Texas Instruments

ADS7817EC - 12-Bit 200kHz Differential SAR ADC | Texas Instruments

MPN: ADS7817EC ✓ فعال
100mV to 2.5V Vdss 8-pin VSSOP Package
حداقل سفارش: 1 |

ADS7817EC نمای کلی

The Texas Instruments ADS7817EC is a 12-bit, 200kHz sampling analog-to-digital converter with a high-impedance fully differential analog input, supplied in an 8-pin VSSOP package. It accepts a reference voltage from 100mV to 2.5V and provides a corresponding input-referred resolution between 49uV and 1.22mV. The device combines differential measurement, low power consumption, automatic power-down, and a compact package for precision signal-chain designs.

A sampling ADC, or successive-approximation-register ADC, converts a continuously changing analog voltage into a digital code through repeated internal comparisons. The ADS7817EC belongs to the ADC hierarchy within data-converter and signal-chain semiconductors. Its differential input is particularly useful when the measured signal must reject common-mode noise, while its high input impedance allows direct connection to sensors, resistive bridges, and other transducers without an input buffer.

The principal features include 12-bit resolution, a maximum sampling rate of 200kHz, and a flexible reference range of 100mV to 2.5V. The smallest reference voltage produces a finer input-referred step of 49uV, while the largest reference produces a 1.22mV step. Automatic power-down helps reduce consumption when conversions are infrequent, and the differential architecture supports measurement of signals centered around a common-mode voltage.

Internally, the ADS7817EC uses a successive-approximation conversion process and communicates through a serial interface. The small signal range makes reference selection a central part of the analog design: lowering the reference increases resolution near the input but reduces the available full-scale range. Designers should therefore balance sensitivity, headroom, input-common-mode limits, and conversion noise rather than selecting the reference solely from the converter’s nominal resolution.

Typical uses include battery-powered instrumentation, remote data acquisition, industrial sensor interfaces, precision bridge measurements, and low-power embedded systems. A differential sensor output can be connected directly to the analog inputs when its common-mode voltage and output span satisfy the device limits. The 200kHz sampling rate also permits measurement of slowly varying analog quantities and higher-frequency signals where the required aliasing and acquisition filtering can be implemented externally.

The main design consideration is preserving the differential signal path from the source to the converter. Short traces, symmetric routing, adequate input filtering, and careful grounding help limit errors and coupling. Reference bypass capacitors should be placed close to the device, and the analog and digital return paths should be arranged to minimize shared impedance, particularly when the converter operates beside switching circuitry.

This product page consolidates the Texas Instruments specifications, package information, pricing evidence, application guidance, and engineering design notes needed to evaluate the ADS7817EC. It also distinguishes true pin-compatible alternatives from reel-format and orderable-suffix variants so procurement and engineering decisions can be made without changing the circuit unintentionally.

جایگزین‌های drop-in برای ADS7817EC — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

هیچ جایگزین مستقیمی برای این محصول موجود نیست.

درخواست جایگزین

ADS7817EC حداکثر مقادیر مجاز و مشخصات الکتریکی

رزولوشن 12 bit
نرخ نمونه‌برداری 200kHz
Architecture Successive-approximation-register (SAR)
Input Type Fully differential, high impedance
Number of Analog Inputs 1 differential input
Reference Voltage Range 100mV to 2.5V
Input-Referred Resolution at 100mV Reference 49uV
Input-Referred Resolution at 2.5V Reference 1.22mV
Power-Down Automatic power-down
بسته‌بندی 8-pin VSSOP
نوع نصب Surface mount

راهنمای پیکربندی پین ADS7817EC 8-pin vssop

پیکربندی پین برای ADS7817EC (پکیج 8-pin vssop). این قطعه آنالوگ دارای پین‌های ورودی، خروجی و تغذیه است. برای پیکربندی‌های پین offset null، جبران‌سازی و فعال‌سازی به دیتاشیت سازنده مراجعه کنید. ایده‌آل برای مدارهای شرطی‌سازی سیگنال و تقویت‌کننده.

نمودار پین‌آوت پکیج 8-pin vssop برای ADS7817EC

داده پین‌آوت تفصیلی موجود نیست برای ADS7817EC.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

ADS7817EC مناسب است برای 6 کاربردs: Battery-Powered Instrumentation, Remote Data Acquisition, Precision Bridge Measurement, Precision Temperature Sensing, Industrial Process Control, Embedded Analog Monitoring.

🔋

Battery-Powered Instrumentation

The ADS7817EC fits battery-powered instruments that periodically measure low-level analog signals while keeping both circuit size and energy use under control. Its 12-bit SAR conversion, 200kHz maximum sampling rate, and automatic power-down support systems that alternate between active acquisition and low-power intervals. A 100mV reference can provide 49uV input-referred resolution when the transducer output has a narrow span, although the source must be designed so the differential signal and common-mode voltage remain within the converter’s input limits. Placing the input and reference bypass capacitors close to the device also reduces supply disturbance during conversion.

