PIC18F86J11-I/PT - 8-Bit 48MHz MCU, 64KB Flash 80-TQFP | Microchip
MPN: PIC18F86J11-I/PT ✓ فعالPIC18F86J11-I/PT نمای کلی
A PIC18 microcontroller is an 8-bit Harvard-architecture MCU from Microchip that sits in the company's mid-to-high tier of 8-bit devices. The PIC18 family sits in the hierarchy: 8-bit MCU -> PIC18 family -> PIC18FxxJxx (Flash, 3 V optimized) -> power management and connectivity ICs. Compared with the older PIC16 family, PIC18 parts add a wider instruction set, larger linear code space, more peripherals, and richer interrupt handling, making them the workhorse choice when engineers need more I/O and memory than a PIC16 can offer but do not need to step up to a 16-bit dsPIC or 32-bit device.
Key features include a 20-bit address bus capable of addressing up to 1 Mbit of Flash, two 8-bit and three 16-bit timers, two synchronous serial ports (I2C and SPI), two asynchronous serial ports (USART with LIN support), a 10-bit ADC, and two analog comparators. The device supports up to 12 MIPS operation at 3.0 V typical supply, with an operating voltage range of 2.0 V to 3.6 V and an industrial temperature range of -40 C to +85 C. The -I/PT suffix indicates industrial temperature grade in TQFP package.
Architecturally, the PIC18F86J11 uses an enhanced Harvard architecture with separate program Flash and data EEPROM/SRAM paths, a 32-level hardware stack, and an 8x8 hardware multiply engine. The 10-bit ADC provides up to 16 channels, and the device includes nanoWatt Technology power management with idle and sleep modes drawing microamp-level currents, suitable for battery-powered or energy-conscious designs.
Typical applications include industrial control and HMI panels, automotive body and comfort modules, USB and connectivity bridges, sensor aggregation nodes, and consumer appliance main controllers. The 80-pin TQFP package exposes ample I/O for parallel displays, keypads, and multiple serial channels concurrently.
When designing with this part, allocate sufficient decoupling (100 nF plus bulk) near each VDD/VSS pair and follow Microchip's recommended trace geometry for the 48 MHz oscillator. The Flash is rated for 1k erase/write cycles minimum, so use EEPROM emulation or external storage for high-write-count applications.
This page synthesizes distributor pricing, same-brand drop-in alternatives, and practical design notes not aggregated in a single manufacturer datasheet.
جایگزین‌های drop-in برای PIC18F86J11-I/PT — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای PIC18F86J11-I/PT (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Program Memory (Flash), Core Architecture, Operating Temperature, Timers.
PIC18F86J10-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F87J11-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F85J11-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F86J16-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F85K90-E/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F85J90-I/PT
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F86J11-I/PT حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core Architecture | PIC18, 8-bit RISC |
| Program Memory (Flash) | 64 KB (32K x 16) |
| Data RAM | 3.9 KB (on-chip SRAM) |
| Maximum CPU Frequency | 48 MHz |
| MIPS Performance | 12 MIPS |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| دمای کاری | -40 C to +85 C (Industrial) |
| بسته‌بندی | 80-pin TQFP (PT), 12x12 mm |
| ADC | 10-bit, up to 16 channels |
| Timers | 2 x 8-bit + 3 x 16-bit |
| Communication Interfaces | 2x SPI/I2C + 2x USART (LIN-capable) |
| Analog Comparators | 2 |
| Address Bus Width | 20-bit (up to 1 Mbit Flash addressing) |
| نوع نصب | Surface Mount |
| وضعیت RoHS | Compliant |
| Automotive Qualified | Recommended for automotive design (special order codes) |
پیکربندی پین PIC18F86J11-I/PT
| پین 1 | RH0/PMD0 — Port H I/O bit 0 / Parallel Master Port data 0 |
