OPA847ID - 3.9GHz Ultra-Low-Noise Op Amp | Texas Instruments
MPN: OPA847ID ✓ فعالOPA847ID نمای کلی
An operational amplifier is an active analog component that provides voltage amplification and signal buffering within a feedback network. Voltage-feedback operational amplifiers use the inverting input as the primary high-frequency feedback node, making them suitable for closed-loop gains ranging from low-level instrumentation to high-speed communications. The OPA847 belongs to the broader hierarchy of analog amplifiers, signal-chain ICs, and power-management-independent semiconductor components.
The OPA847ID combines 3.9 GHz gain-bandwidth performance with 0.85 nV/√Hz input-noise voltage density. Its 18 mA supply current supports low-power operation compared with many wideband amplifiers, while the shutdown pin can disable the amplifier when power reduction is required. The device is designed for applications where preserving signal fidelity and bandwidth is more important than using a general-purpose precision amplifier.
Because the OPA847 is a voltage-feedback amplifier, feedback-network design, source impedance, output loading, and trace geometry determine practical performance. The manufacturer datasheet describes operation with resistive feedback and recommends careful attention to high-frequency stability and output loading. The 8-SOIC package provides a compact surface-mount implementation, but decoupling and layout discipline remain essential when using the amplifier at high bandwidth.
Typical uses include high-impedance instrumentation buffers, broadband transimpedance stages, RF and IF signal conditioning, communications receivers, video electronics, precision test equipment, and low-noise signal acquisition. The shutdown function is useful in portable or intermittently powered systems where the amplifier does not need to remain active continuously.
When placing the OPA847ID, keep power-supply bypass capacitors close to the supply pins, provide a low-inductance return path, and route high-speed feedback and signal traces away from noisy switching nodes. Confirm output loading and feedback resistor values against the datasheet before operating near the device's upper bandwidth range.
This product page combines the manufacturer's OPA847 documentation, distributor package information, operating specifications, practical layout guidance, and same-package replacement guidance. It helps engineers distinguish the OPA847ID from lower-bandwidth or noisier alternatives while keeping the focus on pin compatibility, bandwidth, noise performance, and application fit.
جایگزینهای drop-in برای OPA847ID — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای OPA847ID (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Primary Application.
OPA847IDR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
OPA847IDG4
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
OPA842IDR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD8018ARZ
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←AD8017ARZ
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←OPA847ID حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | Wideband voltage-feedback operational amplifier with shutdown |
| Gain-Bandwidth Product | 3.9 GHz |
| Input Noise Voltage Density | 0.85 nV/√Hz |
| جریان تغذیه | 18 mA |
| Shutdown Function | Yes |
| Feedback Topology | Voltage feedback |
| Circuit Count | 1 circuit |
| بستهبندی | 8-SOIC (SOIC-8) |
| نوع نصب | Surface mount |
پیکربندی پین OPA847ID
| پین 1 | NC — Not connected (per datasheet) |
| پین 2 | IN- — Inverting input |
| پین 3 | IN+ — Non-inverting input |
| پین 4 | V- — Negative supply |
| پین 5 | NC — Not connected (per datasheet) |
| پین 6 | OUT — Output |
| پین 7 | V+ — Positive supply |
| پین 8 | SD — Shutdown control |
کاربردهای معمول
OPA847ID مناسب است برای 6 کاربردs: Broadband Instrumentation Signal Conditioning, RF and IF Signal Chains, Communications Receiver Front Ends, High-Speed Test and Measurement, Low-Noise Video Electronics, Portable and Pulsed Analog Systems.
Broadband Instrumentation Signal Conditioning
The OPA847ID fits instrumentation front ends that need to preserve small signals while operating across a wide frequency range. Its 3.9 GHz gain-bandwidth product allows useful closed-loop amplification well beyond ordinary precision-op-amp bandwidth, while 0.85 nV/√Hz input-noise density helps reduce input-referred noise in measurements involving weak sensor or source signals. Use the device in a voltage-feedback configuration with resistor values selected from the manufacturer datasheet. Keep the feedback loop compact, provide local supply bypass, and use a continuous ground plane to prevent layout parasitics from degrading the measured response.
پیشنهادی
RF and IF Signal Chains
OPA847ID is appropriate for RF and IF conditioning stages requiring both bandwidth and low input noise. The 3.9 GHz gain-bandwidth product supports high-frequency closed-loop operation, while 0.85 nV/√Hz noise density helps avoid degrading weak receiver signals close to the amplifier input. Place the amplifier where the source and feedback connections are short, and verify the target gain against the datasheet stability guidance. If the source is not 50-ohm terminated, account for the effective load and reflection behavior in the overall signal path.
