PCM1773RGA - 24-Bit Stereo Audio DAC | Texas Instruments
N.º de pieza: PCM1773RGA ✓ ActivoPCM1773RGA Descripción general
A stereo audio DAC converts digital PCM samples into left- and right-channel analog voltages. The PCM1773RGA integrates that conversion function with line-out circuitry, reducing the number of external components required in typical audio signal paths. An I2S-compatible digital interface connects the converter to an audio processor, decoder, or digital audio source, while the integrated line-output stage provides an analog output suitable for subsequent voltage amplification or line-level routing.
The principal performance characteristics are 24-bit conversion resolution, 50 kHz maximum sampling performance, 98 dB SNR, and support for two audio channels. The manufacturer identifies the device as a low-voltage, low-power stereo DAC with hardware line-output control. Those characteristics place it between basic digital audio interfaces and higher-performance integrated audio converter families, where channel count, converter resolution, output topology, and control requirements determine the appropriate replacement path.
The PCM1773 family uses CMOS integrated circuitry containing stereo digital-to-analog converters, line-out circuitry, and support functions. In this configuration, the digital interface receives serial audio data while the converter reconstructs the analog waveform. The integrated line-output amplifier provides a more direct connection to the next analog stage than a bare converter output, although the exact output configuration, load capability, and gain settings must be confirmed against the manufacturer datasheet before finalizing a board design.
Typical uses include compact stereo audio playback, digital receiver and decoder designs, audio-interface modules, multimedia systems, and line-level analog output stages. The 24-bit interface is suitable for preserving source word depth, while the 98 dB SNR specification provides a clear dynamic-range figure for architecture selection. The 50 kHz sampling limit should be checked against the required source rate; designs operating at higher rates need a different converter family.
PCB planning should place the digital interface, analog outputs, bypass capacitors, and exposed thermal pad according to the manufacturer layout guidance. Maintain the required supply voltage, grounding, and output-load conditions, and account for the exposed pad when defining copper area and thermal relief. Do not assume that a same-package family member is interchangeable without verifying pin functions, control polarity, output configuration, and timing requirements.
This product page consolidates the known 24-bit, two-channel, 50 kHz, 98 dB SNR, I2S, line-out, and VQFN-20 characteristics with practical integration guidance. It also distinguishes documented device facts from engineering details that still require confirmation from the manufacturer datasheet, helping designers move from part selection to a controlled schematic and layout review.
Alternativas directas para PCM1773RGA — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PCM1773RGA (mismo factor de forma y huella) — difiere en Package, Number of DAC Channels, Operating Temperature Range, Output Stage, Product Type.
PCM1773RGAR
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
PCM1773RGA.B
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PCM1772RGA
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →PCM1771RGA
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PCM1770RGAR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PCM1773RGA Valores máximos y características eléctricas
| Product Type | Stereo audio digital-to-analog converter with line-out amplifier |
| Manufacturer | Texas Instruments |
| Number of DAC Channels | 2 channels |
| Converter Resolution | 24 bit |
| Maximum Sampling Rate | 50 kHz |
| Signal-to-Noise Ratio | 98 dB |
| Digital Audio Interface | I2S |
| DAC Architecture | Delta-sigma |
| Output Stage | Integrated stereo line-out amplifier |
| Output Control | Hardware control |
| Rango de temperatura de funcionamiento | 0 °C to +70 °C |
| Encapsulado | 20-pin VQFN (RGA), 4.2 mm × 4.2 mm |
| Tipo de montaje | Surface mount |
| Process Technology | CMOS |
Guía de configuración de pines de PCM1773RGA 20-pin vqfn (rga), 4.2 mm × 4.2 mm
Configuración de pines para PCM1773RGA (encapsulado 20-pin vqfn (rga), 4.2 mm × 4.2 mm). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para PCM1773RGA.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
PCM1773RGA es adecuado para 6 aplicacións: Compact Digital Audio Playback, Multimedia Audio Module, Digital Audio Receiver, Line-Level Audio Interface, Portable Audio Equipment, Audio Development Platform.
Compact Digital Audio Playback
PCM1773RGA fits compact playback systems that need to convert two-channel I2S audio into analog line-level signals. Its 24-bit conversion resolution preserves the source word depth, while the 50 kHz sampling limit must remain compatible with the encoded program material. The 98 dB SNR specification provides a defined dynamic-range target for consumer and professional playback equipment. Placing the integrated line-out stage close to the analog routing section reduces external circuitry and keeps the converter and analog output path within a compact 4.2 mm × 4.2 mm VQFN footprint.