🌐

Remote Data Acquisition

The ADS7817EC is suitable for remote data-acquisition nodes that digitize a differential sensor output and transmit the result through a serial interface. Its high-impedance input can reduce the loading applied to the transducer, while the 200kHz sampling rate permits acquisition of rapidly changing inputs when the bandwidth is genuinely required. Differential routing reduces common-mode pickup along cable and sensor connections. For long or noisy interconnects, place suitable input filtering at the connector and preserve a symmetrical path to the converter so the measured difference is not corrupted by unequal traces or ground impedance.

🏭

Precision Bridge Measurement

The ADS7817EC can digitize outputs from resistive pressure, strain, and level bridges where excitation drift and common-mode noise would affect a single-ended measurement. A differential input measures the bridge imbalance directly, and the reference range of 100mV to 2.5V lets the designer match conversion resolution to the expected bridge output. A 100mV reference yields 49uV input-referred resolution, but it also limits the usable input span. The bridge excitation, input range, and converter common-mode limits should therefore be evaluated together before selecting the reference voltage and analog front end.

🌡️

Precision Temperature Sensing

The ADS7817EC can be used in temperature-measurement systems that require a compact ADC with a differential or low-side sensing arrangement. A 12-bit converter and adjustable reference provide flexibility for resistive sensors whose output depends on excitation and temperature. The automatic power-down feature supports portable equipment that samples infrequently, reducing the amount of time the conversion circuit remains active. Accurate results also depend on a quiet reference, stable sensor excitation, and careful handling of the sensor return signal; route the measurement path away from switching nodes and use filtering that preserves the required response time.

🏭

Industrial Process Control

The ADS7817EC can serve as the measurement front end in compact industrial controllers monitoring a differential process variable. Its 200kHz sampling capability is well above the rate needed by many slow temperature, pressure, or level loops, while the small VSSOP package leaves board area for control and interface circuitry. Differential input reduces sensitivity to shared noise in industrial wiring. Use an input protection strategy appropriate for the process environment, keep the reference local and bypassed, and establish the acquisition filter with both sensor-response time and converter timing in mind.

🧩

Embedded Analog Monitoring

The ADS7817EC is useful in embedded systems that combine a microcontroller with one or more analog measurements where board space and power are constrained. Its serial conversion architecture can reduce parallel routing compared with a wide-bus ADC, and the differential input supports compact sensor interfaces. The 200kHz maximum rate allows flexibility in sampling strategy, while automatic power-down can lower activity between measurements. The host processor must accommodate the converter’s serial timing and control sequence, and the analog section should use a short return path, local reference decoupling, and input components selected for the required bandwidth.