پیشنهادی
Communications Receiver Front Ends
The OPA847ID can be used in communications receivers where low-noise amplification and wide bandwidth are both important. Its 0.85 nV/√Hz input-noise voltage density supports weak-signal preservation, and its 3.9 GHz upper bandwidth leaves room for wideband IF or baseband stages. The 18 mA supply current is also relevant in portable receiver designs, although shutdown allows the amplifier to be disabled during inactive periods. Match the circuit to the intended frequency band, impedance, gain, and output-load requirements before releasing the layout.
پیشنهادی
High-Speed Test and Measurement
OPA847ID supports high-speed test and measurement systems that amplify low-amplitude signals without relying on narrow-band precision amplifiers. The 3.9 GHz gain-bandwidth product is useful for wideband probe buffers, pulse and waveform conditioning, and high-speed sensor interfaces. The amplifier's 0.85 nV/√Hz input noise helps retain signal-to-noise ratio, while the 18 mA supply current supports compact instrumentation. Use short feedback traces, minimize loop area, and isolate sensitive input routing from clock and switching circuitry to preserve practical bandwidth.
پیشنهادی
Low-Noise Video Electronics
OPA847ID can be used in video and other high-speed analog systems requiring low-noise amplification and wide bandwidth. The 3.9 GHz gain-bandwidth product is well suited to buffering and gain stages operating above the bandwidth of conventional audio amplifiers, while 0.85 nV/√Hz input noise helps maintain signal integrity. Keep the input and feedback paths short, terminate unused inputs according to the datasheet, and check output loading against the required video impedance. The device should be evaluated for the specific video standard, rise-time requirement, and output buffer topology.
پیشنهادی
Portable and Pulsed Analog Systems
The OPA847ID is useful in portable or intermittently operating analog systems because it combines a 3.9 GHz gain-bandwidth product with an 18 mA supply current and a shutdown function. When the signal chain is active, the amplifier can provide low-noise, wideband gain; when it is idle, the shutdown pin can reduce power consumption. Design the control logic so the amplifier is enabled only when signal integrity requirements are met, and verify startup behavior around the shutdown pin. Maintain short bypass-capacitor connections so the supply remains stable during rapid enable and disable transitions.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای OPA847ID — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | OPA847IDR | OPA847IDG4 | OPA842IDR | AD8018ARZ | AD8017ARZ |
|---|---|---|---|---|---|---|
| Package | 8-SOIC (SOIC-8) | 8-SOIC (SOIC-8) | 8-SOIC (SOIC-8) | 8-SOIC (SOIC-8) | 8-SOIC (SOIC-8) | 8-SOIC (SOIC-8) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices |
تفاوتهای کلیدی
- High bandwidth paired with low input noise (در مقابلOPA842IDR)
- Integrated shutdown capability (در مقابلAD8018ARZ)
- Low 18 mA supply-current specification (در مقابلAD8017ARZ)
یادداشتهای طراحی
Place the supply bypass capacitors immediately adjacent to the OPA847ID supply pins and connect them to a continuous ground plane. Keep the input, feedback, and output traces short, especially in high-gain or high-bandwidth layouts. Avoid placing sensitive input traces beneath or beside digital return paths and switching inductors. Because the device reaches 3.9 GHz, even small parasitic inductances and capacitance can materially alter closed-loop response.
Use the manufacturer voltage-feedback topology and recommended resistor values as the starting point for the signal chain. Check the output load, source impedance, and feedback network because the effective load can differ from the nominal circuit description. For RF or IF stages, use controlled impedance routing and avoid accidental capacitive loading on the inverting input. Confirm stability and bandwidth with the complete source, load, and feedback network rather than relying on the nominal gain-bandwidth figure alone.
The OPA847ID operates with 18 mA supply current according to the available manufacturer comparison information. Budget this current across the complete analog section and provide a supply capable of maintaining low noise under dynamic output conditions. If the shutdown function is used, define the enable state before signal-path activity and ensure the shutdown control is not left floating. Local decoupling and a low-impedance ground return are as important as the nominal supply capacity.
اطلاعات انطباق
The available distributor comparison material references RoHS and REACH information, but the current excerpts do not provide definitive compliance values for the exact OPA847ID ordering variant. Obtain current declarations from Texas Instruments or request them through the Request a Quote form.