5M240ZM68C5N - MAX V CPLD, 192 Macro Cells, 68-BGA | Intel
MPN: 5M240ZM68C5N ✓ فعال5M240ZM68C5N نمای کلی
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits between simple SPLDs/PLDs and larger FPGAs in the programmable logic hierarchy. The MAX V family occupies the small-density, low-power segment, ideal for glue logic, I/O expansion, bus bridging, and power-up sequencing. Compared with FPGAs, MAX V CPLDs offer deterministic timing, no boot overhead, and lower static current, making them well suited to applications that require predictable response in microseconds rather than milliseconds.
Key features include 192 macro cells organized in 4 Logic Array Blocks (LABs), 240 logic elements, 4 global clocks, and an internal flash configuration block. The device supports in-system programmability via JTAG, hot-socket insertion, multiVolt I/O for interfacing with 1.5 V, 1.8 V, 2.5 V, 3.3 V, and 5 V buses, and an integrated user flash memory block for non-volatile user data. The 1.8 V core is paired with flexible I/O banks, simplifying mixed-voltage system design.
The MAX V architecture is built on a flash-based process that retains configuration through power cycles and is fully reconfigurable in-circuit. With a typical standby current in the microamp range and support for low-power operation modes, the 5M240ZM68C5N enables power-efficient designs without sacrificing deterministic logic response. The I/O structure supports LVCMOS, LVTTL, PCI, and SSTL standards.
Typical applications include I/O expansion and level shifting between mismatched voltage domains, bus interface bridging (e.g., parallel to serial), power-up sequencing and reset distribution, glue logic replacement for discrete 74-series gates, and board-level control state machines. Designers favor MAX V when instant-on behavior and deterministic propagation delay are required at low logic densities.
When designing with this device, pay close attention to the 68-ball Micro FBGA fan-out: route all four inner power/ground rings with adequate vias for thermal relief, and reserve JTAG access (TCK, TMS, TDI, TDO) on PCB test points for in-system reprogramming. Use the Quartus Prime design software for fitting, timing closure, and JTAG programming.
This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the 5M240ZM68C5N for both new designs and existing platform refreshes.
جایگزین‌های drop-in برای 5M240ZM68C5N — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای 5M240ZM68C5N (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Configuration Memory, Package, Programming Interface, Family, User Flash Memory.
5M240ZM68C4N
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←5M240ZM68A5N
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←5M240ZM100C5N
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←5M240ZM100I5N
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←5M160ZM68C5N
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←5M240ZM68C5N حداکثر مقادیر مجاز و مشخصات الکتریکی
| Series | MAX V |
| Family | MAX V (5M240Z) |
| Device Type | CPLD - Complex Programmable Logic Device |
| Architecture | Non-volatile flash-based |
| Macro Cells | 192 |
| Logic Elements | 240 |
| Logic Array Blocks (LABs) | 4 |
| Maximum Operating Frequency | 118.3 MHz |
| Core Supply Voltage | 1.8 V (1.71 V to 1.89 V) |
| I/O Banks | MultiVolt I/O, 1.5/1.8/2.5/3.3 V compatible |
| Global Clocks | 4 |
| User Flash Memory | Yes (integrated) |
| بسته‌بندی | 68-ball Micro FBGA (BGA-68) |
| نوع نصب | Surface Mount |
| دمای کاری | 0 °C to +85 °C (commercial) |
| Programming Interface | JTAG (IEEE 1149.1) |
| وضعیت RoHS | Compliant |
پیکربندی پین 5M240ZM68C5N
| پین A1 | I/O — User I/O - bank 1 |
| پین A2 | I/O — User I/O - bank 1 |
| پین A3 | I/O — User I/O - bank 1 |
| پین A4 | I/O — User I/O - bank 2 |
| پین A5 | I/O — User I/O - bank 2 |
| پین A6 | GND — Ground |
| پین B1 | I/O — User I/O - bank 1 |
| پین B2 | I/O — User I/O - bank 1 |
| پین B3 | I/O — User I/O - bank 1 |
| پین B4 | I/O — User I/O - bank 2 |
| پین B5 | I/O — User I/O - bank 2 |
| پین B6 | I/O — User I/O - bank 2 |
| پین C1 | TDI — JTAG Test Data In |
| پین C2 | I/O — User I/O - bank 1 |
| پین C3 | GND — Ground |
| پین C4 | I/O — User I/O - bank 2 |
| پین C5 | I/O — User I/O - bank 2 |
| پین C6 | TDO — JTAG Test Data Out |
| پین D1 | TCK — JTAG Test Clock |