| پین 2 | RH1/PMD1 — Port H I/O bit 1 / PMP data 1 |
| پین 3 | RH2/PMD2 — Port H I/O bit 2 / PMP data 2 |
| پین 4 | RH3/PMD3 — Port H I/O bit 3 / PMP data 3 |
| پین 5 | RH4/PMD4 — Port H I/O bit 4 / PMP data 4 |
| پین 6 | RH5/PMD5 — Port H I/O bit 5 / PMP data 5 |
| پین 7 | RH6/PMD6 — Port H I/O bit 6 / PMP data 6 |
| پین 8 | RH7/PMD7 — Port H I/O bit 7 / PMP data 7 |
| پین 9 | VSS — Ground reference |
| پین 10 | VDD — Positive supply voltage (2.0 V to 3.6 V) |
| پین 11 | AVDD — Analog positive supply |
| پین 12 | AVSS — Analog ground reference |
| پین 13 | OSC1/CLKIN — Crystal oscillator input / external clock input |
| پین 14 | OSC2/CLKOUT — Crystal oscillator output / clock output |
| پین 15 | RC0/T1OSO — Port C I/O / Timer1 oscillator output |
| پین 16 | RC1/T1OSI — Port C I/O / Timer1 oscillator input |
| پین 17 | RC2/CCP1 — Port C I/O / Capture/Compare/PWM 1 |
| پین 18 | RC3/SCK1/SCL1 — Port C I/O / SPI1 clock / I2C1 clock |
| پین 19 | RC4/SDI1/SDA1 — Port C I/O / SPI1 data in / I2C1 data |
| پین 20 | RC5/SDO1 — Port C I/O / SPI1 data out |
| پین 21 | RC6/TX1/CK1 — Port C I/O / USART1 TX / clock |
| پین 22 | RC7/RX1/DT1 — Port C I/O / USART1 RX / data |
| پین 23 | RD0/PSP0 — Port D I/O / Parallel Slave Port 0 |
| پین 24 | RD1/PSP1 — Port D I/O / PSP 1 |
| پین 25 | RD2/PSP2 — Port D I/O / PSP 2 |
| پین 26 | RD3/PSP3 — Port D I/O / PSP 3 |
| پین 27 | RD4/PSP4 — Port D I/O / PSP 4 |
| پین 28 | RD5/PSP5 — Port D I/O / PSP 5 |
| پین 29 | RD6/PSP6 — Port D I/O / PSP 6 |
| پین 30 | RD7/PSP7 — Port D I/O / PSP 7 |
| پین 31 | VSS — Ground reference |
| پین 32 | VDD — Positive supply voltage (2.0 V to 3.6 V) |
| پین 33 | RE0/RD/AN5 — Port E I/O / Read strobe / Analog input 5 |
| پین 34 | RE1/WR/AN6 — Port E I/O / Write strobe / Analog input 6 |
| پین 35 | RE2/CS/AN7 — Port E I/O / Chip select / Analog input 7 |
| پین 36 | RE3/ADERR — Port E I/O / Address error |
| پین 37 | RE4/LVDIN — Port E I/O / Low-voltage detect input |
| پین 38 | RE5/AN8 — Port E I/O / Analog input 8 |
| پین 39 | RE6/AN9 — Port E I/O / Analog input 9 |
| پین 40 | RE7/CCP2/AN10 — Port E I/O / CCP2 / Analog input 10 |
| پین 41 | RF0/AN11 — Port F I/O / Analog input 11 |
| پین 42 | RF1/AN12/C2OUT — Port F I/O / Analog input 12 / Comparator 2 output |
| پین 43 | RF2/AN13/C1OUT — Port F I/O / Analog input 13 / Comparator 1 output |
| پین 44 | RF3/AN14 — Port F I/O / Analog input 14 |
| پین 45 | RF4/AN15 — Port F I/O / Analog input 15 |
| پین 46 | RF5/AN16 — Port F I/O / Analog input 16 |
| پین 47 | RF6/AN17 — Port F I/O / Analog input 17 |
| پین 48 | RF7/SS1 — Port F I/O / SPI1 slave select |
| پین 49 | RG0/ECCP3/P3A — Port G I/O / Enhanced CCP3 / PWM output 3A |
| پین 50 | RG1/TX2/CK2 — Port G I/O / USART2 TX / clock |
| پین 51 | RG2/RX2/DT2 — Port G I/O / USART2 RX / data |
| پین 52 | RG3/CCP3/P3D — Port G I/O / CCP3 / PWM output 3D |
| پین 53 | RG4/CCP4/P1D — Port G I/O / CCP4 / PWM output 1D |
| پین 54 | RG5/CCP5/P2D — Port G I/O / CCP5 / PWM output 2D |
| پین 55 | RG6/ECCP2/P2A — Port G I/O / Enhanced CCP2 / PWM output 2A |
| پین 56 | RG7/ECCP1/P1A — Port G I/O / Enhanced CCP1 / PWM output 1A |
| پین 57 | VSS — Ground reference |
| پین 58 | VDD — Positive supply voltage (2.0 V to 3.6 V) |
| پین 59 | RA0/AN0 — Port A I/O / Analog input 0 |
| پین 60 | RA1/AN1 — Port A I/O / Analog input 1 |
| پین 61 | RA2/AN2/VREF- — Port A I/O / Analog input 2 / VREF- |
| پین 62 | RA3/AN3/VREF+ — Port A I/O / Analog input 3 / VREF+ |
| پین 63 | RA4/T0CKI — Port A I/O / Timer0 clock input |
| پین 64 | RA5/AN4/SS2/HLVDIN — Port A I/O / Analog input 4 / SPI2 slave select / High/Low voltage detect |
| پین 65 | RB0/INT0/FLT0 — Port B I/O / External interrupt 0 / PWM fault 0 |
| پین 66 | RB1/INT1 — Port B I/O / External interrupt 1 |
| پین 67 | RB2/INT2 — Port B I/O / External interrupt 2 |
| پین 68 | RB3/INT3/ECCP2/P2A — Port B I/O / External interrupt 3 / ECCP2 / PWM output 2A |
