محصولات (46,000+)

INA132U/2K5 - 2.5 Gain Differential Amplifier | Texas Instruments
INA132U/2K5

INA132U/2K5 - 2.5 Gain Differential Amplifier | Texas Instruments

The Texas Instruments INA132U/2K5 is a low-power, single-supply differential amplifier with a fixed gain of 2.5, a 2.7 V to 36 V operating range, and an 8-pin SOIC package. The device combines a precision operational amplifier with an integrated, laser-trimmed resistor network to measure small voltage differences accurately while rejecting large common-mode signals. A difference amplifier is an analog signal-conditioning circuit that subtracts one input voltage from another and amplifies the result. The INA132U/2K5 belongs to the instrumentation-amplifier and precision-differential-amplifier hierarchy, where accurate gain and common-mode rejection are essential for converting small sensor outputs into signals suitable for analog-to-digital converters, control systems, and measurement equipment. The integrated resistor network gives the /2K5 ordering option a fixed gain of 2.5, while laser trimming supports accurate gain and high common-mode rejection. The amplifier operates from a single 2.7 V to 36 V supply and can also be used with split supplies where the input and output voltages remain within the device's electrical limits. Its low-power design makes it suitable for battery-powered and industrial instrumentation systems. The INA132U/2K5 accepts input signals through differential IN+ and IN− terminals and provides the amplified difference at OUT. A reference terminal permits the output to be shifted relative to a chosen voltage when the application cannot use a ground-centered signal. The internal architecture simplifies PCB design by reducing the number of external precision resistors normally required for a discrete difference amplifier. Typical uses include bridge-transducer excitation and readout, precision current sensing, industrial process monitoring, battery-powered sensing, and low-level differential signal acquisition. Because the device has a fixed 2.5 gain, engineers should verify that the required signal gain, common-mode range, output swing, and supply voltage match before placing it in a new design. Layout quality directly affects differential-signal performance. Route the IN+ and IN− paths as a closely matched pair, keep the reference and output nodes away from switching-current paths, and use a low-noise supply arrangement with local bypass capacitors. Confirm input and output common-mode limits at the operating temperature and check the final gain tolerance against the system measurement budget. This page combines ordering information, technical limits, drop-in replacement analysis, comparison data, and application-specific design guidance. It is intended to help engineers identify whether the INA132U/2K5 provides the required gain, supply range, package, and replacement compatibility before committing a board layout.

RFQ تماس
INA132UA - Low-Power Difference Amplifier | Texas Instruments
INA132UA

INA132UA - Low-Power Difference Amplifier | Texas Instruments

The Texas Instruments INA132UA is a low-power, unity-gain difference amplifier with a 500 uV input-referred offset, 300 kHz gain-bandwidth product, and low 160 uA quiescent current. Designed for precision differential measurement, the device combines a precision operational amplifier with a laser-trimmed internal resistor network. It is offered in an 8-pin SOIC package and supports single-supply operation up to 36 V or dual-supply operation up to ±18 V. A difference amplifier is a specialized operational-amplifier circuit that measures the voltage difference between two input nodes while rejecting voltage common to both inputs. Within the amplifier-IC hierarchy, the INA132UA belongs to the precision instrumentation-amplifier family, combining an operational amplifier, precision gain-setting resistors, and high common-mode rejection in one package. This integration reduces external component count while preserving accurate gain behavior across temperature. The principal features of the INA132UA include 90 dB common-mode rejection, ±0.075% maximum gain error, and 0.001% maximum nonlinearity. Its internal resistors are laser trimmed for accurate gain, and their temperature-coefficient tracking helps preserve gain accuracy and common-mode rejection over operating temperature. The low-power architecture operates from a single supply as high as 36 V, making it suitable for both compact battery-powered systems and higher-voltage industrial instrumentation. The INA132UA uses a unity-gain architecture, so the differential output is scaled 1:1 from the difference between its inputs. The internal precision resistor network establishes the gain relationship without an external gain-setting resistor. Its common-mode rejection is particularly important when a small sensor signal is superimposed on a larger reference or supply-derived voltage, because the amplifier attenuates the common component while retaining the differential measurement. Typical applications include bridge-sensor and transducer signal conditioning, current-shunt measurement, battery and power-system monitoring, industrial process-control instrumentation, and precision analog sensing. The device is also appropriate for low-side current sensing when the input common-mode voltage remains within the operating range. Its 8-pin SOIC footprint supports conventional surface-mount assembly. Designers should preserve the input common-mode and output-voltage limits, provide stable input and output bypassing, and verify that source impedances remain compatible with the amplifier's input and common-mode performance. The low quiescent current reduces supply demand, but input bias current and common-mode behavior still determine accuracy in high-impedance sensor circuits. The manufacturer pin-description table should be used when assigning PCB tracks and confirming polarity. This product record combines the device's manufacturer-defined characteristics with same-package replacement guidance, application-specific engineering context, and practical layout considerations. It is intended to help engineers identify whether the unity-gain INA132UA fits a differential-measurement design without confusing it with wider-gain or different-supply-range amplifier families.

RFQ تماس
INA133U - 1.5MHz Precision Difference Amplifier | TI
INA133U

INA133U - 1.5MHz Precision Difference Amplifier | TI

The Texas Instruments INA133U is a 1.5 MHz, precision unity-gain difference amplifier with up to 450 µV offset, 0.95 mA typical power-supply current, and an 8-pin SOIC package. Designed for low-level differential measurement, it combines a precision operational amplifier with a laser-trimmed resistor network for accurate gain and common-mode rejection. The device is offered in the INA133U package configuration identified by DigiKey as an 8-SOIC differential amplifier. A difference amplifier is a specialized analog amplifier that amplifies the voltage difference between two inputs while rejecting signals common to both inputs. This function is useful when a sensor, transducer, or measurement node is exposed to large common-mode voltages and the desired information exists only as a small differential signal. In the broader hierarchy, the INA133U belongs to instrumentation and difference amplifiers, within operational amplifiers and analog signal-conditioning ICs. The INA133U combines 1.5 MHz bandwidth with low offset voltage and low power consumption. Its high-speed behavior makes it suitable for current-shunt monitoring, bridge excitation, differential sensing, and industrial signal-conditioning systems. The on-chip laser-trimmed resistors are designed to improve gain accuracy and common-mode rejection, while their temperature-coefficient tracking helps preserve performance across temperature changes. The precision architecture is important because it combines amplifier bandwidth with accurate differential gain. A difference amplifier can reject shared interference, but its usefulness still depends on common-mode voltage staying within the device operating limits and on the surrounding circuit presenting suitable impedance and filtering. Designers should verify the complete input, output, supply, and common-mode conditions from the manufacturer datasheet. Typical applications include high-side current measurement, differential voltage sensing, bridge-based sensor interfaces, amplifier-input protection networks, and industrial control systems. In a shunt monitor, the INA133U can amplify the voltage across a low-ohm resistor while reducing the effect of supply or ground disturbances. In bridge sensing, it helps convert a small differential sensor output while rejecting common-mode excitation voltage. The principal design trade-off is bandwidth versus precision and power. The 1.5 MHz bandwidth supports faster signal changes than a purely low-bandwidth precision amplifier, while the 0.95 mA power figure favors low-power systems. PCB layout should keep input traces short, use a solid ground reference, and provide stable supply bypassing. This page synthesizes the verified manufacturer and distributor information, practical design considerations, and carefully limited replacement guidance.

