LM2904YPT - Dual 1.1MHz Op Amp | STMicroelectronics
MPN: LM2904YPT ✓ فعالLM2904YPT نمای کلی
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 belongs to the dual operational amplifier family, combining two amplifier channels in one package. Within the broader hierarchy, it is a low-power bipolar operational amplifier, a general-purpose amplifier IC, and a component within the wider analog signal-processing and semiconductor product category.
The LM2904YPT's two channels can be configured independently as inverting amplifiers, non-inverting amplifiers, comparators, buffers, or differential amplifier stages. Its 100 dB open-loop gain supports accurate signal amplification when closed-loop feedback controls the operating gain. The 1.1 MHz gain-bandwidth product establishes the bandwidth available for closed-loop operation, while the low-power characterization supports economical designs where amplifier power consumption is an important system constraint.
This dual architecture reduces component count and PCB area when a board requires two amplifier functions. It is particularly useful in sensor interfaces, analog signal conditioning, active filters, low-level audio paths, and general industrial control circuits. Because both channels share one package, designers should also evaluate common thermal and supply conditions rather than treating the two amplifier sections as completely independent systems.
Typical circuit implementation uses conventional negative feedback, input bias-current compensation where required, and suitable decoupling near the supply pins. Input and output signal levels must remain compatible with the device's operating limits, while stable feedback and suitable output loading are necessary to maintain expected performance. Signal-routing practices should minimize coupling between the high-gain inputs and nearby switching or digital nodes.
This page combines the exact LM2904YPT configuration, verified distributor listings, drop-in replacement analysis, package-level pin information, and practical design guidance. It helps engineers narrow the selection before requesting a quote for the dual low-power operational amplifier in its compact 8-TSSOP package.
جایگزینهای drop-in برای LM2904YPT — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای LM2904YPT (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Amplifier Type.
LM2904AYPT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2904YST
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2904YPT حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| نوع خروجی | Single-ended output per channel |
| Gain-Bandwidth Product | 1.1 MHz |
| Open-Loop Voltage Gain | 100 dB |
| Power Class | Low power |
| بستهبندی | 8-TSSOP |
| نوع نصب | Surface mount |
| Channel Count | 2 |
پیکربندی پین LM2904YPT
| پین 1 | OUT1 — Output of amplifier channel 1 |
| پین 2 | -IN1 — Inverting input of amplifier channel 1 |
| پین 3 | +IN1 — Non-inverting input of amplifier channel 1 |
| پین 4 | V- — Negative supply connection |
| پین 5 | +IN2 — Non-inverting input of amplifier channel 2 |
| پین 6 | -IN2 — Inverting input of amplifier channel 2 |
| پین 7 | OUT2 — Output of amplifier channel 2 |
| پین 8 | V+ — Positive supply connection |
کاربردهای معمول
LM2904YPT مناسب است برای 6 کاربردs: Industrial Sensor Signal Conditioning, Audio-Range Preamplifier, Active Filter and Filter Bank, Low-Power Analog Control Interface, Portable Measurement and Test Equipment, General-Purpose Analog Buffering.
Industrial Sensor Signal Conditioning
The LM2904YPT is suitable for conditioning outputs from sensors that produce relatively small analog voltages, such as temperature, pressure, and position sensing elements. Its two channels can provide gain or buffering stages around a bridge or transducer while keeping the implementation in one 8-TSSOP package. The 100 dB open-loop gain supports accurate closed-loop amplification, and the 1.1 MHz gain-bandwidth product provides useful bandwidth for many slow industrial signals. Layout should keep the amplifier inputs away from switching nodes and use a quiet reference ground to prevent coupling into the high-gain stage.
پیشنهادی
Audio-Range Preamplifier
The LM2904YPT can be used in low-level audio preamplifier, mixer, or active-filter stages where the signal bandwidth does not require a high-speed precision amplifier. Each channel provides 100 dB open-loop gain and 1.1 MHz gain-bandwidth product, allowing several common closed-loop gain configurations. The low-power dual format reduces component count in stereo or dual-channel analog paths. Input and output coupling, load compatibility, and output swing must be evaluated against the circuit, while careful grounding helps prevent feedback from producing audible instability.
