OPA2682N - Dual Wideband Buffer Amplifier | Texas Instruments
N.º de pieza: OPA2682N ✓ ActivoOPA2682N Descripción general
A buffer amplifier is an analog amplifier stage that provides high input impedance and low output impedance. This impedance separation allows a source to drive a downstream circuit without significantly changing the source operating condition. The OPA2682N is identified as a wideband buffer amplifier with a fixed gain of 2, making it suitable for signal-chain stages, impedance conversion, cable-driver interfaces, instrumentation, and test-and-measurement systems where preserving signal amplitude and bandwidth is important.
The defining product characteristics include two amplifier circuits in one package and a 14-SOIC footprint. Because both channels are integrated into one device, the OPA2682N can implement dual-channel buffering with fewer external components and a smaller total board footprint than two separate single-channel buffer packages. A fixed gain of 2 also allows the stage to provide predictable signal-level gain while preserving the wideband operating intent of the device family.
The OPA2682N can be used in balanced or unbalanced analog signal paths, including instrumentation front ends, communications interfaces, data-conversion support circuits, and laboratory or industrial signal-conditioning equipment. Its dual-channel arrangement is particularly useful when two related signals must be buffered with matched device characteristics, such as differential signal chains, complementary outputs, or synchronous acquisition channels.
PCB implementation should follow the manufacturer pinout and land pattern for the 14-SOIC package. Keep input and output routing short, provide a stable low-impedance reference connection, and observe the decoupling and stability recommendations in the manufacturer datasheet. Because the available product listing identifies the device as a two-circuit 14-SOIC buffer amplifier but does not publish a complete electrical characterization, verify voltage, current, bandwidth, noise, slew rate, and thermal limits against the current manufacturer datasheet before release to production.
This product page combines the verified package and device classification with practical selection guidance, pinout-design considerations, lifecycle-oriented sourcing guidance, and a conservative comparison framework. It is intended to help engineers establish whether the OPA2682N fits the required channel count, package, gain, and analog signal-chain architecture before completing detailed circuit design.
Alternativas directas para OPA2682N — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasOPA2682N Valores máximos y características eléctricas
| Device Type | Dual fixed-gain wideband buffer amplifier |
| Number of Amplifier Circuits | 2 circuits |
| Number of Channels | 2 channels |
| Gain | 2 V/V |
| Encapsulado | 14-pin SOIC |
| Terminal Count | 14 terminals |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de OPA2682N 14-pin soic
Configuración de pines para OPA2682N (encapsulado 14-pin soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para OPA2682N.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
OPA2682N es adecuado para 6 aplicacións: Dual-Channel Instrumentation Buffering, Communication Signal-Chain Conditioning, Data-Acquisition Front Ends, Audio and Low-Frequency Signal Paths, Test and Measurement Buffering, Industrial Control and Sensor Interfaces.
Dual-Channel Instrumentation Buffering
The OPA2682N fits instrumentation designs requiring two buffered analog channels in one 14-pin SOIC package. Its two-circuit configuration is useful when a front end must isolate measurement sources from the impedance and capacitance of subsequent amplifier, ADC, or instrumentation modules. The fixed gain of 2 provides a defined signal-level increase while the buffer stage reduces loading sensitivity. Designers should verify input bias current, output-current capability, bandwidth versus load capacitance, and stability requirements against the manufacturer datasheet before committing the circuit.
Communication Signal-Chain Conditioning
OPA2682N can serve as a dual wideband buffer in communication equipment where transmit, receive, or auxiliary paths require impedance isolation. Combining two fixed-gain buffer circuits in a 14-pin SOIC reduces component count compared with two separate single-channel packages. The gain of 2 can restore signal level after passive losses, while the wideband classification supports higher-frequency analog paths. Validate channel bandwidth, output swing, capacitive-load stability, supply voltage, and maximum output current against the exact operating conditions before deployment.
Data-Acquisition Front Ends
The dual-channel OPA2682N is appropriate for front-end stages that feed sampling systems, particularly when two sensors or conditioned outputs must be buffered with matched device characteristics. High input impedance can limit source loading, while low output impedance helps drive the next analog stage. The fixed gain of 2 also provides a convenient level adjustment before conversion. Confirm input common-mode range, output swing, noise performance, settling behavior, and ADC interface requirements using the manufacturer datasheet and a circuit-level simulation.
Audio and Low-Frequency Signal Paths
OPA2682N can buffer two related low-frequency or wideband audio signals when the circuit requires stable impedance separation and a gain of 2. One channel may process a signal while the other handles a companion or complementary path, allowing the same device to provide consistent buffer behavior. Designers must confirm the device’s actual bandwidth, slew rate, output swing, noise, and load-drive capability in the manufacturer documentation. Use short, carefully routed traces and return the output to ground cleanly through the buffer’s own output impedance.
Test and Measurement Buffering
The OPA2682N is suitable for buffering sources in test and measurement equipment where the instrument must limit loading of the device under test. Two amplifier circuits allow a fixture or adapter to buffer two channels while keeping the assembly compact in a 14-pin SOIC package. The fixed gain of 2 can compensate for moderate path attenuation, but accuracy depends on the complete signal chain. Evaluate input capacitance, output drive, frequency response, and calibration requirements before selecting this device for precision measurement paths.
Industrial Control and Sensor Interfaces
OPA2682N can support industrial sensor interfaces that need buffered drive between a sensing element and downstream processing electronics. Its dual-circuit construction allows related sensor or control signals to share one package, while the buffer operation separates source and load impedances. Use it when the required bandwidth, common-mode range, and output drive are acceptable and when a gain of 2 matches the signal architecture. Industrial designs must also review temperature range, supply tolerances, transient protection, and isolation requirements before incorporating the amplifier.
Datos de referencia de ingeniería para OPA2682N — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Brand | Texas Instruments |
| Package | 14-pin SOIC |
| Device Type | Wideband buffer amplifier |
| Amplifier Circuits | 2 circuits |
| Channels | 2 channels |
| Gain | 2 V/V |
| Mounting Type | Surface mount |
Diferenciadores clave
- Two integrated buffer channels in one package (frente a OPA2682N/2K5)
- Wideband fixed-gain buffer function (frente a General-purpose single-channel operational amplifier)
- Compact dual-channel implementation (frente a Two separate single-channel buffer packages)
Notas de diseño
Assign the OPA2682N nets from the manufacturer pin-description table and use the land pattern specified for the 14-pin SOIC. Keep each input route short and connect the bypass capacitor directly between the relevant supply and ground pins. Maintain a low-impedance ground return beneath and around the device, and avoid routing high-current or fast-switching paths beneath the analog inputs to reduce ground bounce and unwanted coupling.
Do not treat a 14-pin SOIC footprint alone as proof that another buffer amplifier is interchangeable. A replacement must match the two-channel architecture, gain of 2, supply limits, bandwidth, output-drive capability, stability with the intended load, and every signal connection. Review the complete ordering suffix as well, since OPA2682N/2K5 is a commercial variant of the same device family and may have different packing or order-processing details.
Validate capacitive loading at each buffered output and preserve the manufacturer’s recommended operating and compensation conditions. Long PCB traces, probe capacitance, and long cable connections can change the effective load seen by the output stage and may affect frequency response or stability. If the output must drive a cable or large capacitive node, perform an end-to-end step-response test and evaluate series isolation resistance before production release.
Información de cumplimiento
No specific compliance declaration was identified in the product listings. Review the current Texas Instruments product page, material declaration, and quality documentation for the selected ordering suffix before procurement.