RFQ تماس
INA133UA - 1.5 MHz Precision Difference Amplifier | Texas Instruments
INA133UA

INA133UA - 1.5 MHz Precision Difference Amplifier | Texas Instruments

Texas Instruments INA133UA is a precision difference amplifier with 1.5 MHz bandwidth, 450 uV maximum offset voltage, and 0.95 mA power consumption. The device is packaged in an 8-pin SOIC surface-mount package and is designed for high-speed signal-chain applications where a differential input must be amplified accurately. According to the Texas Instruments INA133 product information, the INA133 family uses a unity-gain configuration and provides high gain accuracy and common-mode rejection ratio. The verified product listing identifies the INA133UA as a differential amplifier in an 8-SOIC package, while the INA133UA/2K5 ordering variant is also listed in an 8-pin SOIC package. A difference amplifier is an operational-amplifier-based circuit that responds to the voltage difference between two input terminals rather than to either input voltage independently. This makes the INA133UA suitable for current-sense, bridge-sensor, instrumentation, and high-speed measurement circuits where common-mode voltage can be substantially larger than the wanted differential signal. The 1.5 MHz bandwidth provides a useful compromise between response speed and precision, while the specified 450 uV offset and 0.05% maximum gain error help establish the accuracy of the amplified result. The INA133UA operates with single or dual power supplies according to the manufacturer family information. Its 0.95 mA power consumption is suitable for compact, low-power signal-conditioning equipment when compared with general-purpose implementations that consume more current. The 8-pin SOIC package permits conventional surface-mount assembly and provides a straightforward footprint for designs that require one precision differential amplifier. Typical uses include bridge-based pressure and load sensing, current measurement in power-conversion systems, industrial instrumentation, and high-speed analog signal conditioning. In each case, the input common-mode range, supply voltage, output swing, gain-setting method, and required common-mode rejection must be checked against the complete manufacturer datasheet before implementation. Designers should pay particular attention to input filtering, resistor matching, supply bypassing, and the output reference connection. The INA133UA is not automatically interchangeable with every 8-pin amplifier because package compatibility alone does not guarantee electrical compatibility. Verify the exact pinout, supply ratings, common-mode limits, gain configuration, and stability requirements before releasing a PCB. This product page combines the verified Texas Instruments product description, distributor package information, price reference, and cross-reference results with practical selection guidance for engineers evaluating a drop-in replacement.

RFQ تماس
INA133UA/2K5 - 1.5MHz Difference Amplifier | Texas Instruments
INA133UA/2K5

INA133UA/2K5 - 1.5MHz Difference Amplifier | Texas Instruments

The Texas Instruments INA133UA/2K5 is a precision differential amplifier with a 1.5 MHz bandwidth, 450 µV input offset voltage, and 0.95 mA power consumption, housed in an 8-pin SOIC package. Its integrated precision resistor network supports accurate differential measurement while maintaining common-mode rejection and gain stability over temperature. A difference amplifier is a specialized amplifier IC that subtracts two input voltages and amplifies the resulting differential signal. This category belongs to the wider amplifier hierarchy and is used to reject common-mode noise, monitor differential sensor outputs, and measure small voltage changes across high-potential or low-noise systems. The INA133 combines an internal amplifier with a trimmed resistor network to simplify high-accuracy gain configurations. Principal features include a 1.5 MHz gain-bandwidth product, 450 µV offset specification, and very low 0.95 mA power draw. The /2K5 ordering option identifies the specified differential amplifier configuration, while the UA package designation provides an 8-pin SOIC implementation. These characteristics make the device useful where signal speed and low power must coexist with precision differential input handling. The INA133 architecture uses laser-trimmed on-chip resistors with low temperature-coefficient tracking. This construction supports accurate gain and common-mode rejection across operating-temperature changes while eliminating the need for a discrete four-resistor subtraction network. Its bandwidth allows the amplifier to process signals beyond static bridge or sensor measurements, although practical usable frequency and accuracy also depend on source impedance, layout, and the required closed-loop response. Typical applications include current-shunt monitoring, bridge-sensor signal conditioning, precision differential measurement, industrial instrumentation, and low-power sensor interfaces. The amplifier can also serve as the input stage for filtering, control, or conversion circuitry when its bandwidth, offset, supply range, and common-mode performance suit the signal chain. When laying out the circuit, keep the differential input traces short, symmetric, and away from switching nodes. Resistor networks used to set input and output limits should be placed close to their associated pins, and bypass capacitance should follow the manufacturer’s recommended application circuit. Check input and output swing, common-mode range, and supply limits before adding gain. This product page consolidates the manufacturer’s principal INA133 specifications with engineering guidance for differential measurement. It also organizes same-package alternatives, design considerations, application fit, and parameter comparisons so engineers can evaluate the INA133UA/2K5 against other precision amplifier implementations before laying out a board.

RFQ تماس
INA133UG4 - 1.5MHz Precision Differential Amplifier | Texas Instruments
INA133UG4

INA133UG4 - 1.5MHz Precision Differential Amplifier | Texas Instruments

The Texas Instruments INA133UG4 is a single-circuit precision difference amplifier with a 1.5 MHz -3 dB bandwidth, 450 µV input offset voltage, 950 µA quiescent current, and an 8-SOIC package. Designed for instrumentation applications, it converts a differential input into a single-ended output while providing high common-mode rejection for signals embedded in larger voltage ranges. A precision difference amplifier is an amplifier subtype that subtracts two input voltages and amplifies the resulting differential signal. This measurement-focused category belongs to the hierarchy of instrumentation amplifiers, differential amplifiers, analog amplifiers, and semiconductor signal-conditioning ICs. Unlike a general-purpose operational amplifier configured with external resistors, the INA133 integrates matched internal resistors, reducing component count and improving resistance matching for bridge, shunt, and current-sense measurements. The INA133UG4 operates from 4.5 V to 36 V and supports output swings of approximately ±2.25 V to ±18 V, depending on supply voltage. Its 5 V/µs slew rate supports accurate reproduction of rapidly changing signals, while low power consumption of 0.95 mA suits battery-powered and portable instrumentation. The manufacturer identifies the device as a precision, low-power, high-performance difference amplifier. Internally, the INA133 combines four precision resistors with an operational-amplifier core to establish a fixed differential gain of 1. This architecture is useful when the desired output equals the difference between two input voltages, particularly for current measurement across a low-value shunt. Because it is a fixed-gain device, it avoids the gain-setting resistor network and feedback balance adjustments normally required by discrete difference-amplifier implementations. Typical uses include industrial current sensing, bridge-transducer excitation and readout, battery monitoring, laboratory measurement systems, and instrumentation interfaces that must reject large common-mode voltage. The wide 36 V maximum supply voltage also permits operation from protected industrial rails, although the selected output range must remain within the power-supply limits. The primary design consideration is common-mode range. Neither input should exceed the supply rails by more than the device permits, and the output must remain within its allowable swing. PCB layout should minimize differential-loop area, use a solid ground reference, and keep input and output return paths separated to reduce errors caused by parasitic resistance or ground gradients. This page combines manufacturer specifications, package information, application guidance, comparison parameters, and practical design notes to support faster component selection and implementation of the INA133UG4 in precision analog signal chains.

