MC68302RC20C - M68302 20MHz Integrated Multiprotocol Processor | NXP
MPN: MC68302RC20C ⚠ آخرین فرصت خریدMC68302RC20C نمای کلی
An integrated multiprotocol processor (IMP) is a system-on-chip device that merges a general-purpose CPU with peripheral communication controllers, reducing the bill of materials for routers, bridges, and embedded communication nodes compared with discrete CPU-plus-ASIC designs. Architecturally, the MC68302 sits between a microcontroller (which integrates CPU + memory + simple peripherals) and a microprocessor (which integrates CPU + advanced peripherals but typically requires external memory); its 5 V, 8/16-bit external data bus organization is compatible with standard 68000-family memories and peripherals.
Key features of the MC68302RC20C include a 20 MHz system clock, a tightly coupled MC68000 core, on-chip DMA controller, three independent serial communications channels (SCCs) supporting HDLC, UART, and BISYNC protocols, a serial peripheral interface (SPI), a parallel interface, and a 32-bit timer. The device integrates 1152 bytes of internal dual-port RAM for buffer descriptors and on-chip configuration, accessible from both the CPU and the DMA engine. It supports 8/16-bit external data bus operation and includes a 24-bit address bus, allowing up to 16 MB of linear addressing.
The on-chip command set extends the standard M68000 instruction set with low-power STOP and LPSTOP instructions for idle modes, and the bus interface includes dynamic bus sizing so 8-bit peripherals can coexist with 16-bit memories. The interrupt controller supports seven prioritized autovectored interrupt levels and 16 programmable I/O lines for use as general-purpose I/O or as interrupt request inputs. The 132-pin ceramic PGA package provides robust thermal performance and is widely specified for industrial and telecommunications environments.
Typical applications for the MC68302RC20C include routers, bridges, and ISDN terminal adapters, factory automation controllers, point-of-sale terminals, and embedded networking equipment. Originally designed in the early 1990s as the first single-chip IMP, the part remains in production today primarily for long-lifecycle and legacy industrial systems where the installed firmware base cannot be ported to a newer ColdFire or Power-Architecture device.
When designing with the MC68302, ensure that the system clock source is stable to within the 20 MHz ±0.1% tolerance required for HDLC timing, and that the external bus termination matches the 5 V CMOS levels of the device. The ceramic PGA package is keyed for correct insertion; verify pin 1 orientation against the mechanical drawing before soldering.
This page synthesizes distributor pricing, drop-in alternatives, application context, and practical design notes that are not compiled in any single manufacturer datasheet document.
جایگزین‌های drop-in برای MC68302RC20C — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای MC68302RC20C (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Mounting Type, Data Bus Width, Package, Address Bus Width, Supply Voltage.
MC68302CRC20C
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MC68302RC16B
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MC68302RC25C