پیشنهادی
Active Filter and Filter Bank
The LM2904YPT is appropriate for first-order active filters, amplifiers, and gain blocks within wider analog filter networks. Its 1.1 MHz gain-bandwidth product and 100 dB open-loop gain provide the operating characteristics needed for many low-frequency filtering tasks, while two channels can implement a matched filter section. Component tolerances and amplifier noise directly influence filter accuracy, so the feedback network should use suitable resistor and capacitor grades. Verify stability, output loading, and usable signal bandwidth with the final component values and source impedance.
پیشنهادی
Low-Power Analog Control Interface
The LM2904YPT can amplify control signals or buffer sensor outputs in embedded industrial and control systems where two analog channels are needed without the footprint of two separate single amplifiers. Its low-power characterization is useful in compact control boards, while the dual channel count simplifies signal routing and component inventory. Designers should calculate the required closed-loop gain against the 1.1 MHz gain-bandwidth product and confirm that output swing remains adequate for the controlled voltage range. Stable feedback and local supply decoupling are essential for reliable control-loop behavior.
پیشنهادی
Portable Measurement and Test Equipment
The LM2904YPT fits portable measurement equipment that needs two general-purpose amplifier channels for input conditioning, buffering, or differential amplification. The 8-TSSOP surface-mount package supports compact board layouts, and the 1.1 MHz gain-bandwidth product is suitable for many low- and mid-frequency measurement signals. To obtain useful accuracy, the signal source impedance, bias-current compensation, resistor tolerance, and output load should be considered together. High-impedance input nodes require careful board guarding and isolation from digital and switching circuitry.
پیشنهادی
General-Purpose Analog Buffering
The LM2904YPT can implement voltage followers or buffered signal paths where a source cannot directly drive the next stage. Two independent channels allow buffering of two related signals without using two packages, and the 100 dB open-loop gain provides high voltage-following gain under feedback. A voltage follower is especially useful for reducing loading effects in measurement chains. The design should maintain suitable output loading, avoid excessive output capacitance, and use short feedback paths to preserve stability and response in the 8-TSSOP layout.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای LM2904YPT — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | LM2904AYPT | LM2904YST |
|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-TSSOP | 8-TSSOP - same | 8-TSSOP - same |
| Amplifier Configuration | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
| Number of Channels | 2 | 2 | 2 |
| Mounting Type | Surface mount | Surface mount | Surface mount |
تفاوتهای کلیدی
- Two general-purpose amplifier channels in one compact package (در مقابلLM324ADR)
- Direct same-manufacturer 8-TSSOP replacement path (در مقابلLM2904AYPT)
- Defined low-frequency general-purpose performance (در مقابلLM2902N/PB)
یادداشتهای طراحی
Place the supply bypass capacitor close to pin 8, V+, and connect the negative supply return to pin 4, V-, with the shortest practical ground path. Keep amplifier input and feedback traces away from switching inductors, high-current outputs, and digital clock lines. In an 8-TSSOP layout, prioritize short feedback loops and a stable, uninterrupted ground reference because the device provides 100 dB open-loop gain and can amplify small unwanted coupling.
Do not select the LM2904AYPT or LM2904YST solely because the package matches. Compare the exact suffix-specific operating temperature range, supply limits, offset voltage, input bias current, slew rate, and output-drive requirements in the manufacturer datasheet. A mechanically compatible amplifier can still alter system accuracy, noise, stability, or environmental margin. Document the selected suffix in the schematic and BOM rather than treating all LM2904 variants as electrically interchangeable.
Use separate input and output routing where possible, and connect the feedback network close to the corresponding amplifier pins. High-impedance inputs may require guarding or a driven shield when leakage, humidity, or nearby digital leakage can affect the signal. Verify stable operation with the intended source impedance and capacitive load because the usable response depends on both closed-loop gain and the 1.1 MHz gain-bandwidth product.
اطلاعات انطباق
No definitive compliance declarations for the exact LM2904YPT suffix were established. Check the current manufacturer product page and the declarations associated with the selected ordering code before regulatory submission.