RFQ تماس
INA134PA - 0dB Audio Differential Receiver | Texas Instruments
INA134PA

INA134PA - 0dB Audio Differential Receiver | Texas Instruments

The Texas Instruments INA134PA is a single 0dB audio differential line receiver with a fixed gain of 1V/V, low distortion of 0.0005% at 1kHz, and a high slew rate of 14V/µs. The device is packaged in an 8-pin PDIP package and operates across a wide ±18V supply range with a maximum quiescent current of 2.9mA. An audio differential line receiver is a specialized amplifier that accepts a balanced or unbalanced audio signal, rejects common-mode noise, and produces a single-ended output. The INA134 belongs to the broader amplifier IC hierarchy and is intended for professional and high-fidelity audio paths where low distortion, adequate slew rate, common-mode rejection, and output drive are more important than a small package or minimal power consumption. Key features include a 90dB common-mode rejection ratio, fixed unity gain, 0.0005% distortion at 1kHz, and a 14V/µs slew rate. The wide output-voltage swing and high output-drive capability allow the receiver to drive downstream circuitry without adding substantial distortion. A maximum quiescent current of 2.9mA also supports straightforward analog power-supply design where adequate headroom and grounding remain important. Internally, the INA134 combines high-performance operational amplifiers with on-chip precision resistors. The integrated resistor network establishes the fixed 1V/V gain and helps control gain-related errors without requiring an external matched resistor set. Its differential architecture is intended to suppress signal-correlated noise and interference that appears equally on both input lines. Typical uses include balanced professional audio inputs, stereo differential line receivers, mixer input stages, audio interface front ends, and instrumentation that receives low-level differential signals. The INA134PA is particularly appropriate when an through-hole package is preferred and a ±15V or ±18V analog supply is available. The primary design consideration is ensuring adequate supply headroom for signal peaks and output swing. Input and return paths should be routed as a balanced pair, with attention to grounding and source impedance. Decoupling close to the supply pins and short, symmetric signal traces help preserve the receiver’s low-noise and high-rejection performance. This page combines verified manufacturer specifications, distributor availability information, lifecycle guidance, and an engineering-oriented comparison of the INA134PA with relevant alternatives. It also identifies where verified drop-in data is limited so engineers can distinguish confirmed compatibility from generic or cross-package substitutions.

RFQ تماس
INA134UA - Unity-Gain Audio Receiver | Texas Instruments
INA134UA

INA134UA - Unity-Gain Audio Receiver | Texas Instruments

The Texas Instruments INA134UA is a unity-gain differential audio line receiver with 0.0005% distortion at 1 kHz, a 14 V/µs slew rate, and 90 dB CMRR, housed in an 8-pin SOIC package. It uses on-chip precision resistors and high-performance operational amplifiers to convert balanced differential audio signals into a single-ended output. A differential line receiver is a special-purpose amplifier that rejects common-mode voltage and interference while amplifying the voltage difference between two signal inputs. In the amplifier hierarchy, the INA134UA is a differential receiver, then an audio amplifier, then an analog signal-conditioning IC. It is commonly used where a balanced source must feed an unbalanced input without introducing excessive noise, distortion, or ground-related errors. Key features include a fixed gain of 1 V/V, low distortion of 0.0005% at 1 kHz, a high slew rate of 14 V/µs, high CMRR of 90 dB, and maximum quiescent current of 2.9 mA. The wide supply range supports single-ended operation from 4 V to 18 V or dual supplies up to ±18 V. The manufacturer specifically identifies the device for high-performance audio applications. Technically, the INA134UA combines high-performance operational amplifiers with precision on-chip resistors in a fixed unity-gain configuration. Its differential input arrangement suppresses signal common to both inputs, while the fast slew rate supports dynamic audio waveforms. Wide output-voltage swing and strong output drive make the receiver useful between professional audio sources and downstream single-ended stages, although the exact output-drive and settling values must be confirmed in the manufacturer datasheet. Typical uses include professional audio consoles, balanced line inputs, mixer stages, studio preamplifier interfaces, broadcast equipment, and audio adapter boards. In these systems, the receiver can preserve a balanced source over a cable run and provide a clean single-ended signal for mixing or monitoring. The same features also suit instrumentation interfaces where cable pickup and ground-offset rejection are important. When designing around the INA134UA, verify input and output common-mode limits for the selected supply arrangement and confirm that downstream circuitry accepts a single-ended output. Keep input and output return paths short, use a stable reference ground for the source and receiver, and avoid placing high-current digital return paths beneath the audio input region. The 8-pin SOIC footprint also requires an appropriate thermal assessment if the output stage operates near its voltage limits. This product page consolidates verified manufacturer and distributor information, identifies genuine drop-in alternatives, and adds practical selection, layout, and signal-integrity guidance for engineers evaluating the INA134UA in audio and instrumentation systems.

RFQ تماس
INA134UA/2K5 - 0 dB Audio Receiver | Texas Instruments
INA134UA/2K5

INA134UA/2K5 - 0 dB Audio Receiver | Texas Instruments

Texas Instruments INA134UA/2K5 is a single-channel, unity-gain audio differential line receiver with a gain of 0 dB, a 14 V/us slew rate, and 0.0005% distortion at 1 kHz, housed in an 8-pin SOIC package. It accepts dual power supplies from ±4 V to ±18 V and operates across a -40°C to +85°C temperature range. An audio differential line receiver is a specialized analog amplifier that converts a small differential signal appearing across two conductors into a single-ended output. The INA134 belongs to the operational-amplifier hierarchy and the broader signal-conditioning category. Its internal precision resistors establish the unity differential gain, while its differential input arrangement rejects common-mode noise that appears equally on both input lines. The manufacturer specifies low distortion of 0.0005% at 1 kHz and a high slew rate of 14 V/us. These characteristics support accurate reproduction of high-amplitude and rapidly changing audio waveforms. The receiver also provides wide output voltage swing and high output-drive capability for driving downstream audio stages. Typical dual supplies include ±5 V, ±9 V, ±12 V, and ±15 V. Technically, the INA134 combines high-performance operational amplifiers with on-chip precision resistors. Its differential architecture is intended to suppress signal corruption from shared ground impedance and cable-induced common-mode voltage. A unity gain of 0 dB means the receiver primarily provides buffering and differential-to-single-ended conversion rather than voltage amplification. Typical uses include balanced audio input receivers, active mixer interfaces, professional audio equipment, consumer audio signal paths, and instrumentation requiring low-distortion differential input handling. The device is especially relevant when a balanced source must feed a conventional single-ended audio circuit while preserving signal integrity. Designers should observe the specified dual-supply limits, maintain common-mode input voltage within the operating region, and use appropriate bypassing close to the supply pins. Input and output routing should minimize loop area and preserve signal pairing. The 8-pin SOIC footprint also requires adequate thermal copper and assembly clearance where the operating environment is elevated.