| پین D2 | TMS — JTAG Test Mode Select |
| پین D3 | I/O — User I/O - bank 1 |
| پین D4 | I/O — User I/O - bank 2 |
| پین D5 | I/O — User I/O - bank 2 |
| پین D6 | VCCIO1 — I/O bank 1 supply |
| پین E1 | I/O — User I/O - bank 1 |
| پین E2 | I/O — User I/O - bank 1 |
| پین E3 | I/O — User I/O - bank 1 |
| پین E4 | GND — Ground |
| پین E5 | I/O — User I/O - bank 2 |
| پین E6 | VCCIO2 — I/O bank 2 supply |
| پین F1 | I/O — User I/O - bank 1 |
| پین F2 | I/O — User I/O - bank 1 |
| پین F3 | VCCINT — Core 1.8 V supply |
| پین F4 | I/O — User I/O - bank 2 |
| پین F5 | I/O — User I/O - bank 2 |
| پین F6 | I/O — User I/O - bank 2 |
| پین G1 | I/O — User I/O - bank 1 |
| پین G2 | I/O — User I/O - bank 1 |
| پین G3 | GND — Ground |
| پین G4 | I/O — User I/O - bank 2 |
| پین G5 | I/O — User I/O - bank 2 |
| پین G6 | I/O — User I/O - bank 2 |
| پین H1 | I/O — User I/O - bank 1 |
| پین H2 | I/O — User I/O - bank 1 |
| پین H3 | I/O — User I/O - bank 1 |
| پین H4 | VCCIO1 — I/O bank 1 supply |
| پین H5 | I/O — User I/O - bank 2 |
| پین H6 | GND — Ground |
| پین J1 | CLK0 — Global clock input 0 |
| پین J2 | I/O — User I/O - bank 1 |
| پین J3 | I/O — User I/O - bank 1 |
| پین J4 | I/O — User I/O - bank 2 |
| پین J5 | CLK1 — Global clock input 1 |
| پین J6 | I/O — User I/O - bank 2 |
| پین K1 | I/O — User I/O - bank 1 |
| پین K2 | I/O — User I/O - bank 1 |
| پین K3 | I/O — User I/O - bank 1 |
| پین K4 | GND — Ground |
| پین K5 | I/O — User I/O - bank 2 |
| پین K6 | I/O — User I/O - bank 2 |
| پین L1 | I/O — User I/O - bank 1 |
| پین L2 | I/O — User I/O - bank 1 |
| پین L3 | I/O — User I/O - bank 1 |
| پین L4 | I/O — User I/O - bank 2 |
| پین L5 | I/O — User I/O - bank 2 |
| پین L6 | I/O — User I/O - bank 2 |
| پین M1 | VCCIO1 — I/O bank 1 supply |
| پین M2 | I/O — User I/O - bank 1 |
| پین M3 | GND — Ground |
| پین M4 | I/O — User I/O - bank 2 |
| پین M5 | I/O — User I/O - bank 2 |
| پین M6 | VCCIO2 — I/O bank 2 supply |
| پین N1 | I/O — User I/O - bank 1 |
| پین N2 | I/O — User I/O - bank 1 |
| پین N3 | I/O — User I/O - bank 1 |
| پین N4 | VCCINT — Core 1.8 V supply |
| پین N5 | I/O — User I/O - bank 2 |
| پین N6 | I/O — User I/O - bank 2 |
کاربردهای معمول
5M240ZM68C5N مناسب است برای 6 کاربردs: I/O Expansion and Voltage Level Shifting, Bus Interface Bridging (Parallel to Serial), Power-up Sequencing and Reset Distribution, Glue Logic Replacement (74-series Consolidation), Board-level Control State Machines, Industrial Control and HMI Front-end.
I/O Expansion and Voltage Level Shifting
The 5M240ZM68C5N's MultiVolt I/O banks natively support 1.5 V, 1.8 V, 2.5 V, 3.3 V, and 5 V signaling on a per-bank basis, which makes it ideal for voltage-domain bridging between modern SoCs and legacy peripherals. With 192 macro cells and 4 LABs, it can implement wide bidirectional level shifters and bus-width converters in a single chip, replacing dozens of discrete 74LVC/74AVC buffers. Its 7 ns typical propagation delay is deterministic, so timing margin is predictable even at full I/O utilization across four banks. Pair it with the 74AVC4T245 as a companion for any signals that exceed the CPLD's I/O count.
پیشنهادی
Bus Interface Bridging (Parallel to Serial)
The 5M240ZM68C5N's 240 logic elements and 4 global clocks are well matched to bus-bridge state machines that adapt a parallel processor bus (e.g., 16/32-bit local bus) to a serial protocol such as SPI, I2C, or UART. The flash-based non-volatile configuration ensures the bridge is live at the first clock edge after POR, which is critical for SoC boot loads where the host expects the peripheral to be ready immediately. With fMAX of 118.3 MHz, the CPLD can comfortably clock-shift parallel data at tens of megahertz while presenting deterministic latency to the host processor.
پیشنهادی
Power-up Sequencing and Reset Distribution
Power-up sequencing is one of the canonical MAX V use cases, and the 5M240ZM68C5N's non-volatile flash configuration combined with deterministic logic delay lets it drive multi-rail enable signals within microseconds of VCC ramp. With 192 macro cells, the CPLD can implement 8-16 independent power-good timing chains using simple counter macros, each with programmable delay and watchdog retrigger logic. The 1.8 V core draws negligible quiescent current, so it adds essentially no overhead to standby budgets while replacing discrete RC timers and supervisors.