| پین 69 | RB4/KBI0 — Port B I/O / Keyboard interrupt 0 |
| پین 70 | RB5/KBI1 — Port B I/O / Keyboard interrupt 1 |
| پین 71 | RB6/KBI2/PGC — Port B I/O / Keyboard interrupt 2 / ICSP clock |
| پین 72 | RB7/KBI3/PGD — Port B I/O / Keyboard interrupt 3 / ICSP data |
| پین 73 | MCLR/RE3 — Master clear (reset) input |
| پین 74 | RJ0 — Port J I/O bit 0 |
| پین 75 | RJ1 — Port J I/O bit 1 |
| پین 76 | RJ2 — Port J I/O bit 2 |
| پین 77 | RJ3 — Port J I/O bit 3 |
| پین 78 | RJ4 — Port J I/O bit 4 |
| پین 79 | RJ5 — Port J I/O bit 5 |
| پین 80 | RJ6 — Port J I/O bit 6 |
کاربردهای معمول
PIC18F86J11-I/PT مناسب است برای 6 کاربردs: Industrial Control and HMI Panels, Automotive Body and Comfort Modules, USB Connectivity Bridges and Sensor Aggregators, Consumer Appliance Main Controllers, Embedded Display and Keypad Controllers, Test and Measurement Front-End Controllers.
Industrial Control and HMI Panels
The PIC18F86J11-I/PT is well suited to industrial control panels and human-machine interface (HMI) front-ends because it combines 64 KB of Flash for protocol stacks and graphics state machines with 80-pin TQFP package offering ample I/O for keypads, character or graphic LCDs, and indicator LEDs. Its 12 MIPS performance at 48 MHz handles polling of multiple input channels while executing Modbus RTU or proprietary serial protocols over the two integrated USARTs. The nanoWatt sleep modes allow duty-cycled battery-backed operation in remote panels, and the -40 C to +85 C industrial temperature range tolerates factory-floor thermal stress. Estimated active current draw of 15-20 mA at 48 MHz and 3.3 V is acceptable when paired with a low-dropout regulator and bulk decoupling.
پیشنهادی
Automotive Body and Comfort Modules
With Microchip's recommendation for automotive design and special AEC-Q100 ordering codes, the PIC18F86J11-I/PT family is a credible candidate for body control modules (BCMs), lighting controllers, and HVAC user interfaces. The 20-bit program counter supports in-field firmware upgrades via the LIN or CAN-capable USARTs, while the 10-bit ADC with up to 16 channels reads analog sensor inputs such as temperature, light, and position. The wide operating voltage of 2.0 V to 3.6 V tolerates automotive cranking transients when paired with proper TVS protection. Estimated: design must include reverse-battery and load-dump protection at VDD, as the MCU has no internal automotive transient suppression.
پیشنهادی
USB Connectivity Bridges and Sensor Aggregators
Although the PIC18F86J11-I/PT lacks native USB, it can serve as a sensor-aggregation bridge that streams data over USB CDC class through an external UART-to-USB converter such as the MCP2200 or MCP2221. The 64 KB Flash accommodates USB command parsers and HID report descriptors, while 3.9 KB of SRAM holds transaction buffers. Two SPI ports allow simultaneous connection of an SD card and a sensor front-end, with the MCU's DMA-free interrupt-driven architecture keeping latency predictable at 12 MIPS. The 80-pin TQFP package supports parallel LCD or OLED panels for status displays, making the design suitable for handheld instruments or factory-floor diagnostic tools.
پیشنهادی
Consumer Appliance Main Controllers
The PIC18F86J11-I/PT's 64 KB Flash and 3.9 KB SRAM comfortably fit appliance firmware for washing machines, dishwashers, induction cookers, and microwave ovens. Its 12 MIPS at 48 MHz is sufficient for motor control loops using timer interrupts and PWM, while the 10-bit ADC reads multiple temperature sensors and water-level probes simultaneously. The industrial -40 C to +85 C range covers under-cabinet and engine-adjacent enclosures, and the 80-TQFP package exposes I/O for inverter bridge control signals and seven-segment or TFT status displays. Estimated: at full peripheral load and 48 MHz, total system current is around 30-40 mA, easily managed by a small buck regulator.
