STM32F105RCT6 - 32-bit Cortex-M3 256KB Flash MCU | STMicroelectronics
MPN: STM32F105RCT6 ✓ فعالSTM32F105RCT6 نمای کلی
What is a Cortex-M3 microcontroller? An ARM Cortex-M3 MCU is a 32-bit RISC processor core designed by ARM Holdings for embedded applications requiring deterministic real-time performance at low power. Positioned within the broader microcontroller taxonomy, it sits above 8-bit MCUs (8051, AVR) and below application processors in capability, while still delivering integer-only performance that suits motor control, sensing, and connectivity gateways. The STM32F1 series combines this core with ST's proprietary peripherals and a rich ecosystem of development tools.
The STM32F105RCT6 architecture pairs the Cortex-M3 core with a multi-channel 12-bit ADC (1 MSPS), up to seven timers (including a PWM timer suited to motor control), and an integrated USB OTG controller with on-chip PHY. A unique dual-bank Flash layout (2x128KB read-while-write) supports in-field firmware upgrades without service interruption. The 7-channel DMA controller offloads data movement, freeing the CPU for protocol stacks and control loops.
Connectivity is the STM32F105RCT6's defining strength relative to peers. The two CAN 2.0B controllers compliant with both standard 11-bit and extended 29-bit identifiers handle automotive and industrial bus rates up to 1 Mbit/s. Combined with USB OTG and multiple serial channels, the device suits gateway nodes bridging fieldbus, USB, and Ethernet networks on factory floors or in vehicle subsystems. The 72 MHz Cortex-M3 delivers 90 DMIPS (1.25 DMIPS/MHz), fast enough to run TCP/IP stacks or CANopen firmware without external coprocessors.
Typical applications include industrial PLCs, building automation gateways, USB-to-CAN bridges, motor-drive controllers, point-of-sale terminals, and low-power IoT edge nodes with wired connectivity. Compared with older 8-bit or 16-bit MCUs, the F105RCT6 collapses multi-chip designs into one part, lowering BOM cost and PCB area.
When designing, allocate decoupling capacitance near each VDD/VDDA pin, route the HSE crystal traces symmetrically with a ground guard ring, and use the boot pins (BOOT0/BOOT1) to enable system memory bootloader for USB DFU firmware update. The internal 8 MHz RC oscillator is accurate enough for many CAN applications, but a 32.768 kHz external crystal is recommended for RTC accuracy.
This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, including same-family variants such as STM32F107RCT6 and cross-brand substitutes from GigaDevice.
جایگزین‌های drop-in برای STM32F105RCT6 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای STM32F105RCT6 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Timers, ADC, USB, SRAM.
STM32F107RCT6
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←STM32F105RBT6
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
STM32F105R8T6
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
STM32F103RCT6
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←GD32F105RCT6
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
STM32F105RCT6 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core Architecture | ARM Cortex-M3 32-bit RISC |
| Maximum CPU Frequency | 72 MHz |
| CoreMark / DMIPS | 90 DMIPS (1.25 DMIPS/MHz) |
| Flash Memory | 256 KB |
| SRAM | 64 KB |
| Operating Voltage | 2.0 V to 3.6 V |
| بسته‌بندی | 64-pin LQFP |
| نوع نصب | Surface Mount |
| محدوده دمای کاری | -40 C to +85 C (grade 6) |
| CAN Interfaces | 2 x CAN 2.0B (1 Mbit/s) |
| USB | USB OTG Full-Speed with on-chip PHY |
| Ethernet | Not available on F105 (use F107 variant) |
| ADC | 2 x 12-bit, up to 1 MSPS |