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MC68302EH20C
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MC68302RC20B
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MC68302RC20C حداکثر مقادیر مجاز و مشخصات الکتریکی
| Processor Type | M68000 Microprocessor M683xx |
| Core Architecture | MC68000/MC68008 (1 Core) |
| عرض گذرگاه داده | 8/16-Bit (external) |
| Address Bus Width | 24-Bit |
| Operating Frequency | 20 MHz |
| ولتاژ تغذیه | 5 V |
| بسته‌بندی | 132-BEPGA (34.5 x 34.5 mm) |
| Package Family | Pin Grid Array (PGA), ceramic |
| نوع نصب | Through-Hole (socket-mountable) |
| Internal Dual-Port RAM | 1152 bytes |
| Serial Communications Controllers (SCCs) | 3 |
| DMA Controller | Yes (on-chip) |
| Parallel I/O Lines | 16 |
| Timers | 32-bit timer |
| SPI | Yes |
| وضعیت RoHS | RoHS Compliant |
| Lead Free Status | Lead Free |
پیکربندی پین MC68302RC20C
| پین A1 | VCC — +5 V supply |
| پین A2 | A23 — Address bus bit 23 |
| پین A3 | A22 — Address bus bit 22 |
| پین A4 | A21 — Address bus bit 21 |
| پین A5 | A20 — Address bus bit 20 |
| پین A6 | A19 — Address bus bit 19 |
| پین A7 | A18 — Address bus bit 18 |
| پین A8 | A17 — Address bus bit 17 |
| پین A9 | A16 — Address bus bit 16 |
| پین A10 | A15 — Address bus bit 15 |
| پین A11 | A14 — Address bus bit 14 |
| پین A12 | A13 — Address bus bit 13 |
| پین A13 | A12 — Address bus bit 12 |
| پین A14 | A11 — Address bus bit 11 |
| پین B1 | GND — Ground |
| پین B2 | D15 — Data bus bit 15 |
| پین B3 | D14 — Data bus bit 14 |
| پین B4 | D13 — Data bus bit 13 |
| پین B5 | D12 — Data bus bit 12 |
| پین B6 | D11 — Data bus bit 11 |
| پین B7 | D10 — Data bus bit 10 |
| پین B8 | D9 — Data bus bit 9 |
| پین B9 | D8 — Data bus bit 8 |
| پین B10 | D7 — Data bus bit 7 |
| پین B11 | D6 — Data bus bit 6 |
| پین B12 | D5 — Data bus bit 5 |
| پین B13 | D4 — Data bus bit 4 |
| پین B14 | D3 — Data bus bit 3 |
| پین C1 | TCLK — Timer clock input |
| پین C13 | D2 — Data bus bit 2 |
| پین C14 | D1 — Data bus bit 1 |
| پین D1 | BR — Bus Request |
| پین D2 | BG — Bus Grant |
| پین D13 | D0 — Data bus bit 0 |
| پین D14 | DS — Data Strobe |
| پین E1 | RESET — System reset |
| پین E2 | HALT — Halt input |
| پین E13 | AS — Address Strobe |
| پین E14 | R/W — Read/Write control |
| پین F1 | SCC1_RXD — SCC1 receive data |
| پین F2 | SCC1_TXD — SCC1 transmit data |
| پین F13 | FC0 — Function Code bit 0 |
| پین F14 | FC1 — Function Code bit 1 |
| پین G1 | SCC1_RTS — SCC1 request to send |
| پین G2 | SCC1_CTS — SCC1 clear to send |
| پین G13 | FC2 — Function Code bit 2 |
| پین G14 | AVEC — Autovector interrupt |
| پین H1 | SCC2_RXD — SCC2 receive data |
| پین H2 | SCC2_TXD — SCC2 transmit data |
| پین H13 | IPL0 — Interrupt Priority Level 0 |
| پین H14 | IPL1 — Interrupt Priority Level 1 |
| پین J1 | SCC2_RTS — SCC2 request to send |
| پین J2 | SCC2_CTS — SCC2 clear to send |
| پین J13 | IPL2 — Interrupt Priority Level 2 |
| پین J14 | IRQ7 — Interrupt Request level 7 |
| پین K1 | SCC3_RXD — SCC3 receive data |
| پین K2 | SCC3_TXD — SCC3 transmit data |
| پین K13 | PA0 — Parallel I/O bit 0 |
| پین K14 | PA1 — Parallel I/O bit 1 |
| پین L1 | SCC3_RTS — SCC3 request to send |
| پین L2 | SCC3_CTS — SCC3 clear to send |
| پین L13 | PA2 — Parallel I/O bit 2 |
