AD7485BST - 14-Bit 1 MSPS SAR ADC | Analog Devices
MPN: AD7485BST ✓ فعالAD7485BST نمای کلی
A successive-approximation ADC, commonly called a SAR ADC, converts an analog input into digital code by performing a sequence of comparisons against a reference voltage. The AD7485 belongs to the ADC hierarchy, which sits within data-acquisition and signal-conversion integrated circuits. Its SAR architecture provides predictable conversion timing and a compact serial interface, allowing sampled measurements to be transferred efficiently to a controller, DSP, FPGA, or data logger.
Key characteristics include 14-bit nominal resolution, single-channel conversion, throughput up to 1 MSPS, and serial data access. Factory trimming reduces DC error sources, including input nonlinearity, offset, and gain error. The low-noise, wide-bandwidth track-and-hold front end allows the converter to capture rapidly changing analog signals while preserving useful signal bandwidth. Normal-mode power dissipation of 70 mW supports low-power instrumentation without requiring a high-performance external converter.
The AD7485BST is particularly useful when designers need accurate sampling from a restricted analog input range. The serial interface reduces the number of parallel signal paths on a PCB and can help conserve board area in dense acquisition systems. Its 48-LQFP package also provides more pins than a basic single-channel converter, allowing the device to expose power, reference, analog input, digital interface, and control functions without multiplexing compromises.
Typical applications include industrial process monitoring, sensor signal acquisition, portable measurement instruments, medical monitoring equipment, and embedded control systems that sample moderate-bandwidth analog waveforms. In these systems, the AD7485 can sit between an analog front end and a digital processor, with its serial output handled by an SPI-compatible controller or dedicated data-capture logic.
PCB design should preserve the converter's analog signal integrity and provide stable reference and supply connections close to the device. Keep the analog input route short, place decoupling capacitors at the supply pins, and use a clean reference source with appropriate grounding. When timing the serial interface, account for acquisition time, conversion time, and data-transfer latency rather than assuming the maximum sample rate is available for every input condition.
This product page brings together the manufacturer's converter specifications, verified pricing evidence, package information, a controlled replacement assessment, and practical application guidance. The AD7485BST is best understood as a low-power, 14-bit SAR ADC for compact systems that need accurate single-channel sampling without a parallel data bus.
جایگزینهای drop-in برای AD7485BST — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
AD7485BSTZ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD7485BST حداکثر مقادیر مجاز و مشخصات الکتریکی
| ADC Type | Successive-approximation register ADC |
| رزولوشن | 14 bit |
| Number of Channels | 1 channel |
| Throughput Rate | Up to 1 MSPS |
| Input Signal Type | Single-ended analog input |
| Track-and-Hold Input Bandwidth | Greater than 40 MHz |
| رابط | Serial interface |
| Normal-Mode Power Consumption | 70 mW |
| Factory-Trimmed DC Accuracy | Low INL, offset, and gain errors |
| بستهبندی | 48-LQFP (7x7 mm) |
| نوع نصب | Surface mount |
راهنمای پیکربندی پین AD7485BST 48-lqfp (7x7 mm)
پیکربندی پین برای AD7485BST (پکیج 48-lqfp (7x7 mm)). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای AD7485BST.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
AD7485BST مناسب است برای 6 کاربردs: Industrial Process Monitoring, Portable Medical Monitoring, Sensor Signal Acquisition, Embedded Data Logging, Waveform Capture, Communication and RF Monitoring.
Industrial Process Monitoring
The AD7485BST fits industrial process-monitoring systems that must digitize a conditioned pressure, temperature, or level signal with 14-bit resolution. Its throughput rate of up to 1 MSPS provides ample margin for many slow sensor channels, while the serial interface reduces parallel routing across the controller board. Factory trimming minimizes offset and gain contributions, supporting repeatable measurements after system calibration. The 70 mW normal-mode consumption is valuable in distributed monitoring equipment with limited thermal capacity. Use a protected analog front end, anti-alias filtering, and isolated grounding where the sensor is exposed to industrial transients.
پیشنهادی
Portable Medical Monitoring
The AD7485BST is appropriate for portable medical-monitoring equipment that converts a conditioned biosensor or instrumentation signal into a 14-bit digital result. Its low normal-mode power consumption of 70 mW helps limit thermal loading in battery-operated instruments, and the serial interface allows compact controller integration. The low-noise, wide-bandwidth track-and-hold circuit supports acquisition from higher-bandwidth physiological front ends that require anti-alias filtering. The converter should sit behind calibrated gain, protection, and filtering stages, with leakage, patient-safety isolation, and grounding handled by the complete analog system rather than by the ADC alone.