| Timers | 4 x 16-bit general, 1 x 16-bit advanced, 2 x watchdog |
| DMA Channels | 7-channel DMA |
| I/O Count (approx.) | 51 GPIO |
| Communication Peripherals | 5x USART, 3x SPI, 2x I2C, 2x CAN, USB OTG |
| RoHS Compliance | Compliant |
پیکربندی پین STM32F105RCT6
| پین 1 | PE2 — GPIO PE2, TRACECLK (single pin) |
| پین 2 | PE3 — GPIO PE3, TRACED0 (single pin) |
| پین 3 | PE4 — GPIO PE4, TRACED1 (single pin) |
| پین 4 | PE5 — GPIO PE5, TRACED2 (single pin) |
| پین 5 | PE6 — GPIO PE6, TRACED3 (single pin) |
| پین 6 | VBAT — RTC backup supply |
| پین 7 | PC13 — GPIO PC13, RTC_TAMPER_RTC |
| پین 8 | PC14 — GPIO PC14, OSC32_IN (LSE) |
| پین 9 | PC15 — GPIO PC15, OSC32_OUT (LSE) |
| پین 10 | VSS_1 — Ground |
| پین 11 | VDD_1 — Digital supply 2.0-3.6V |
| پین 12 | OSC_IN — HSE crystal input or external clock |
| پین 13 | OSC_OUT — HSE crystal output |
| پین 14 | NRST — Reset input, active low |
| پین 15 | VSSA — Analog ground |
| پین 16 | VDDA — Analog supply 2.4-3.6V |
| پین 17 | PA0 — GPIO PA0, WKUP, ADC1_IN0, TIM2_CH1 |
| پین 18 | PA1 — GPIO PA1, ADC1_IN1, TIM2_CH2 |
| پین 19 | PA2 — GPIO PA2, USART1_TX, ADC1_IN2 |
| پین 20 | PA3 — GPIO PA3, USART1_RX, ADC1_IN3 |
| پین 21 | PA4 — GPIO PA4, SPI1_NSS, ADC1_IN4, USART2_CK |
| پین 22 | PA5 — GPIO PA5, SPI1_SCK, ADC1_IN5 |
| پین 23 | PA6 — GPIO PA6, SPI1_MISO, ADC1_IN6, TIM3_CH1 |
| پین 24 | PA7 — GPIO PA7, SPI1_MOSI, ADC1_IN7, TIM3_CH2 |
| پین 25 | PC4 — GPIO PC4, ADC2_IN14 |
| پین 26 | PC5 — GPIO PC5, ADC2_IN15 |
| پین 27 | PB0 — GPIO PB0, ADC1_IN8, TIM3_CH3 |
| پین 28 | PB1 — GPIO PB1, ADC1_IN9, TIM3_CH4 |
| پین 29 | PB2 — GPIO PB2, BOOT1 |
| پین 30 | PB10 — GPIO PB10, I2C2_SCL, USART3_TX |
| پین 31 | PB11 — GPIO PB11, I2C2_SDA, USART3_RX |
| پین 32 | VSS_2 — Ground |
| پین 33 | VDD_2 — Digital supply 2.0-3.6V |
| پین 34 | PB12 — GPIO PB12, SPI2_NSS, I2C2_SMBAI |
| پین 35 | PB13 — GPIO PB13, SPI2_SCK, USART3_CK |
| پین 36 | PB14 — GPIO PB14, SPI2_MISO, TIM1_BKIN |
| پین 37 | PB15 — GPIO PB15, SPI2_MOSI, TIM1_CH3N |
| پین 38 | PC6 — GPIO PC6, TIM3_CH1, I2S2_MCK |
| پین 39 | PC7 — GPIO PC7, TIM3_CH2, I2S2_CK |
| پین 40 | PC8 — GPIO PC8, TIM3_CH3, I2S2_CK_IN |
| پین 41 | PC9 — GPIO PC9, TIM3_CH4, I2S2_WS |
| پین 42 | PA8 — GPIO PA8, USART1_CK, TIM1_CH1, MCO |
| پین 43 | PA9 — GPIO PA9, USART1_TX, TIM1_CH2 |
| پین 44 | PA10 — GPIO PA10, USART1_RX, TIM1_CH3 |
| پین 45 | PA11 — GPIO PA11, CAN1_RX, USART1_CTS, USB_DM |
| پین 46 | PA12 — GPIO PA12, CAN1_TX, USART1_RTS, USB_DP |
| پین 47 | PA13 — GPIO PA13, JTMS/SWDIO |
| پین 48 | VSS_3 — Ground |
| پین 49 | VDD_3 — Digital supply 2.0-3.6V |
| پین 50 | PA14 — GPIO PA14, JTCK/SWCLK |
| پین 51 | PA15 — GPIO PA15, JTDI, SPI3_NSS |
| پین 52 | PC10 — GPIO PC10, UART4_TX, USART3_TX |
| پین 53 | PC11 — GPIO PC11, UART4_RX, USART3_RX |
| پین 54 | PC12 — GPIO PC12, UART5_TX, I2S2_WS_IN |
| پین 55 | PD2 — GPIO PD2, TIM3_ETR, UART5_RX |
| پین 56 | PB3 — GPIO PB3, JTDO, TIM2_CH2, SPI3_SCK |
| پین 57 | PB4 — GPIO PB4, NJTRST, SPI3_MISO |
| پین 58 | PB5 — GPIO PB5, I2C1_SMBAI, SPI3_MOSI |
| پین 59 | PB6 — GPIO PB6, I2C1_SCL, TIM4_CH1, USART1_TX |
| پین 60 | PB7 — GPIO PB7, I2C1_SDA, TIM4_CH2, USART1_RX |
| پین 61 | BOOT0 — Boot mode selection: 0=Flash, 1=System memory |
| پین 62 | PB8 — GPIO PB8, TIM4_CH3, I2C1_SCL, CAN1_RX |
| پین 63 | PB9 — GPIO PB9, TIM4_CH4, I2C1_SDA, CAN1_TX |
| پین 64 | VSS_4 — Ground (thermal pad not exposed on LQFP-64) |
کاربردهای معمول
STM32F105RCT6 مناسب است برای 6 کاربردs: Industrial CAN-to-USB Gateway, Building Automation Controller, USB-Connected Motor Drive Controller, Point-of-Sale Terminal Controller, Automotive Diagnostic Bridge, Industrial IoT Edge Sensor Hub.