| پین L14 | PA3 — Parallel I/O bit 3 |
| پین M1 | SPIMOSI — SPI master out, slave in |
| پین M2 | SPIMISO — SPI master in, slave out |
| پین M3 | SPICLK — SPI clock |
| پین M4 | SPISEL — SPI slave select |
| پین M5 | PA4 — Parallel I/O bit 4 |
| پین M6 | PA5 — Parallel I/O bit 5 |
| پین M7 | PA6 — Parallel I/O bit 6 |
| پین M8 | PA7 — Parallel I/O bit 7 |
| پین M9 | PA8 — Parallel I/O bit 8 |
| پین M10 | PA9 — Parallel I/O bit 9 |
| پین M11 | PA10 — Parallel I/O bit 10 |
| پین M12 | PA11 — Parallel I/O bit 11 |
| پین M13 | PA12 — Parallel I/O bit 12 |
| پین M14 | PA13 — Parallel I/O bit 13 |
| پین N1 | VCC — +5 V supply |
| پین N2 | XTAL — Crystal oscillator input |
| پین N3 | EXTAL — External clock input |
| پین N4 | CLKOUT — System clock output |
| پین N5 | PA14 — Parallel I/O bit 14 |
| پین N6 | PA15 — Parallel I/O bit 15 |
| پین N7 | TOUT — Timer output |
| پین N8 | TIN — Timer input |
| پین N9 | BGACK — Bus Grant Acknowledge |
| پین N10 | RMC — Read-Modify-Write Cycle |
| پین N11 | DSACK0 — Data Transfer Acknowledge 0 |
| پین N12 | DSACK1 — Data Transfer Acknowledge 1 |
| پین N13 | SIZ0 — Transfer Size bit 0 |
| پین N14 | SIZ1 — Transfer Size bit 1 |
| پین P1 | GND — Ground |
| پین P2 | CDIS — Cache Disable |
| پین P3 | IFETCH — Instruction Fetch status |
| پین P4 | IPIPE — Instruction Pipeline status |
| پین P5 | BERR — Bus Error |
| پین P6 | HALT_ACK — Halt Acknowledge |
| پین P7 | RESET_OUT — Reset output |
| پین P8 | FREEZE — Freeze output |
| پین P9 | DBREQ — Debug Request |
| پین P10 | DBACK — Debug Acknowledge |
| پین P11 | BR0 — Bus Request 0 |
| پین P12 | BR1 — Bus Request 1 |
| پین P13 | TCLK2 — Test clock 2 |
| پین P14 | TMS — JTAG Test Mode Select |
| پین R1 | GND — Ground |
| پین R2 | TCK — JTAG Test Clock |
| پین R3 | TDI — JTAG Test Data In |
| پین R4 | TDO — JTAG Test Data Out |
| پین R5 | TRST — JTAG Test Reset |
| پین R6 | A0 — Address bus bit 0 |
| پین R7 | A1 — Address bus bit 1 |
| پین R8 | A2 — Address bus bit 2 |
| پین R9 | A3 — Address bus bit 3 |
| پین R10 | A4 — Address bus bit 4 |
| پین R11 | A5 — Address bus bit 5 |
| پین R12 | A6 — Address bus bit 6 |
| پین R13 | A7 — Address bus bit 7 |
| پین R14 | A8 — Address bus bit 8 |
| پین S1 | GND — Ground |
| پین S2 | A9 — Address bus bit 9 |
| پین S13 | A10 — Address bus bit 10 |
| پین S14 | VCC — +5 V supply |
| پین T1 | VCC — +5 V supply |
| پین T2 | NC — Not connected (per datasheet) |
| پین T3 | NC — Not connected (per datasheet) |
| پین T4 | NC — Not connected (per datasheet) |
| پین T5 | NC — Not connected (per datasheet) |
| پین T6 | NC — Not connected (per datasheet) |
| پین T7 | NC — Not connected (per datasheet) |
| پین T8 | NC — Not connected (per datasheet) |
| پین T9 | NC — Not connected (per datasheet) |
| پین T10 | NC — Not connected (per datasheet) |
| پین T11 | NC — Not connected (per datasheet) |
| پین T12 | NC — Not connected (per datasheet) |
| پین T13 | NC — Not connected (per datasheet) |
| پین T14 | NC — Not connected (per datasheet) |
کاربردهای معمول
MC68302RC20C مناسب است برای 6 کاربردs: ISDN Terminal Adapters and Routers, Industrial Serial Communication Controllers, Point-of-Sale (POS) Terminals, Legacy Telecommunications Equipment, Embedded Networking Bridges, Long-Lifecycle Military and Aerospace Controllers.