پیشنهادی
Glue Logic Replacement (74-series Consolidation)
Designers often replace dozens of discrete 74LVC/74HC gates, muxes, and flip-flops with a single MAX V CPLD to simplify PCB layout, reduce BOM cost, and gain design flexibility via in-system reprogrammability. The 5M240ZM68C5N with 192 macro cells is sized for mid-complexity glue logic, including address decoding, interrupt arbitration, register banks, and clock-tree gating. Quartus Prime synthesis provides deterministic fitter reports, so timing closure at 50-100 MHz is straightforward without manual floorplanning.
پیشنهادی
Board-level Control State Machines
For deterministic finite state machines that govern front-panel buttons, indicator LEDs, fan control, and watchdog handshaking, the 5M240ZM68C5N offers the right mix of macro-cell density and predictable timing. The flash-based fabric means the FSM is alive at first clock and survives brown-outs without external reset glue. With 4 global clocks the CPLD can service time-critical interrupts, periodic LED PWM, and asynchronous button-debounce counters without contention. Designers can re-program via JTAG in seconds during board bring-up.
پیشنهادی
Industrial Control and HMI Front-end
Within industrial control cabinets and human-machine interfaces (HMIs), the 5M240ZM68C5N serves as the deterministic glue between the application processor and field-side peripherals - keypads, indicator LEDs, segment displays, and opto-isolated I/O. The MultiVolt I/O banks can drive 5 V opto-couplers directly while simultaneously interfacing 1.8 V or 3.3 V SoC GPIOs, eliminating separate translator ICs. The commercial 0 °C to +85 °C temperature grade suits indoor cabinet environments, and the flash-based instant-on behavior survives noisy power cycles common in factory automation.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای 5M240ZM68C5N — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | 5M240ZM68C4N | 5M240ZM68A5N | 5M240ZM100C5N | 5M160ZM68C5N |
|---|---|---|---|---|---|
| Package | 68-ball Micro FBGA (BGA-68) | 68-ball Micro FBGA (BGA-68) - same | 68-ball Micro FBGA (BGA-68) - same | 100-pin TQFP - different | 68-ball Micro FBGA (BGA-68) - same |
| Brand | Intel | Intel | Intel | Intel | Intel |
| Family | MAX V (5M240Z) | MAX V (5M240Z) | MAX V (5M240Z) | MAX V (5M240Z) | MAX V (5M160Z) |
| Macro Cells | 192 | 192 | 192 | 192 | 128 (-33%) |
| Maximum Operating Frequency | 118.3 MHz | 118.3 MHz | 118.3 MHz | 118.3 MHz | 118.3 MHz |
| Core Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Operating Temperature | 0 to +85 C (commercial) | 0 to +85 C (commercial) | -40 to +125 C (extended) | 0 to +85 C (commercial) | 0 to +85 C (commercial) |
| Architecture | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash |
تفاوت‌های کلیدی
- Commercial temperature grade at the lowest density option (در مقابل5M240ZM68A5N)
- Smallest package option in the 5M240Z family (در مقابل5M240ZM100C5N)
- Higher macro-cell count than the lower-density 5M160Z die (در مقابل5M160ZM68C5N)
یادداشت‌های طراحی
The 68-ball Micro FBGA package uses 0.5 mm ball pitch, which is non-trivial to fan-out on a standard 4-layer PCB. Designers should plan for HDI PCB technology with microvias-in-pad or 4-wire laser-drilled vias. Reference Intel application note AN 466 (MAX V board design guidelines) for the recommended via pattern, keep-out zones, and decoupling capacitor placement. Each VCCIO and VCCINT ball pair should have a 100 nF X7R decoupling capacitor within 5 mm of the ball, with a 4.7 uF bulk cap on each supply plane.
Route the four global clocks (CLK0-CLK3) with controlled-impedance traces (typically 50 ohm single-ended) and keep them isolated from fast-switching I/O. Match trace lengths within a CLK-to-CLK tolerance of +/-50 mil to minimize skew across LABs. Place the JTAG chain (TCK, TMS, TDI, TDO) on the outer PCB layer for easy probing during bring-up, and include a 4-pin 0.1 inch header for the Altera USB-Blaster programmer. Reserve TEST pins per the device handbook if you intend to use the JTAG boundary-scan features.
Do not mix 5 V and 1.8 V signals on the same I/O bank - each VCCIO bank must be supplied at a single voltage. Designers often overlook the fact that MultiVolt I/O means per-bank, not per-pin, voltage selection. Also, JTAG ID codes differ between 5M240Z and 5M160Z dies, so a Quartus Prime project targeted at the 5M240ZM68C5N must be refit before programming onto a 5M160Z device. Finally, leave the nCONFIG pin tied high through a 1 kohm resistor; floating it can trigger unintended reconfiguration in noisy environments.
اطلاعات انطباق
RoHS and REACH compliant per LCSC product listing (C1521410). Commercial temperature grade is not AEC-Q100 qualified; for automotive-grade MAX V parts use the 'A' suffix (5M240ZM68A5N). Lead-free (Pb-free) confirmed by the MBGA ball finish specification.