Industrial CAN-to-USB Gateway
The STM32F105RCT6's dual CAN 2.0B controllers (each up to 1 Mbit/s) combined with USB OTG Full-Speed on the same die make it ideal for industrial gateway nodes that bridge USB host systems (PCs, HMIs) to CAN fieldbus networks. Place it between a USB upstream port and two isolated CAN transceivers (e.g. SN65HVD230); the 72 MHz Cortex-M3 runs CANopen or J1939 stacks concurrently with USB CDC, offloading data movement to the 7-channel DMA. Compared with a discrete CAN+USB MCU pair, this drops BOM cost and PCB area while remaining deterministic under 1 ms cycle times. Pin-compatible upgrade to STM32F107RCT6 adds Ethernet MAC for triple-protocol gateways.
پیشنهادی
Building Automation Controller
Building automation systems require robust wired connectivity and reliability at extended temperature. The STM32F105RCT6's two CAN buses handle BACnet or KNX subnets, while the five USART channels accept RS-485 sensor clusters via transceivers and the three SPI ports drive display or RFID peripherals. The -40C to +85C grade and dual-bank Flash support unattended firmware updates over the air via IP-based gateways. Engineers can repurpose the 1 MSPS 12-bit ADC to read temperature, humidity, and 4-20 mA transducers directly, reducing signal conditioning parts.
پیشنهادی
USB-Connected Motor Drive Controller
Brushless DC and stepper motor drives benefit from the STM32F105RCT6's advanced 16-bit PWM timer (with hardware break for safe commutation) and the high-speed 12-bit ADC (1 MSPS) for current sensing over USB. Connect a 5V USB host (PC or PLC) to the OTG FS port for tuning parameters over USB CDC, then drive a 3-phase inverter at variable speed using the timer's complementary PWM outputs with dead-time insertion. Compared with FOC implementations on smaller 8-bit MCUs, the 72 MHz/90 DMIPS headroom cuts loop time by 4-5x, enabling higher rotor speeds and finer torque control under load transients.
پیشنهادی
Point-of-Sale Terminal Controller
POS terminals need USB host for keyboard/printers, multiple serial channels for cash drawers and customer displays, and tamper-resistant firmware. The STM32F105RCT6's 256KB dual-bank Flash stores application and bootloader independently, while the 64KB SRAM buffers transactional data without overflow. USB OTG FS in host mode connects peripherals, and the two CAN channels interface to inventory/loyalty subsystem networks. The hardware cryptographic AES accelerator on the connectivity line (vs F103) secures cardholder data, supporting PCI compliance for retail point-of-sale designs.
پیشنهادی
Automotive Diagnostic Bridge
The two CAN 2.0B controllers with 11-bit and 29-bit identifier support make the STM32F105RCT6 ideal for OBD-II diagnostic bridges that read DTCs, freeze-frame data, and live PIDs from vehicle buses. Use one CAN for HS-CAN (500 kbit/s powertrain) and the other for MS-CAN (125 kbit/s body/comfort). USB OTG exposes diagnostics to a laptop running ECUs flashing or CANalyzer tools. The -40C to +85C industrial temperature range supports in-cabin placements; for engine bay installs verify against the higher-grade STM32F105RCT7 variant temperature spec (per ST suffix convention).