RFQ تماس
INA137PA - ±6dB Audio Differential Receiver | Texas Instruments
INA137PA

INA137PA - ±6dB Audio Differential Receiver | Texas Instruments

Texas Instruments INA137PA is a single-channel audio differential line receiver based on a high-performance operational amplifier and on-chip precision resistors. It supports fixed gains of 1/2 (-6 dB) and 2 (+6 dB), operates from dual ±18 V supplies, and is packaged in an 8-pin PDIP. The receiver is intended for balanced audio inputs, professional audio equipment, consumer audio systems, and other applications that require rejection of common-mode signals while preserving low distortion. An audio differential line receiver is a specialized analog amplifier that amplifies the voltage difference between two input terminals while suppressing a voltage common to both inputs. This function belongs to the hierarchy of difference amplifier, instrumentation amplifier, operational amplifier, and signal-conditioning IC. Balanced audio transmission reduces sensitivity to ground-potential differences and conducted interference, making a precision differential receiver an important interface between a source and downstream audio circuitry. The INA137PA provides low distortion of 0.0005% at 1 kHz, a high slew rate of 14 V/µs, and common-mode rejection of 90 dB. Its quiescent current is specified at no more than 2.9 mA. The operational-amplifier architecture and integrated precision resistors simplify the implementation of a balanced receiver while retaining the wide output swing and strong output-drive characteristics described for the INA137 family. The input and feedback resistors can be reversed to select either -6 dB or +6 dB gain, according to the manufacturer datasheet. This flexibility allows a designer to attenuate a high-level balanced source or amplify a lower-level source without changing the receiver package. A unity-gain implementation is not provided by the INA137 itself; the manufacturer identifies INA134 and INA2134 for applications requiring 0 dB gain. Typical uses include receiving balanced professional-audio mixer outputs, converting balanced sources to unbalanced downstream inputs, conditioning stereo channel signals in broadcast equipment, and rejecting ground-offset noise in installation audio. Exact bandwidth, input impedance, output impedance, and temperature limits must be confirmed from the manufacturer documentation for the final operating conditions. When laying out the circuit, keep the differential input traces short, matched, and away from switching nodes. Place input and output bypassing capacitors close to their associated supply and signal pins, and route output signals away from high-current switching paths. Verify output swing, load capability, and thermal conditions before driving the next stage. This page organizes the documented INA137PA characteristics into an engineer-oriented selection guide, application guidance, verified pin-compatible alternatives, and practical layout notes. It also distinguishes the fixed -6 dB and +6 dB configurations from unity-gain receiver choices, helping prevent a package-compatible substitution from introducing an unintended gain change.

RFQ تماس
INA137UA - +/-6dB Audio Differential Line Receiver SOIC-8 | Texas Instruments
INA137UA

INA137UA - +/-6dB Audio Differential Line Receiver SOIC-8 | Texas Instruments

The Texas Instruments INA137UA is a single-channel audio differential line receiver with selectable gain of -6 dB (G = 1/2) or +6 dB (G = 2), specified for a maximum supply of +/-18 V (36 V total) and offered in an 8-pin SOIC package. It is designed to convert a balanced, ground-referenced audio differential source into a single-ended or differential output while rejecting common-mode noise picked up along long cable runs. An audio differential line receiver (also called a balanced audio receiver) is a special-purpose instrumentation-amplifier derivative whose job is to accept a two-wire balanced input pair, extract the differential signal, and strongly attenuate the common-mode voltage that accumulates on long unbalanced or balanced interconnects. In the signal-chain hierarchy it sits between the source (microphone, mixer, player) and the downstream ADC, codec, or line-output stage; electrically it is a differential receiver amplifier, which is a member of the larger op-amp family within signal-chain ICs and, ultimately, within analog semiconductors. The INA137 offers two fixed-gain operating points that are selected by simply reversing the input and feedback resistors: with the resistors in the datasheet's G = 1/2 configuration the receiver attenuates by -6 dB, and reversing them yields +6 dB, or G = 2. Because both gain settings use the same pins, a single PCB layout supports either an attenuating or a boosting balanced input without changing the footprint. The device also provides differential outputs so that the noise cancelled at the input can also be cancelled on the way to the next stage. Because the INA137 is a difference amplifier built around matched internal pairs, common-mode signals from long cables, motorised environments, and grounds at different potentials are rejected before they reach the output. The result is a receiver that preserves signal integrity in professional audio distribution, studio racks, and consumer home-theatre equipment where ground loops and hum are the dominant noise mechanism. Typical applications include balanced XLR input conditioning in mixers and preamplifiers, digital-console input strips, active speaker crossovers, line-level differential receivers in broadcast racks, and instrumentation-style front ends for audio ADCs. The SOIC-8 (DBV) package and the +5 V to +18 V single-supply, or +/-5 V to +/-18 V dual-supply operating range make it easy to use alongside modern converter-based signal chains. When laying out the board, keep the input traces short and symmetric, place the gain-setting resistors close to the package pins, and provide local bypassing on the supply pins. Avoid routing the differential pair alongside switching converter nodes, and use a solid ground plane so that the common-mode rejection capability of the part is not undermined by board-level ground mismatch. This page brings together the manufacturer datasheet, ordering information, drop-in pin-compatible alternatives in the same SOIC-8 footprint, a parameter-by-parameter comparison, and practical design notes that go beyond the raw datasheet tables, so engineers can qualify the part quickly and choose the right sibling device when a different gain or bandwidth is required.

RFQ تماس
INA141P - Precision G=10/100 Low-Power Amplifier | Texas Instruments
INA141P

INA141P - Precision G=10/100 Low-Power Amplifier | Texas Instruments

The Texas Instruments INA141P is a precision, low-power instrumentation amplifier with selectable gains of 10 and 100, low maximum offset voltage of 50 µV, and high minimum common-mode rejection of 117 dB. It operates from dual supplies up to ±18 V and is supplied in an 8-pin plastic DIP package. The device is designed for accurate differential-signal conditioning where low offset, low drift, and high common-mode rejection are important. An instrumentation amplifier is a differential-input analog IC that amplifies the voltage difference between two signals while rejecting signals common to both inputs. The INA141 uses a versatile three-op-amp architecture, placing it in the instrumentation-amplifier hierarchy within the broader amplifier and signal-conditioning categories. Its general-purpose design is suitable for industrial measurement, sensor interfaces, current sensing, and other circuits that require differential gain and accurate signal extraction. Key features include a maximum offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, accurate gain settings of 10 and 100, and maximum input bias current of 5 nA. The input stage is protected against voltages up to ±40 V, while the wide ±18 V supply range supports higher-amplitude measurement systems. The current-feedback input circuitry maintains wide bandwidth at high gain, reaching 200 kHz at a gain of 100 V/V according to the manufacturer datasheet. The INA141P is intended for precision analog front ends rather than high-speed signal processing. At gain 10 or 100, its differential amplification behavior helps reject common-mode interference from power systems, sensors, and long wiring. The low offset voltage and low thermal drift are especially useful when the amplified differential signal is small and system accuracy is determined by input-referred error rather than by the downstream converter resolution. Typical applications include current-shunt measurement, bridge-sensor signal conditioning, differential pressure sensing, industrial instrumentation, and low-level analog measurement. In these systems, the INA141P can amplify the difference between two sensor nodes while rejecting shared supply or ground disturbances. The exact input common-mode range, output swing, bandwidth, noise, and supply-current values must be confirmed against the manufacturer datasheet for the complete operating envelope. A key design consideration is to verify that the measured differential voltage, common-mode voltage, supply rails, and required output span remain within the device limits. Input protection helps manage overload conditions, but protection networks and external resistors should still be selected for the actual system. Decoupling capacitors should be placed close to the supply pins, and the source impedances should be balanced to preserve common-mode rejection and accuracy. This page synthesizes the verified Texas Instruments product information, the manufacturer datasheet, distributor listings, and cross-reference search results. It emphasizes verified INA141P capabilities, practical instrumentation-amplifier usage, and the need to confirm unreported electrical details before final design release.