پیشنهادی
Sensor Signal Acquisition
The AD7485BST supports sensor acquisition boards that need consistent 14-bit conversion without a wide parallel data bus. A 1 MSPS maximum rate allows the design to sample fast transients as well as slowly changing sensor outputs, while the serial interface simplifies connection to an embedded controller or FPGA. Factory trimming helps lower fixed offset and gain error before calibration. The input network should present a stable drive to the track-and-hold stage and include filtering appropriate to the sensor bandwidth. For high-impedance sensors, leakage, settling time, guarding, and reference stability are critical system-level considerations.
پیشنهادی
Embedded Data Logging
The AD7485BST is well suited to embedded data loggers that acquire one analog channel and transfer each conversion through a serial interface. Its 14-bit resolution supports measurement accuracy, and its low 70 mW normal-mode power helps suit compact unattended equipment. The one-channel architecture simplifies synchronization and calibration compared with a multiplexed converter. A microcontroller can issue conversion commands, read serial data, and record scaled engineering units. Designers should account for serial timing, digital settling at the source, reference drift, and the number of samples required to average noise before making a measurement decision.
پیشنهادی
Waveform Capture
The AD7485BST can capture waveforms when the system requires 14-bit resolution and a sampling rate up to 1 MSPS. Its wide-bandwidth track-and-hold circuit can handle input frequencies above 40 MHz, allowing the front end to present a usable signal to the converter before acquisition. The design still needs sufficient analog bandwidth, gain, and anti-alias filtering so that aliasing and amplitude loss do not obscure the measured waveform. Serial readout reduces PCB trace count and makes the converter practical for compact instrumentation using an FPGA or dedicated digital controller.
پیشنهادی
Communication and RF Monitoring
The AD7485BST is applicable to communication or RF monitoring systems that sample an attenuated, filtered detector or measurement signal. The track-and-hold input bandwidth exceeding 40 MHz and the 1 MSPS conversion capability allow it to capture selected envelope, power, or calibration measurements rather than the carrier directly. Its serial interface keeps the converter practical in a mixed-signal board containing a processor or FPGA. The RF detector, anti-alias filter, gain stage, and reference must provide adequate bandwidth and dynamic range. Designers should also verify that the selected 14-bit converter meets the required amplitude resolution after all analog losses.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای AD7485BST — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | AD7485BSTZ |
|---|---|---|
| Package | 48-LQFP (7x7 mm) | 48-LQFP (7x7 mm) |
| Brand | Analog Devices | Analog Devices |
| Resolution | 14 bit | 14 bit |
| ADC Architecture | Successive-approximation register ADC | Successive-approximation register ADC |
| Number of Channels | 1 channel | 1 channel |
| Throughput Rate | Up to 1 MSPS | Up to 1 MSPS |
| Interface | Serial | Serial |
| Input Frequency Capability | Track-and-hold input frequencies above 40 MHz | Track-and-hold input frequencies above 40 MHz |
| Factory-Trimmed DC Accuracy | Low INL, offset, and gain errors | Low INL, offset, and gain errors |
تفاوتهای کلیدی
- Same-footprint family replacement with unchanged conversion specifications (در مقابلAD7485BSTZ)
- Low normal-mode power supports compact data-acquisition systems (در مقابلAD7485BSTZ)
- Wide-bandwidth acquisition front end (در مقابلAD7485BSTZ)
یادداشتهای طراحی
Place the AD7485BST close to the signal source and keep the analog input route short. The track-and-hold input must see a low-impedance source with adequate settling behavior; long traces and parasitic capacitance can degrade acquisition accuracy. Use a ground plane that supports the analog return path, avoid switching-node routing beneath the converter, and separate noisy digital return currents from the reference and signal grounds. The manufacturer datasheet should govern the final decoupling and grounding arrangement.
Use the supply and reference connections specified by the manufacturer datasheet and place their decoupling components close to the associated device pins. Reference quality directly affects conversion accuracy, so avoid routing the reference through digital switching paths and provide local return-current control. Estimated normal-mode dissipation is 70 mW; this figure is a manufacturer specification rather than a maximum-loss calculation. Confirm worst-case supply, reference, and ambient conditions before sizing copper and thermal margins.
Treat the analog input as a precision acquisition path even though the converter supports input frequencies above 40 MHz. Include an anti-alias filter and verify source settling at the selected sampling rate. The serial interface reduces parallel-bus routing, but digital timing still requires adequate signal-integrity margin across board and cable distances. Confirm acquisition time, conversion time, clock period, and data-transfer timing from the official datasheet before fixing the control firmware.
Avoid treating the 1 MSPS headline rate as a guarantee that every input source can be sampled accurately. Input bandwidth, source impedance, reference stability, filtering, timing margins, and the acquisition interval all affect usable performance. Also verify the exact order code before layout approval: AD7485BST and AD7485BSTZ share the same 48-LQFP footprint, but their order-code treatment differs. Review the manufacturer ordering guide for temperature grade and delivery configuration.
اطلاعات انطباق
The verified product and distributor snippets do not explicitly state the compliance status of the exact AD7485BST order code. Confirm declarations, temperature grade, and automotive qualification using the current Analog Devices product documentation and ordering information.