پیشنهادی
Industrial IoT Edge Sensor Hub
Wired Industrial IoT nodes often need multi-protocol aggregation. Place the STM32F105RCT6 between analog sensor inputs (via the dual 12-bit ADC), a local HMI on SPI, and an upstream PLC network on CAN. The 7-channel DMA offloads data movement from the CPU; the dual-bank 256KB Flash allows remote firmware updates for security patches. For nodes that also need wired IP networking, swap to STM32F107RCT6 without changing PCB layout. Compared with 8-bit alternatives, the Cortex-M3 core plus DMA cuts average current by 15-20% at equivalent throughput by sleeping more aggressively.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای STM32F105RCT6 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | STM32F107RCT6 | STM32F105RBT6 | STM32F105R8T6 | STM32F103RCT6 | GD32F105RCT6 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | GigaDevice |
| Package | LQFP-64 | LQFP-64 - same | LQFP-64 - same | LQFP-64 - same | LQFP-64 - same | LQFP-64 - same |
| Core | Cortex-M3 72 MHz | Cortex-M3 72 MHz | Cortex-M3 72 MHz | Cortex-M3 72 MHz | Cortex-M3 72 MHz | Cortex-M3 108 MHz |
| Flash | 256 KB | 256 KB | 128 KB | 64 KB | 256 KB | 256 KB |
| SRAM | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| CAN 2.0B | 2 channels | 2 channels | 2 channels | 2 channels | 1 channel | 2 channels |
| USB | OTG FS with PHY | OTG FS with PHY | OTG FS with PHY | OTG FS with PHY | FS Device only | OTG FS with PHY |
| Ethernet MAC | No | 10/100 MAC (MII/RMII) | No | No | No | No |
| Operating Voltage | 2.0-3.6 V | 2.0-3.6 V | 2.0-3.6 V | 2.0-3.6 V | 2.0-3.6 V | 2.6-3.6 V |
| Price (1 pc, USD) | 7.50 | 7.80 | 6.95 | 6.10 | 5.50 | 4.20 |
تفاوت‌های کلیدی
- Higher CAN bus count than baseline STM32F103 family (در مقابلSTM32F103RCT6)
- USB OTG host/device/dual-role with on-chip PHY (در مقابلSTM32F103RCT6)
- Industrial-grade temperature spec and dual-bank Flash (در مقابلGD32F105RCT6)
- GPIO count optimization for compact LQFP-64 (در مقابلSTM32F103RET6 (LQFP-64, similar peripherals))
یادداشت‌های طراحی
Estimated: At full 72 MHz CPU utilization across all peripherals including CAN, USB, and timers, internal core power dissipation is roughly 100-150 mW, well within LQFP-64's thermal envelope (theta_JA approximately 45-55 C/W on standard 2-layer JEDEC PCB per ST datasheet thermal tables). For sustained high ambient temperatures (>70 C), adding a small copper pour under the exposed thermal land (where present) or top-side copper heatsink helps maintain margin. Industrial designers should monitor junction temperature via the built-in sensor channel for long-term reliability.
Place decoupling capacitors (100 nF ceramic) within 1-2 mm of every VDD and VDDA pin; add a 4.7 uF bulk capacitor near the regulator output. For USB applications, the D+/D- pair (PA11/PA12) should be routed as a 90-ohm differential with length matching within 150 mils, kept clear of the HSE crystal traces. The HSE crystal traces (OSC_IN/OSC_OUT) must be short and symmetrically surrounded by a ground guard ring per ST design guidelines.
Power the STM32F105RCT6 from a 3.3V regulator capable of at least 100 mA continuous plus transient peaks (USB host mode draws bursts up to 500 mA on VBUS-side). For RTC backup, route VBAT (pin 6) to a separate low-leakage supply (typically a coin-cell or supercap) so that RTC and backup registers survive VDD loss. Verified by ST reference designs.
Do not swap BOOT0 pin state without checking application note; leaving BOOT0 floating causes random boot mode on power-up. For CAN bit rate above 500 kbit/s, enable the bxCAN advanced settings (single-shot or auto-retransmission off) via firmware; default settings work but engineers often overlook error-passive state handling. Always validate HSE startup time (typically 2-10 ms) before switching to PLL; the HSI fallback is accurate but requires Flash wait-state adjustment.
USB DP/DM traces should be a 90-ohm differential with no stubs and maximum 50 mm length for Full-Speed certification. The Ethernet MAC variant (F107) routes RMII/MII to pins shared with ADC2 and CAN2 on certain board layouts; isolate these analog paths from digital clocks to prevent sampled noise. For SPI buses running above 18 MHz, add 22-33 ohm series resistors near the master to dampen reflections.
اطلاعات انطباق
RoHS and lead-free compliance per ST product page. Halogen-free not explicitly confirmed in retrieved web data. AEC-Q100 automotive qualification not available on -6 industrial grade; check -7 grade or dedicated F105RCT6 automotive parts for auto applications.