خلاصه محصولات پیشنهادی

ADS7817EC Texas Instruments استفاده‌شده در: Battery-Powered Instrumentation, Remote Data Acquisition, Precision Bridge Measurement, Precision Temperature Sensing, Industrial Process Control, Embedded Analog Monitoring ADS7817EC/250 Same converter with a different orderable packaging code استفاده‌شده در: Battery-Powered Instrumentation, Precision Bridge Measurement, Industrial Process Control ADS7817EC/2K5 Orderable ADS7817 converter configuration استفاده‌شده در: Remote Data Acquisition, Precision Temperature Sensing, Embedded Analog Monitoring
What is the ADS7817EC?
The ADS7817EC is a 12-bit, 200kHz sampling analog-to-digital converter from Texas Instruments. According to the Texas Instruments ADS7817 product page, it uses a high-impedance fully differential input, supports reference voltages from 100mV to 2.5V, and is intended for transducers, remote data acquisition, and multichannel systems. It is packaged in an 8-pin VSSOP and includes automatic power-down for reduced consumption between measurements.
What is the input resolution of the ADS7817EC?
The ADS7817EC has a nominal resolution of 12 bits, with input-referred resolution ranging from 49uV to 1.22mV as the reference changes from 100mV to 2.5V. According to the Texas Instruments ADS7817 product page, the usable resolution depends directly on the selected reference voltage. A 100mV reference supports the finer 49uV input step, while a 2.5V reference supports a 1.22mV step and greater input range.
What is the sampling rate of ADS7817EC?
The ADS7817EC supports a maximum sampling rate of 200kHz. This conversion capability makes it appropriate for rapidly sampled instrumentation, remote sensing, and other analog systems that need more frequent readings than a slow-resolution acquisition system. According to the Texas Instruments ADS7817 product page, the converter is a 12-bit SAR ADC, so acquisition time, sampling rate, and external filtering should be evaluated together.
Why is the ADS7817EC differential input useful?
The fully differential input lets the converter measure the voltage difference between two input nodes, improving rejection of common-mode noise compared with a single-ended measurement. According to the Texas Instruments ADS7817 product page, the high-impedance differential input is suitable for direct transducer connections. The source output must still remain within the converter’s specified input and common-mode limits, and external filtering should preserve the differential relationship.
Where can I download the ADS7817EC datasheet PDF?
The official ADS7817 datasheet is available through the Texas Instruments product document link at https://www.ti.com/lit/gpn/ADS7817. It is the appropriate document for checking the pin description, electrical limits, timing, reference requirements, and application circuit before layout approval. Use the package-specific ordering information to confirm that the selected device corresponds to the 8-pin VSSOP configuration used on the board.
Where can I find the ADS7817EC pinout?
The ADS7817EC pinout is published in the pin-configuration section of the Texas Instruments ADS7817 datasheet at https://www.ti.com/lit/gpn/ADS7817. Use the package drawing associated with ADS7817EC when assigning signal names and PCB pads. The 8-pin VSSOP outline must not be confused with the SO-8 or MSOP-8 variants offered for the ADS7817 family.
What reference voltage should I use with ADS7817EC?
The ADS7817EC reference voltage should be selected from the supported 100mV to 2.5V range according to signal span, resolution, and common-mode requirements. According to the Texas Instruments ADS7817 product page, a 100mV reference yields 49uV input-referred resolution, whereas a 2.5V reference yields 1.22mV. A smaller reference improves resolution near zero but reduces available input headroom.
Does ADS7817EC support low-power operation?
Yes, the ADS7817EC includes automatic power-down, which is one of the features highlighted for battery-operated and remote acquisition systems. The Texas Instruments ADS7817 product page identifies low power and automatic power-down as core device characteristics. Exact operating and shutdown currents should be taken from the electrical-characteristics table for the selected supply voltage, because they depend on operating mode and conversion activity.
Where can I buy ADS7817EC online?
The ADS7817EC can be requested through the “Request a Quote” form on this XAIPART product page. Submit the exact ordering code, target quantity, and required packaging information so the order can be reviewed against the appropriate 8-pin VSSOP configuration. Quote requests are the appropriate route for current commercial availability, lot handling, and delivery scheduling for this exact MPN.
What is the current price of ADS7817EC?
Current commercial pricing for ADS7817EC should be obtained through the “Request a Quote” form on this XAIPART product page. The form supports an inquiry using the exact MPN and requested quantity, allowing the commercial offer to reflect current sourcing conditions. Do not treat a historical catalog amount as a firm quotation because market availability and volume requirements can change.
What is the lead time for ADS7817EC?
The current lead time for ADS7817EC depends on the requested quantity, package configuration, and supply status at the time of order. Submit a “Request a Quote” inquiry on this page with the required quantity and delivery schedule. The resulting quotation can establish the applicable lead time and any minimum-order quantity rather than relying on a generic timing statement.
Is ADS7817EC in stock?
Stock for ADS7817EC should be confirmed through the “Request a Quote” form on this XAIPART product page. Include the exact MPN, quantity, and target delivery date in the request. This provides a channel-specific availability response for the required order instead of presenting a potentially stale listing status as a guaranteed inventory quantity.
What can replace ADS7817EC?
The closest drop-in replacement must use the same 8-pin VSSOP footprint, preserve pin assignments, and remain within the converter’s key voltage, resolution, sampling-rate, and interface limits. No electrically qualified replacement should be selected from an orderable suffix or reel format alone. Use the manufacturer datasheet and the XAIPART cross-reference resources to verify a candidate before modifying a released PCB.
Is ADS7817EC suitable for battery-powered sensor systems?
The ADS7817EC is suitable for battery-powered sensor systems because it combines a 200kHz sampling rate, differential high-impedance input, low-power operation, and automatic power-down. According to the Texas Instruments ADS7817 product page, these characteristics suit transducers and battery-operated systems. The sensor output must stay within the analog-input and common-mode limits, and the reference choice must preserve sufficient signal headroom.
ADS7817EC vs ADS7817EB/250 - which is better for my design?
The correct choice between ADS7817EC and ADS7817EB/250 depends on package, temperature grade, electrical limits, and ordering format rather than conversion performance alone. The ADS7817EC is specified here in an 8-pin VSSOP configuration, while ADS7817EB/250 is a different orderable variant. Compare the package drawing, pin description, temperature range, and absolute maximum ratings in the Texas Instruments datasheet before considering a substitution.
When should I choose ADS7817EC over a larger ADC?
Choose ADS7817EC when a compact, low-power, 12-bit SAR measurement is sufficient and the source can use a fully differential input. Its 200kHz sampling rate supports rapid acquisition, while reference control from 100mV to 2.5V provides a direct trade between sensitivity and range. Select a higher-resolution or multi-channel converter when noise performance, sample count, bandwidth, or interface requirements exceed those of this device.
What are the key specifications of ADS7817EC that engineers should know?
The ADS7817EC is a 12-bit SAR ADC with a 200kHz sampling rate, one high-impedance fully differential input, and a 100mV-to-2.5V reference range. According to the Texas Instruments ADS7817 product page, input-referred resolution ranges from 49uV to 1.22mV. Other essential engineering details include automatic power-down, the 8-pin VSSOP package, electrical limits, timing, and pin assignments from the official datasheet.

