alternatives for second-source flexibility (vs MPC8548PXATGD)
- High-pin-count BGA with integrated multi-protocol SERDES (vs P2040NSN1HLB)
설계 노트
Estimated: at 1.2 GHz core frequency the MPC8548VJATGD dissipates approximately 8 W typical core power. The 783-FCBGA package requires a minimum 4-layer PCB with a dedicated thermal pad array under the BGA tied to an inner ground plane with thermal vias (0.3 mm pitch, 0.5 oz copper fill). In fanless chassis, derate ambient to +70C maximum; in fan-cooled enclosures, ensure airflow of at least 1 m/s across the BGA top side. Without a proper thermal pad, junction temperature can exceed +125C and trigger thermal shutdown under sustained packet-processing load.
The DDR2 data, address, and clock signals require matched-length routing within 25 mil tolerance per byte lane and 50 mil across bytes to meet the 600 MHz data-rate specification. Use microstrip or stripline topology with reference to a continuous ground plane. Place VTT termination resistors at the midpoint of each address/control trace group. The RapidIO and PCI Express SERDES lanes require 100 ohm differential impedance and length matching within 5 mil. Place AC-coupling capacitors on the SERDES TX pairs as close to the MPU balls as possible per the NXP hardware specification.
Do not assume the boot ROM configuration is the same across all MPC8548 suffixes - VJ, PX, AUQ, AN, AQ designations differ in reset configuration word defaults and JTAG boundary-scan behavior. Verify the SYS_CONFIG pins and reset configuration word against the exact part marking before board bring-up. Additionally, the security engine requires firmware key loading via the secure boot flow; bypassing it leaves IPSec/SSL acceleration disabled. Always check NXP errata documents for revision-specific issues (e.g. DDR2 training lock, SERDES PLL lock time) before finalising firmware release.
규정 준수 정보
RoHS/lead-free confirmed per Mouser product listing. REACH, halogen-free, and conflict-minerals declarations should be requested through NXP compliance portal or distributor (DigiKey/Mouser) compliance documents. AEC-Q100 not applicable - this is an industrial-grade communications MPU, not an automotive-qualified part.