RFQ تماس
INA141PA - Precision 10/100 V/V Instrumentation Amplifier | Texas Instruments
INA141PA

INA141PA - Precision 10/100 V/V Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA141PA is a precision, low-power instrumentation amplifier with selectable gains of 10 V/V or 100 V/V, supplied in an 8-pin plastic DIP package. It is designed for measuring small differential signals while rejecting common-mode noise and offset. The device provides low offset voltage of 50 µV maximum, low input bias current of 5 nA maximum, and high common-mode rejection of 117 dB minimum. Its input stage supports input protection to ±40 V, while its wide ±18 V supply range allows operation from both single-split and dual-supply systems. An instrumentation amplifier is a specialized amplifier category that combines differential input measurement, high input impedance, accurate gain setting, and strong common-mode rejection into one device. It sits between sensors, bridge transducers, and precision converters in the signal-chain hierarchy: instrumentation amplifier -> operational amplifier -> analog signal-processing IC. The INA141PA uses a three-op-amp instrumentation-amplifier architecture with current-feedback input circuitry. According to the Texas Instruments datasheet, this configuration maintains a bandwidth of 200 kHz even at a gain of 100 V/V. Key features include accurate gain selection, low offset drift of 0.5 µV/°C maximum, low quiescent current, and operation across a -40 °C to +85 °C temperature range. The 10 V/V and 100 V/V gain choices make the device useful for bridge sensors, biomedical instrumentation, current measurement, and industrial sensor interfaces where the signal is small relative to the common-mode voltage. The INA141PA is available in an 8-pin plastic DIP package, which is useful for through-hole prototypes, laboratory equipment, and legacy industrial boards. The DIP package also provides a straightforward mechanical format for socket-based designs. Its input protection rating of ±40 V helps protect the measurement inputs when external wiring or sensors can present transients beyond the normal operating signal range. Typical applications include strain-gauge and RTD bridge amplifiers, precision current shunt measurements, ECG and other biomedical instrumentation, sensor acquisition modules, and laboratory test equipment. The main design consideration is ensuring the common-mode voltage, supply rails, gain configuration, and input protection limits remain within the device specifications. Stable reference bypassing and careful grounding are also important when measuring microvolt-level signals. This page synthesizes the verified manufacturer information, package details, technical trade-offs, and drop-in replacement considerations to support faster component selection, PCB planning, and purchasing decisions.

RFQ تماس
INA141U - Precision Low-Power Instrumentation Amplifier | Texas Instruments
INA141U

INA141U - Precision Low-Power Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA141U is a precision, low-power instrumentation amplifier with selectable gains of 10 V/V and 100 V/V, low offset voltage, and a wide common-mode input capability in an 8-pin SOIC package. According to the manufacturer product page, the INA141 family is designed for accurate differential signal conditioning where low power and compact size are important. The device uses a three-op-amp architecture and current-feedback input circuitry, providing useful bandwidth even at higher gain. An instrumentation amplifier is a specialized analog IC that amplifies the difference between two input voltages while rejecting signals common to both inputs. It belongs to the signal-conditioning and amplifier hierarchy, where instrumentation amplifiers are used ahead of analog-to-digital converters, measurement systems, sensors, and precision control equipment. The INA141U is intended for applications requiring high input impedance, accurate gain, low offset, and good common-mode rejection. Key verified characteristics include a gain accuracy of ±0.05% at G = 10, maximum low input bias current of 5 nA, minimum common-mode rejection of 117 dB, input protection to ±40 V, and a wide ±18 V supply range. The listed low offset voltage is 50 µV maximum, with low drift specified at 0.5 µV/°C maximum. These features make the device suitable for low-level differential measurements and applications where common-mode noise or input-source imbalance could otherwise reduce measurement accuracy. The INA141U combines a three-op-amp instrumentation-amplifier topology with a compact 8-pin SOIC package. The manufacturer describes current-feedback input circuitry and a bandwidth of 200 kHz at G = 100 V/V. This architecture supports a broader operating range than a simple resistive differential amplifier, although bandwidth, output swing, supply voltage, input common-mode range, and external gain-setting requirements must still be checked against the datasheet. Typical uses include sensor-interface signal conditioning, bridge excitation and readout, industrial measurement systems, biomedical instrumentation, audio and communication front ends, and precision analog-to-digital converter inputs. The INA141 is specified for a −40°C to +85°C temperature range in the 8-pin SOIC package, making it suitable for industrial equipment where extended commercial temperature operation is required. A practical design should begin by checking differential signal range, common-mode voltage, gain selection, supply headroom, output swing, and the input network. The gain is selected through the external resistor connected to the gain-setting pin according to the manufacturer application guidance. Keep input and feedback routing short, use a stable reference and resistor network where applicable, and provide decoupling close to the supply pins. This page consolidates verified manufacturer and distributor information, practical design guidance, application context, and strict source traceability. Because the supplied data does not include a verified public pinout table, pricing tiers beyond the provided marketplace indication, or verified drop-in substitute specifications, those fields are conservatively marked for validation rather than inferred.

RFQ تماس
INA141UA - G=10/100 Instrumentation Amplifier | TI
INA141UA

INA141UA - G=10/100 Instrumentation Amplifier | TI

The Texas Instruments INA141UA is a precision, low-power, three-op-amp instrumentation amplifier with selectable gains of 10 V/V or 100 V/V, 200 kHz bandwidth at a gain of 100, and an 8-pin SOIC package. It provides a maximum input offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, maximum input bias current of 5 nA, and minimum common-mode rejection of 117 dB. The input stage tolerates differential signals up to ±40 V. An instrumentation amplifier is a specialized amplifier that amplifies the voltage difference between two inputs while rejecting signals common to both inputs. The INA141 belongs to the amplifier hierarchy as an instrumentation amplifier, differential amplifier, and analog signal-conditioning IC. Its three-op-amp architecture provides accurate gain, high common-mode rejection, and balanced input impedance, making it useful for sensors whose outputs sit on a large common-mode voltage. The INA141 uses a versatile three-op-amp design and current-feedback input circuitry. This architecture maintains 200 kHz bandwidth even at the higher gain of 100 V/V. The available gain settings are implemented through simple pin connections without external gain-setting resistors, reducing component count and avoiding the tolerance and temperature errors introduced by a conventional external resistor network. Its low 5 nA maximum input bias current is particularly useful for high-impedance sources. The device is designed for precision measurement of low-level differential signals rather than for driving heavy loads. Its maximum offset voltage of 50 µV and drift of 0.5 µV/°C help maintain accuracy as temperature changes, while 117 dB minimum common-mode rejection suppresses common-mode noise and supply-related disturbances. The listed wide supply range of ±18 V accommodates dual-supply instrumentation systems, although operating-limit details should be confirmed in the manufacturer datasheet for a specific design. Typical applications include bridge-transducer signal conditioning, strain-gauge and pressure-sensor amplification, current-shunt measurement, isolated or high-voltage sensor interfaces, laboratory instrumentation, and precision industrial control systems. Input protection to ±40 V is useful when the sensor input can exceed the normal operating range, but system-level protection, grounding, and common-mode limits still require careful review. The principal design consideration is common-mode range. A high common-mode rejection ratio does not permit the input common-mode voltage to exceed the amplifier's linear input range. Designers should also place input and reference components for low noise, avoid long sensitive traces, and preserve the specified gain connections. Decoupling capacitors should be positioned close to the supply pins according to the manufacturer's layout guidance. This page combines verified manufacturer and distributor information with application guidance, drop-in candidate comparisons, and design checks. It also distinguishes verified INA141UA parameters from data that must be confirmed in the manufacturer datasheet, helping engineers select and implement the amplifier without relying on unverified substitute specifications.