Recomendado
Multimedia Audio Module
The PCM1773RGA can provide the stereo analog output stage for a multimedia module driven by a digital audio processor. Two-channel 24-bit I2S data suits the converter's interface, and the 50 kHz maximum sampling rate covers applications that do not require higher-rate audio. With a 98 dB SNR rating and integrated line-out amplifier, it supports a practical transition from digital processing to an external voltage amplifier. Board design should separate digital routing from the analog output path and follow the manufacturer guidance for bypass capacitance and grounding.
Recomendado
Digital Audio Receiver
In a digital receiver, PCM1773RGA can convert a recovered two-channel I2S stream into analog audio suitable for line-level routing. The 24-bit interface accommodates high-resolution source data when the upstream decoder supports it, while the 98 dB SNR figure helps preserve quiet-source detail. The converter's integrated line-out circuitry can simplify the analog path compared with a bare DAC implementation. System designers should verify source clocking, sample-rate compatibility, output loading, and the required analog gain before finalizing the receiver architecture.
Recomendado
Line-Level Audio Interface
PCM1773RGA is suitable for a small line-level interface that accepts digital stereo audio and exposes analog outputs to downstream processing equipment. The two-channel 24-bit architecture supports conventional stereo routing, and the 50 kHz rate covers many communication and consumer audio streams. A 98 dB SNR specification provides a useful baseline for a converter intended to preserve low-level program material. The board must meet the converter's grounding, supply, output-load, and filtering requirements while keeping sensitive analog traces away from digital clock and data paths.
Recomendado
Portable Audio Equipment
The low-voltage, low-power positioning of PCM1773RGA makes it a candidate for portable audio products that convert a digital playback source into an analog line signal. Its compact 20-pin VQFN package leaves board area for the amplifier, storage, controls, and battery management. The converter supports 24-bit data in a two-channel I2S configuration and provides 98 dB SNR. Designers should confirm the exact supply range and power consumption, then budget thermal and power-management capacity for the complete analog output stage.
Recomendado
Audio Development Platform
PCM1773RGA can serve as the audio-output element of an evaluation platform designed to compare digital filtering, clocking, and analog-output behavior. Its two-channel 24-bit I2S interface provides a straightforward connection to common audio processors, while the integrated line-out amplifier creates a useful test point for downstream amplifier development. The 98 dB SNR specification gives developers a measurable baseline, and the 4.2 mm × 4.2 mm package simplifies comparison with other converter options. Firmware and board bring-up should use the manufacturer timing and application guidance.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PCM1773RGA — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Brand | Texas Instruments |
| Package | 20-pin VQFN (RGA), 4.2 mm × 4.2 mm |
| Product Type | Stereo audio DAC with integrated line-out amplifier |
| DAC Channels | 2 channels |
| Converter Resolution | 24 bit |
| Maximum Sampling Rate | 50 kHz |
| Signal-to-Noise Ratio | 98 dB |
| Digital Audio Interface | I2S |
| Output Control | Hardware control |
| Operating Temperature Range | 0 °C to +70 °C |
Diferenciadores clave
- Integrated stereo line-out stage (frente a PCM1770RGAR)
- Defined 24-bit, 50 kHz conversion performance (frente a PCM1771RGA)
- Compact integrated converter footprint (frente a PCM1773RGAR)
Notas de diseño
Route the I2S clock, data, and control signals away from the stereo analog outputs and the line-output return paths. Place the device-side bypass capacitors at the pins specified by the manufacturer application circuit, and use a compact, low-impedance ground return for the analog section. Review every supply connection and exposed-pad connection against the manufacturer layout drawing before fabrication.
Verify the converter supply voltage, output amplitude, and load limits before defining the power tree. The low-voltage, low-power description does not specify the permitted operating range or current consumption. Use the manufacturer electrical-characteristics table for quiescent current and operating conditions, and size the regulator for the converter plus the connected analog load rather than for the DAC alone.
Do not assume that PCM1770RGAR, PCM1771RGA, PCM1773RGAR, or another same-family part is a drop-in replacement. A valid board-level substitution requires matching pin functions, I2S timing, control polarity, output configuration, supply limits, and exposed-pad requirements. Packaging suffixes also need separate ordering review because reel or tube format is an orderable attribute, not a change in electrical functionality.
Keep digital clock routing short and controlled because the I2S clock establishes the timing reference for both channels. Use a ground-plane strategy that avoids splitting the analog return beneath the converter or line-output circuitry. Confirm output filtering and capacitive-load restrictions from the manufacturer datasheet, and test both channels for startup transients and channel-to-channel alignment at the intended sample rate.
Información de cumplimiento
Compliance status is not stated in the manufacturer product information used for this page. The standard commercial PCM1773RGA ordering configuration is not identified as AEC-Q100 qualified by the available information.