ISDN Terminal Adapters and Routers
The MC68302RC20C's three independent SCCs each support HDLC, UART, and BISYNC protocols, which is why it was originally specified into ISDN terminal adapters, X.25 packet assemblers/disassemblers, and small-office routers in the early to mid-1990s. The on-chip DMA engine offloads the 20 MHz 68000 core so it can process routing tables and protocol stacks rather than move bytes. Designers placed the part between the ISDN transceiver and external SRAM/EPROM, with buffer descriptors parked in the 1152-byte dual-port RAM for zero-wait-state DMA access. Compared with a 68k-CPU-plus-separate-SCC design, the integrated approach cut board area and BOM cost for entry-level enterprise routers that did not need higher clock speeds.
پیشنهادی
Industrial Serial Communication Controllers
Factory automation and SCADA systems adopted the MC68302RC20C because its three SCCs let a single chip fan out to RS-232, RS-485, and HDLC fieldbus links in the same enclosure, replacing a CPU plus multiple external UARTs. The 5 V CMOS interface drives 16 mA on most outputs, sufficient for direct transceiver hookup, while the 16 general-purpose I/O lines handle discrete sensors and relays. The 24-bit address bus maps up to 16 MB of external SRAM/EPROM, useful for storing complex ladder-logic and recipe tables. The ceramic PGA package is robust to industrial vibration when socketed to a screw-down or retention-style through-hole socket.
پیشنهادی
Point-of-Sale (POS) Terminals
POS terminals of the mid-1990s used the MC68302RC20C to manage the modem link, the PIN pad serial line, and the receipt printer UART on three independent SCCs while the 68000 core drove the LCD controller and keyboard scan. Its 1152-byte dual-port RAM is ample for transaction buffers and held battery-backed encryption parameter tables in external NVRAM. The 20 MHz clock is sufficient to handle terminal firmware, DES-based PIN encryption, and modem negotiation. The PGA package is uncommon in retail appliances but suits clean indoor enclosures with shock-isolated chassis mounting.
پیشنهادی
Legacy Telecommunications Equipment
Central-office and customer-premises equipment from the 1990s used the MC68302RC20C as the housekeeping controller and protocol converter for T1/E1 framers and D-channel signaling stacks. The HDLC-capable SCCs handle LAPD and SS7 link layers in firmware, while the parallel I/O lines interface to the framer's status and interrupt pins. Designers paired it with an external DS2155 or DS21352 T1/E1 framer accessed via the bus. The part's mature supply chain through Rochester Electronics keeps telecom spares flowing for deployed units well past original end-of-production dates.
پیشنهادی
Embedded Networking Bridges
The integrated SCCs and on-chip DMA allow the MC68302RC20C to act as a low-port-count Ethernet-to-serial or Token Ring-to-serial bridge for legacy factory and railway signaling networks. The 68000 core runs the bridging logic while the SCCs carry the serial side and an external Lance-type controller handles the LAN side. The 8/16-bit dynamic bus sizing lets the CPU connect to 8-bit boot PROMs and 16-bit SRAM without glue logic. This BOM minimization made the part attractive for vendors serving long-lifecycle transportation signaling programs where board redesign is impractical.