RFQ تماس
INA141UA/2K5 - Precision 10/100 Instrumentation Amplifier | TI
INA141UA/2K5

INA141UA/2K5 - Precision 10/100 Instrumentation Amplifier | TI

The Texas Instruments INA141UA/2K5 is a precision, low-power, single-channel instrumentation amplifier with selectable gains of 10 V/V and 100 V/V, supplied in an 8-pin SOIC package. It operates from a minimum ±2.25 V supply to a maximum ±18 V supply, making it suitable for bipolar and single-supply signal-conditioning systems. The device is specified over a -40°C to +85°C temperature range and provides 200 kHz bandwidth at a gain of 100 V/V. An instrumentation amplifier is a specialized analog amplifier designed to amplify small differential signals while rejecting common-mode interference. The INA141 belongs to the broader hierarchy of instrumentation amplifiers, differential amplifiers, analog amplifiers, and integrated circuits. Its internal three-op-amp architecture and current-feedback input stage provide accurate gain control and useful bandwidth when operating at the higher 100 V/V gain setting. The device is commonly used where sensor outputs are small and the surrounding environment contains significant common-mode voltage. The main electrical features include low offset voltage of 50 µV maximum, low offset drift of 0.5 µV/°C maximum, low input bias current of 5 nA maximum, and a common-mode rejection ratio of 117 dB minimum. The inputs are protected against ±40 V signals, while the wide ±18 V supply capability supports higher-level analog systems. These characteristics make the amplifier suitable for bridge sensors, biomedical instrumentation, industrial measurement, and precision current sensing. The INA141 uses a three-op-amp instrumentation-amplifier architecture. Its gain can be selected at 10 V/V or 100 V/V rather than continuously adjusted, which simplifies calibration and reduces the number of external precision resistors required. Current-feedback input circuitry maintains 200 kHz bandwidth at gain 100, a useful result for applications that need faster settling than a conventional fixed-gain amplifier can provide. Input protection is important in industrial systems because transients can appear on sensor wiring before external protection networks fully respond. Typical applications include Wheatstone bridge amplification, pressure and load-cell signal conditioning, isolated or battery-powered measurement systems, and low-level differential sensor interfaces. The ±40 V input protection can improve robustness when a sensor line is exposed to accidental overload, while the 117 dB minimum common-mode rejection helps preserve accuracy when the signal is small relative to the common-mode voltage. The 8-pin SOIC package also supports compact, surface-mount PCB layouts. Designers should pay close attention to supply headroom, input common-mode range, output swing, and grounding when selecting the gain setting. Decoupling capacitors should be placed close to the supply pins, and the input and reference pins should be routed away from noisy switching nodes. The gain setting should be selected only after checking the available output swing and the sensor’s full-scale differential range. This page combines the Texas Instruments product information, verified distributor availability information, same-package replacement references, and practical engineering guidance to support component selection, PCB design, and sourcing. It also distinguishes the exact INA141UA/2K5 ordering code from related INA141 variants so engineers can evaluate fit without treating every related amplifier as an exact replacement.

RFQ تماس
INA141UAE4 - Precision Gain-10/100 Instrumentation Amplifier | TI
INA141UAE4

INA141UAE4 - Precision Gain-10/100 Instrumentation Amplifier | TI

The Texas Instruments INA141UAE4 is a low-power, precision three-op-amp instrumentation amplifier available in an 8-pin SOIC package. It supports fixed gains of 10 V/V and 100 V/V, operates from 2.25 V to 18 V, and combines a 250 V maximum input range with a slew rate of 4 V/µs. Current-feedback input circuitry maintains 200 kHz bandwidth at a gain of 100. An instrumentation amplifier is a specialized analog amplifier designed for low-level differential measurements. Its internal three-op-amp architecture measures the voltage between two input terminals while rejecting common-mode signals produced by ground offsets, motor noise, supply variation, or other shared disturbances. The INA141 belongs to the broader hierarchy of instrumentation amplifiers, precision analog amplifiers, and integrated amplifier ICs used for sensor and signal-chain conditioning. The principal gains are 10 V/V and 100 V/V, allowing the same device family to serve both moderate-amplification and high-amplification signal paths. A maximum input voltage of 250 V provides substantial headroom for high-voltage measurement systems. Its 200 kHz bandwidth at a gain of 100 V/V is particularly important because many instrumentation amplifiers lose usable bandwidth as gain increases; the current-feedback architecture helps the INA141 preserve bandwidth in higher-gain configurations. The three-op-amp structure provides matched internal resistors and a straightforward gain-selection arrangement, reducing the number of precision external components normally required by discrete implementations. The 2.25 V minimum supply voltage also supports lower-voltage analog systems, while the 18 V maximum supply rating accommodates conventional industrial supply ranges. The result is a compact analog front end for sensor signals where accuracy, common-mode rejection, and stable gain are more important than general-purpose op-amp flexibility. Typical uses include bridge excitation and readout, current-shunt measurement, industrial pressure and temperature sensing, biomedical instrumentation, and low-level differential signal acquisition. At gain 10 V/V, the amplifier is appropriate when moderate amplification and wider bandwidth are priorities. At gain 100 V/V, it is better suited to small sensor outputs where additional signal amplification is required, although circuit bandwidth, input common-mode range, output swing, and noise must still be checked against the actual operating point. PCB design should preserve the symmetry of the differential input routes and provide a quiet ground return for the analog signals. Decoupling capacitors should be placed close to the supply pins, while input and feedback connections should be kept short to minimize added noise and imbalance. System-level protection may also be needed because the input-voltage rating and the usable signal range are not the same specification. This page organizes the INA141UAE4 electrical characteristics, ordering information, package details, drop-in candidates, and application guidance into a design-focused reference. It also identifies where engineers must consult the manufacturer datasheet and pin-description table before assigning PCB tracks or committing to a replacement.

RFQ تماس
INA141UAG4 - 1 MHz Instrumentation Amplifier | Texas Instruments
INA141UAG4

INA141UAG4 - 1 MHz Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA141UAG4 is a precision, low-power instrumentation amplifier with fixed gains of 10 and 100, a bandwidth of 1 MHz, and an 8-SOIC package. It is designed for measuring small differential signals while rejecting common-mode noise, making it suitable for sensor interfaces, industrial measurement systems, and precision analog signal chains. The device also provides an input offset voltage listed as 250 µV and an input-referred noise density of 8 nV/√Hz in the manufacturer product information. An instrumentation amplifier is a specialized amplifier IC that measures the voltage difference between two inputs while suppressing signals common to both inputs. This is the low-dropout regulator hierarchy's measurement counterpart: INA141 belongs to the amplifier IC category, where the precision instrumentation-amplifier subclass provides high input impedance, internally configured gain, and strong common-mode rejection. Unlike a general-purpose operational amplifier, the INA141 integrates a complete differential measurement stage, reducing external matching requirements in many sensor and bridge circuits. The INA141 family supports two fixed-gain selections, G = 10 and G = 100, so engineers can choose between greater signal amplification and lower closed-loop bandwidth without changing the external gain-setting network. Its 1 MHz bandwidth supports moderate-frequency sensor signals. The listed 110 dB CMRR is particularly valuable when a small differential measurement is superimposed on a larger common-mode voltage, while the 8 nV/√Hz input-noise figure favors low-level instrumentation where source impedance is compatible with the input network. The INA141UAG4 uses an internal differential amplifier arrangement to preserve common-mode rejection and gain accuracy across its operating range. It is offered in an 8-SOIC package, allowing conventional surface-mount assembly and PCB routing. Because the product is listed as inactive by DigiKey, engineers should treat it as a legacy design and verify lifecycle availability, supported package variants, and any migration path before starting a new production run. Typical uses include bridge-transducer interfaces, pressure and strain measurements, current-shunt monitoring, and buffered sensing of low-amplitude differential signals. In these systems, the INA141 can amplify the difference between sensor lines while rejecting much of the common-mode voltage present on both lines. Its two gain choices are useful when a design must accommodate both relatively large and small differential signals without adding a programmable gain amplifier. The principal design consideration is to verify input common-mode range, output swing, supply requirements, gain-dependent bandwidth, and input bias-current effects against the manufacturer datasheet for the exact operating condition. The 8-SOIC footprint should be routed with short, symmetric input paths and a clean ground return to minimize conversion of external noise into differential error. Decoupling should follow the manufacturer's recommended application circuit. This product page combines the Texas Instruments product description with distributor lifecycle information and practical guidance for evaluating the INA141UAG4. It also identifies package-compatible alternatives and highlights the engineering differences that matter when an obsolete or inactive instrumentation amplifier must be replaced without changing the board layout.