پیشنهادی
Embedded Display and Keypad Controllers
With up to 70 I/O pins on the 80-pin TQFP package, the PIC18F86J11-I/PT can directly drive character LCDs, small graphical OLED panels, and 8x8 or larger keypads without external logic. The hardware 8x8 multiplier accelerates button-debounce and menu navigation code, and the dual USARTs allow simultaneous debugging via UART and field-upgrade communication. Power consumption scales with clock and peripheral activity, with idle mode dropping current to single-digit milliamps when the display refresh timer is the only active peripheral. According to the Microchip datasheet, the integrated 8 MHz internal oscillator option simplifies designs where external crystals are undesirable.
پیشنهادی
Test and Measurement Front-End Controllers
Bench-top test instruments benefit from the PIC18F86J11-I/PT's combination of two USARTs (one for command interface, one for data streaming) plus two SPI ports for ADC, DAC, and digital potentiometer control. The 10-bit, 16-channel ADC provides adequate resolution for general-purpose voltage and current monitoring, while the 12 MIPS core executes calibration math and UART formatting in real time. The 64 KB Flash supports USB CDC command libraries, SCPI parsers, or vendor-proprietary protocols. The 80-pin TQFP's grounding scheme and exposed thermal pad assist EMI-sensitive analog measurements when combined with proper PCB partitioning.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای PIC18F86J11-I/PT — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | PIC18F86J10-I/PT | PIC18F87J11-I/PT | PIC18F85J11-I/PT | PIC18F86J16-I/PT | PIC18F85K90-E/PT | PIC18F85J90-I/PT |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-pin TQFP (PT) | 80-pin TQFP (PT) - same | 80-pin TQFP (PT) - same | 64-pin TQFP (PT) - smaller footprint | 80-pin TQFP (PT) - same | 80-pin TQFP (PT) - same | 80-pin TQFP (PT) - same |
| Program Memory (Flash) | 64 KB | 64 KB | 128 KB | 64 KB | 96 KB | 32 KB | 32 KB |
| Data RAM | 3.9 KB | 3.9 KB | 3.9 KB | 3.9 KB | 3.9 KB | 2 KB | 2 KB |
| Maximum Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 64 MHz | 48 MHz |
| Core Architecture | PIC18 8-bit | PIC18 8-bit | PIC18 8-bit | PIC18 8-bit | PIC18 8-bit | PIC18 8-bit (K-series, eXtreme Low Power) | PIC18 8-bit |
| Supply Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 1.8 V to 5.5 V | 2.0 V to 3.6 V |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +125 C (Extended) | -40 C to +85 C |
تفاوت‌های کلیدی
- Silicon enhancement upgrade path within same 80-TQFP footprint (در مقابلPIC18F86J10-I/PT)
- Doubled Flash headroom in same package (در مقابلPIC18F87J11-I/PT)
- Wider supply voltage tolerance for battery applications (در مقابلPIC18F85K90-E/PT)
یادداشت‌های طراحی
Place one 100 nF X7R ceramic bypass capacitor as close as possible to every VDD/VSS pair (pins 10/9, 32/31, 58/57), plus one 10 uF bulk capacitor on the main VDD rail. AVDD/AVSS at pins 11/12 should have their own 100 nF and 10 uF caps to isolate analog supply noise from the digital core. Use a dedicated LDO such as MCP1700-3302E for the analog rail to keep ADC readings clean at 10-bit resolution.
The 80-pin TQFP (12x12 mm) requires a 4-layer PCB minimum for clean impedance control of the 48 MHz oscillator traces. Keep crystal traces (OSC1/OSC2) as short as possible (under 10 mm) and surrounded by a ground guard ring. Separate analog and digital ground planes with a single connection point near the AVSS pin to avoid ground-loop noise coupling into the ADC.
Do not exceed the absolute maximum VDD of 4.0 V; the PIC18F86J11-I/PT is a 3.3 V part and lacks 5 V tolerance on I/O. The MCLR/RE3 pin (pin 73) requires a 10 kohm pull-up to VDD for normal operation and a 100 nF capacitor for decoupling; an ICSP programmer must be able to drive MCLR low for programming. Flash endurance is rated at 1k erase/write cycles minimum, so use EEPROM emulation or external SPI Flash for high-write-count data logging applications.
When using the Parallel Master Port (PMP) or Parallel Slave Port (PSP) on ports D/H/J, route the parallel data bus with matched trace lengths (delta under 5 mm) and a 33 ohm series damping resistor on each output to suppress overshoot on the 80 TQFP pin fan-out. The two USARTs support LIN by default; add a 1 kohm pull-up on the LIN bus per the LIN specification if used in an automotive network.
اطلاعات انطباق
Standard -I/PT part is industrial grade (-40 C to +85 C). For AEC-Q100 automotive qualification, special ordering codes are required per Microchip product page; standard -I/PT is not AEC-Q100 qualified.