داده‌های مرجع مهندسی برای ADS7817EC — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose ADS7817EC when the design needs a compact, low-power, 12-bit SAR ADC with a fully differential input and up to 200kHz sampling. It is particularly suitable for battery-powered instruments, remote acquisition, bridge sensors, and embedded analog monitoring. The most important sizing decision is the reference: 100mV provides 49uV input-referred resolution for narrow signals, while 2.5V provides 1.22mV resolution and more headroom. Before ordering any substitute, confirm the exact package, pin assignments, serial timing, electrical limits, temperature grade, and reference behavior. ADS7817EC/250 and ADS7817EC/2K5 are order-format variants rather than engineering alternatives. A functionally similar converter should be selected only when it preserves the 8-pin VSSOP land pattern and can meet the required resolution, conversion rate, power, noise, and application environment without board or firmware changes.

مقایسه با جایگزین‌ها

پارامتر این محصول
Brand Texas Instruments
Package 8-pin VSSOP
Resolution 12 bit
Sampling Rate 200kHz
Architecture Successive-approximation-register (SAR)
Input Type Fully differential, high impedance
Reference Voltage Range 100mV to 2.5V
Input-Referred Resolution 49uV to 1.22mV
Power-Down Automatic power-down

تفاوت‌های کلیدی

  • Compact differential measurement in an 8-pin package (در مقابلADS7817EB/250)
  • Flexible reference-controlled resolution (در مقابلADS7817EC/250)
  • Power management for intermittent acquisition (در مقابلADS7817EC/2K5)

یادداشت‌های طراحی

Route the two analog inputs as a close, approximately symmetrical pair and return both through the same ground reference plane. Place the input and reference bypass components directly beside their associated device pins, and keep the path from the sensor or signal source free of digital switching nodes. Differential symmetry helps preserve the intended voltage difference and reduces conversion error caused by unequal pickup.

Select the reference voltage by balancing input-referred resolution against available signal span. A 100mV reference provides 49uV input-referred resolution, while 2.5V provides 1.22mV. Confirm that the expected differential input, reference tolerance, and converter input limits remain valid across temperature and supply tolerance. Decouple the reference locally and verify the resulting noise against the smallest signal the design must resolve.

Do not treat ADS7817EC/250 and ADS7817EC/2K5 as different converter designs or use them to populate the alternatives list. These are orderable formatting differences for the ADS7817 family. A true replacement must preserve the 8-pin VSSOP footprint, pin functions, electrical limits, serial timing, and reference behavior; otherwise PCB and firmware changes are required.

Add input filtering appropriate to the source impedance and required bandwidth rather than copying a generic capacitor value. The filter should attenuate high-frequency noise without creating excessive settling time between conversions. Verify acquisition behavior at the highest intended sampling rate, keep the two differential channels similarly filtered, and account for any mismatch between the analog input impedance and the external components.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The Texas Instruments product material and official datasheet link are the authorities for package, electrical, environmental, and qualification details. Compliance declarations must be checked against the current manufacturer documentation for the exact ordering code.

تاریخ تأیید داده‌ها: 2026-11-14 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

ADS7817EC datasheet ADS7817EC datasheet pdf ADS7817EC pinout ADS7817EC specifications ADS7817EC 200kHz ADC ADS7817EC differential input ADS7817EC reference voltage ADS7817EC equivalent ADS7817EC replacement ADS7817EC VSSOP ADS7817EC price ADS7817EC stock Texas Instruments ADS7817EC ADS7817EC sensor interface ADS7817EC vs ADS7817EB/250

قطعات و اصطلاحات مرتبط

Texas Instruments ADS7817EC ADS7817EC/250 ADS7817EC/2K5 ADS7817EB/250 12-bit ADC analog-to-digital converter successive-approximation-register ADC SAR fully differential input high-impedance input 200kHz sampling rate 100mV reference voltage 2.5V reference voltage 49uV input-referred resolution 1.22mV input-referred resolution automatic power-down 8-pin VSSOP surface-mount package battery-powered instrumentation remote data acquisition industrial sensor interface signal-chain semiconductor data converter
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