RFQ تماس
INA143U - 5V/us G=10 Differential Amplifier | Texas Instruments
INA143U

INA143U - 5V/us G=10 Differential Amplifier | Texas Instruments

The Texas Instruments INA143U is a high-speed, precision difference amplifier with a 5 V/us slew rate, 250 uV maximum offset voltage, and selectable gain of 10 V/V or 0.1 V/V, housed in an 8-pin SOIC package. It is designed to amplify the voltage difference between two inputs while rejecting common-mode signals. A difference amplifier is a specialized operational-amplifier configuration that measures IN+ relative to IN- and can reject large common-mode voltages that would overwhelm a conventional single-ended amplifier. The INA143 family integrates precision, ratio-matched resistors to implement fixed gain without external feedback components. This simplifies differential sensing in instrumentation, current measurement, and signal-conditioning circuits while reducing resistor-matching errors. Verified headline specifications include a 5 V/us high slew rate, maximum offset voltage of 250 uV, low offset drift of 3 uV/C maximum, and gain error of 0.01%. The internal gain is selectable between G=10 and G=0.1. The low-cost design targets common-mode input operation from 0.1 V, while its high-speed behavior supports accurate reproduction of rapidly changing differential waveforms. The INA143U uses matched internal resistor networks to convert the differential input into a single-ended output. The manufacturer notes that the networks are ratio matched but may vary by up to 20% in absolute resistance. That distinction matters: ratio matching supports gain accuracy, but the absolute value should not be treated as a precision external resistor value. Input bias-current and offset-current effects are included in certain published noise and DC specifications. Typical uses include high-side current sensing in an industrial bus, differential sensor interfaces, analog measurement systems, power-converter feedback, and communications circuitry. Its 8-SOIC format supports conventional surface-mount assembly, although exposed-pad thermal performance is not specified in the provided data. The device operates from dual supplies described in the manufacturer materials, but a single-supply compatibility design must be verified from the complete datasheet before implementation. When laying out this amplifier, route differential inputs as a compact, matched pair and keep them away from switching-current paths. Place its input/output decoupling capacitors close to the supply and signal pins, and verify common-mode voltage, output swing, supply polarity, and settling performance under the intended load. The INA143U is appropriate when a matched G=10 or G=0.1 network, fast slew rate, and low offset are more important than external gain programmability. This page consolidates the verified manufacturer information, distributor availability, pricing snapshot, pin details, and application guidance for engineers comparing precision difference amplifiers. It also distinguishes verified drop-in candidates from functional alternatives, preventing unsupported substitutions.

RFQ تماس
INA143U/2K5 - 10V/V Differential Amplifier | Texas Instruments
INA143U/2K5

INA143U/2K5 - 10V/V Differential Amplifier | Texas Instruments

The Texas Instruments INA143U/2K5 is a precision difference amplifier with a fixed gain of 10 V/V, a slew rate of 5 V/µs, and an offset voltage of ±250 mV maximum, housed in an 8-pin SOIC package. It is designed to extract small differential signals from larger common-mode voltages in instrumentation, industrial-control, and signal-conditioning systems. A difference amplifier is a specialized operational-amplifier circuit that amplifies the voltage difference between two inputs while rejecting voltage shared by both inputs. The INA143 belongs to the instrumentation-amplifier and differential-amplifier hierarchy within the broader linear-IC and signal-conditioning categories. Its internal design provides fixed gain without requiring external gain-setting resistors, helping reduce component count and gain-setting variation. Key features include selectable gain configurations of 10 V/V or 0.1 V/V within the INA143 family, low gain error of 0.01% maximum, fast settling to 0.01% in 9 ms, and a wide supply range from ±2.25 V to ±18 V. These characteristics suit systems that require accurate differential measurement while operating from dual supplies. The listed operating-temperature range is −40 °C to +85 °C. The INA143U/2K5 uses internal resistor matching to establish its gain and supports operation with dual positive and negative supplies. Its 5 V/µs slew rate allows the output to respond quickly to input transitions, while the 9 ms settling specification supports applications that repeat measurements at a moderate rate. The 8-SOIC package also provides a compact surface-mount option for industrial and analog signal-chain equipment. Typical uses include bridge-transducer interfaces, current-loop measurement, laboratory instrumentation, industrial sensor conditioning, and cancellation of common-mode noise in differential sensor outputs. When selecting a circuit, verify the input common-mode range, output swing, supply arrangement, and required settling time against the manufacturer datasheet. For PCB implementation, treat the input, feedback, reference, and supply connections as sensitive analog paths. Keep input traces short, use a stable reference connection when the output requires an offset, and decouple each supply rail close to the device. Avoid long copper runs between the amplifier and high-impedance sensor nodes to minimize coupled noise and capacitance-related settling changes. This product page combines the manufacturer specifications with package information, application guidance, and drop-in comparison options. The comparison material highlights the fixed gain, supply range, slew rate, offset, package, and temperature constraints that should be reviewed before replacing an existing INA143U/2K5 in a production design.

RFQ تماس
INA143UA - High-Speed Precision Difference Amplifier | Texas Instruments
INA143UA

INA143UA - High-Speed Precision Difference Amplifier | Texas Instruments

The Texas Instruments INA143UA is a high-speed precision difference amplifier with a slew rate of 5 V/us, 250 uV offset, selectable gains of 10 or 0.1, and an 8-pin SOIC package. It is designed for instrumentation and signal-conditioning systems that require accurate differential measurement, high common-mode rejection, and fast response. A difference amplifier measures the voltage difference between two input signals while rejecting common-mode voltage. The INA143UA belongs to the instrumentation-amplifier and precision-amplifier hierarchy: it uses an internal differential amplifier to convert a small difference between input voltages into an amplified output. Its selectable gain supports applications where either a large differential signal must be attenuated or a small signal must be amplified without excessive common-mode error. The main performance characteristics include a 5 V/us slew rate, 250 uV offset, and 150 kHz bandwidth. The INA143UA is specified for a single supply up to 36 V or a dual supply of plus or minus 18 V, according to the manufacturer product information. Its 80 dB common-mode rejection helps preserve signal integrity when both input terminals experience large common-mode signals. The INA143UA is suited to current sensing, bridge-sensor interfaces, industrial measurement, audio instrumentation, and precision signal conditioning. Its gain options allow the same device family to serve attenuation, gain-10, and gain-0.1 signal paths. The reference terminal provides a way to establish the output reference point in single-supply systems, while dual-supply operation permits bipolar output around ground. When designing around the INA143UA, verify input and output voltage limits, common-mode range, supply configuration, and stability requirements against the manufacturer datasheet. Keep sensitive input and reference connections short, provide local supply bypassing, and route high-current returns away from the amplifier ground. Input and output filtering should be selected carefully because excessive capacitance can affect bandwidth or stability. This page consolidates the manufacturer product information, package details, verified source links, drop-in alternatives, comparison fields, and practical design guidance for engineers evaluating the INA143UA in precision analog signal chains.