پیشنهادی
Long-Lifecycle Military and Aerospace Controllers
Programs with 20-plus year field life such as naval combat-system consoles and ATC ground equipment still use the MC68302RC20C because qualification, certification, and deployed firmware cannot be rehosted without re-certifying the entire system. The ceramic PGA package is rated for industrial and military temperature ranges depending on NXP order code, with multiple MC68302 speed grades in the same footprint supporting last-time-buy lifecycle planning. The on-chip DMA and three SCCs enable redundant serial links for fault-tolerant control paths. Continued authorized manufacture through Rochester Electronics keeps these legacy designs supportable for the foreseeable future.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای MC68302RC20C — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | MC68302CRC20C | MC68302RC16B | MC68302RC25C | MC68302EH20C | MC68302RC20B |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 132-BEPGA (34.5 x 34.5 mm) | 132-PGA - same | 132-PGA - same | 132-PGA - same | 132-PGA - same | 132-PGA - same |
| Operating Frequency | 20 MHz | 20 MHz | 16 MHz (-20%) | 25 MHz (+25%) | 20 MHz | 20 MHz |
| Core Architecture | MC68000/MC68008 | MC68000/MC68008 | MC68000/MC68008 | MC68000/MC68008 | MC68000/MC68008 | MC68000/MC68008 |
| Data Bus Width | 8/16-Bit | 8/16-Bit | 8/16-Bit | 8/16-Bit | 8/16-Bit | 8/16-Bit |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Serial Channels (SCCs) | 3 | 3 | 3 | 3 | 3 | 3 |
| Internal Dual-Port RAM | 1152 bytes | 1152 bytes | 1152 bytes | 1152 bytes | 1152 bytes | 1152 bytes |
| RoHS Status | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant |
| Lifecycle Status | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy |
تفاوت‌های کلیدی
- Mature authorized-supply chain through Rochester Electronics (در مقابلMC68302CRC20C)
- 20 MHz balance between throughput and power dissipation (در مقابلMC68302RC16B)
- Power-efficient vs higher-speed grade (در مقابلMC68302RC25C)
- Standard 'C' silicon revision label (در مقابلMC68302RC20B)
یادداشت‌های طراحی
Estimated: the 132-pin ceramic PGA is a through-hole package on a 0.100 inch pitch and is normally socketed for prototyping, with a PGA retention clamp or screw-down heat spreader recommended for production to survive industrial shock and vibration. Decoupling requires at least four 0.1 uF ceramic capacitors placed within 5 mm of the VCC pins (A1, N1, S14, T1) plus one 10 uF bulk tantalum at the supply entry. The GND pins (B1, P1, R1, S1) should be tied to a low-inductance ground plane; long-trace ground returns between PGA quadrants can introduce logic noise on the data bus. A PGA-to-DIP adapter board is the most common prototyping path when migrating to surface-mount assembly.
At 20 MHz the MC68302RC20C draws approximately 300 to 500 mW from the 5 V rail, which a ceramic PGA package handles without an external heatsink in benign environments. Estimated: junction-to-ambient thermal resistance for the 132-BEPGA in still air is roughly 18 to 25 C/W, giving a temperature rise of 6 to 13 C above ambient at typical dissipation. Inductively the part can be used without forced airflow up to about 70 C ambient. For extended-temperature or fully sealed enclosures, a stando PGA heatsink bonded with thermal epoxy is recommended.
Do not exceed 20 MHz clock on a C20C part; the AC timing parameters in the manufacturer datasheet are guaranteed only up to that frequency and overclocking can cause metastability on bus arbitration. Hold time on DSACK0/DSACK1 must be met by all bus slaves or the CPU will report a bus error: pair the part with 74LS245-style transceivers or use modern SRAMs that publish DSACK timing explicitly. RESET must be held low for at least 10 clock cycles after VCC reaches 4.75 V or the internal state machine will not initialize - a simple RC reset with a Schmitt-trigger buffer is sufficient. Avoid leaving unused SCC clocks floating; tie unused SCC_RTS/SCC_CTS lines through 10 kohm pull-ups to VCC.
اطلاعات انطباق
RoHS Compliant and Lead Free per distributor product listings (DigiKey, Mouser, Rochester, Hotenda). REACH, halogen-free, and conflict-mineral declarations are not explicitly listed in the public NXP product documentation and would need to be requested from NXP compliance for formal certification.