RFQ تماس
INA143UA/2K5 - 5V/us Precision Difference Amp | TI
INA143UA/2K5

INA143UA/2K5 - 5V/us Precision Difference Amp | TI

The Texas Instruments INA143UA/2K5 is a high-speed precision difference amplifier with 5 V/us slew rate, 250 uV offset, selectable gain of 10 or 0.1, and an 8-pin SOIC package. It accepts bipolar input signals and uses a laser-trimmed internal resistor network to provide accurate differential gain and high common-mode rejection. A difference amplifier is a specialized operational-amplifier circuit that amplifies the voltage difference between two input nodes while rejecting signals common to both inputs. The INA143 belongs to the instrumentation-amplifier and precision differential-amplifier hierarchy, combining an operational amplifier with matched internal resistors. This makes it suitable for sensing small differential voltages in industrial, instrumentation, and signal-conditioning systems without requiring a discrete resistor network. The principal features include a 5 V/us slew rate, 250 uV input offset, selectable gains of 10 and 0.1, and laser-trimmed resistors for accurate gain. The manufacturer identifies the device as a precision difference amplifier optimized for high-speed applications. Its differential architecture improves common-mode rejection, while the internal resistor network reduces component-count and calibration requirements compared with a discrete implementation. The INA143UA/2K5 is supplied in an 8-pin SOIC package marked D, with an operating temperature range of -40 C to +85 C. The UA ordering option uses a tape-and-reel format, and the /2K5 suffix denotes a 2500-unit reel. As a single-circuit device, it offers one amplifier per package and is intended for precision analog signal chains rather than high-channel-count systems. Typical uses include current-sense amplifier signal conditioning, bridge-sensor front ends, industrial measurement systems, medical instrumentation, and differential communications. Its selectable gain supports both 10:1 attenuation of larger differential signals and 10:1 amplification of smaller signals when the appropriate device configuration is selected. The high slew rate also makes it suitable for waveforms that must be amplified without excessive distortion. Designers should preserve the differential signal path, compare input and output swing against the actual operating voltage, and validate common-mode range at the selected gain. Because the gain choice changes input impedance and common-mode performance, the gain setting must be confirmed against the manufacturer’s pin and electrical tables before finalizing the PCB layout. This page combines manufacturer specifications, drop-in alternatives, application guidance, pin-level planning support, and a parameter comparison for engineers evaluating the INA143UA/2K5 in precision analog designs.

RFQ تماس
INA145UA - Programmable Gain Difference Amplifier | Texas Instruments
INA145UA

INA145UA - Programmable Gain Difference Amplifier | Texas Instruments

The Texas Instruments INA145UA is a programmable-gain difference amplifier with a gain range of 1 V/V to 1000 V/V, 500 kHz bandwidth, 86 dB CMRR, and 570 uA quiescent current in an 8-pin SOIC package. It accepts supply voltages from ±2.25 V to ±18 V and is designed for precision measurement of small differential signals. A difference amplifier is an operational-amplifier circuit that subtracts one input voltage from another and amplifies the resulting differential voltage while rejecting signals common to both inputs. The INA145 belongs to the precision difference-amplifier hierarchy, which includes instrumentation amplifiers and programmable-gain amplifiers used in current sensing, sensor interfaces, and diagnostic equipment. The INA145 integrates a precision operational amplifier with an on-chip resistor network. External resistors connected to its gain-control pins allow gains from 1 V/V to 1000 V/V. Its 500 kHz bandwidth supports higher-frequency measurements than purely static instrumentation amplifiers, while 86 dB common-mode rejection suppresses common-mode interference. The 570 uA quiescent current supports low-power designs, and the specified operating-temperature range is -40°C to +85°C. Electrically, the device is intended for differential signal conditioning where input common-mode range, gain accuracy, output swing, and supply voltage must be considered together. A wide supply range permits operation from low-voltage analog systems to higher-voltage industrial interfaces. Because the gain is set by external resistors, resistor tolerance and temperature coefficient directly influence gain accuracy and common-mode performance. Typical uses include shunt-current measurement in power converters, bridge-sensor signal conditioning, battery and power-system monitoring, medical instrumentation interfaces, and industrial current sensing. The 8-pin SOIC package is also convenient for designs that need an amplifier with a small footprint and conventional surface-mount assembly. Designers should calculate input and output common-mode limits for the selected gain and supply voltage, and should use precision gain resistors with suitable tolerance and temperature stability. Input filtering and careful layout are important when the source impedance is high or the measured signal contains switching noise. The component is available from distributors in stock, but one marketplace identifies the exact MPN as discontinued, so procurement plans should account for lifecycle risk. This product record combines verified manufacturer and distributor information, practical application guidance, lifecycle observations, and drop-in replacement research. It is designed to help engineers evaluate the INA145UA beyond a basic parametric listing while remaining explicit about any specification that requires confirmation from the manufacturer datasheet.

RFQ تماس
INA146UA - 100V/V High-Voltage Difference Amplifier | TI
INA146UA

INA146UA - 100V/V High-Voltage Difference Amplifier | TI

Texas Instruments INA146UA is a precision high-voltage, programmable-gain difference amplifier with gain up to 100 V/V, a 550 kHz bandwidth, and an 8-pin SOIC package. It operates from a single 4.5 V to 36 V supply or from dual ±2.25 V to ±18 V supplies. Its 570 µA quiescent current supports low-power instrumentation systems, while its 5 mV input offset specification supports accurate measurement of small differential signals. A difference amplifier is a voltage-feedback amplifier that amplifies the voltage difference between two inputs while rejecting voltage common to both inputs. The INA146 belongs to the precision difference-amplifier family within instrumentation amplifiers and signal-conditioning ICs. Its differential input architecture supports accurate attenuation of high differential voltages, rejection of high common-mode voltages, and compatibility with common signal-processing voltage levels. Key features include a ±15 V high common-mode voltage range, differential gain up to 100 V/V set by external resistors, and a 570 µA low quiescent current. The input common-mode range extends beyond both supply rails, providing inherent input protection and allowing the amplifier to operate when its inputs exceed the local supply voltages. The 5 mV offset and 550 kHz bandwidth balance precision and response speed. Technically, the INA146 uses external gain-setting resistors, allowing the gain to be programmed according to application requirements. This resistor-programmed architecture makes it suitable for measurement systems in which gain must be adjusted across multiple input ranges. The operating temperature range of −40 °C to +125 °C supports industrial equipment, while the single-circuit 8-SOIC package simplifies PCB layout and replacement. Typical applications include high-side current sensing, precision bridge and transducer excitation, industrial process measurement, battery monitoring, and instrumentation where inputs may exceed the amplifier supply rails. The common-mode rejection capability is especially useful when a small sensor signal is superimposed on a larger system voltage. Designers should verify input and output voltage limits, power dissipation, gain-resistor tolerance, and stability across the intended frequency range. Because the common-mode input range extends beyond the rails, PCB creepage, protection, and grounding remain important even though the device offers inherent input protection. External input protection may still be required for sustained overvoltage conditions. This page combines verified manufacturer and distributor information with a parameter comparison, drop-in alternatives, application guidance, and practical design notes to support faster component selection and implementation.

RFQ تماس