STM8S903K3T3CTR - 16MHz 8-Bit MCU | STMicroelectronics | Embedded Control
MPN: STM8S903K3T3CTR ✓ فعالSTM8S903K3T3CTR نمای کلی
An 8-bit microcontroller is a compact computing device that integrates a processor core, program memory, data memory, and peripherals on one semiconductor die. Within the broader embedded-control hierarchy, the STM8S903K3 belongs to the STM8 access-line family of 8-bit microcontrollers, combining an economical processor architecture with factory-programmable Flash, integrated data EEPROM, and dedicated communication peripherals.
Key features include a maximum 16 MHz clock, 8 Kbytes of Flash, 1 Kbyte of RAM, 640 bytes of true EEPROM, a 10-bit analog-to-digital converter, two timers, UART, SPI, and I²C. The 2.95 V to 5.5 V operating-voltage range supports both 3.3 V and 5 V system designs, while 16 I/O ports provide useful connectivity in a 7 mm by 7 mm LQFP package.
The STM8S903K3/F3 architecture is positioned as a low-density STM8S device, balancing processing capability with low system complexity. Its EEPROM allows frequently changed parameters to be retained in nonvolatile memory, while the ADC and serial interfaces support mixed analog and digital designs. Firmware can use the STM8S microcontroller reference manual RM0016 for register-level programming and peripheral configuration.
Typical applications include compact motor-control modules, industrial sensor nodes, appliance controllers, instrumentation interfaces, low-cost communication equipment, and small consumer products. The combination of 16 I/O ports, three common serial interfaces, and a 10-bit ADC allows the MCU to supervise sensors, operate display or communication peripherals, and manage discrete control functions on a single board.
Designers should verify the 2.95 V minimum supply requirement, provide the decoupling and programming interface specified by the manufacturer, and confirm pin assignments before routing the 32-LQFP footprint. Firmware compatibility, interrupt behavior, and analog accuracy must also be reviewed when changing between STM8S device variants.
This page combines the STM8S903K3 electrical characteristics, same-package family alternatives, interface-focused application guidance, and practical replacement considerations to support component selection, firmware planning, PCB layout, and sourcing decisions.
جایگزینهای drop-in برای STM8S903K3T3CTR — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای STM8S903K3T3CTR (همان فرمفاکتور و فوتپرینت) — متفاوت در Flash Program Memory, Package, Serial Interfaces, I/O Port Count, Data EEPROM.
STM8S103K3T3CTR
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←STM8S003K3T6CTR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←STM8S103K3T6CTR
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←STM8S105K4T6CTR
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←STM8S903K3T3CTR حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | 8-bit microcontroller |
| Product Series | STM8S access line |
| حداکثر فرکانس کلاک | 16 MHz |
| Flash Program Memory | 8 Kbytes (8K x 8) |
| RAM | 1 Kbyte |
| EEPROM | 640 bytes |
| ADC Resolution | 10 bits |
| Timer Count | 2 timers |
| Serial Interfaces | UART, SPI, and I²C |
| I/O Port Count | 16 ports |
| ولتاژ تغذیه کاری | 2.95 V to 5.5 V |
| بستهبندی | 32-pin LQFP (7 mm x 7 mm) |
| نوع نصب | Surface mount |
| Shipping Format | Tape and reel |
| وضعیت چرخه عمر | Active |
| وضعیت RoHS | Compliant |
| Program Memory Type | Flash |
| Core Architecture | 8-bit CISC |
راهنمای پیکربندی پین STM8S903K3T3CTR 32-pin lqfp (7 mm x 7 mm)
پیکربندی پین برای STM8S903K3T3CTR (پکیج 32-pin lqfp (7 mm x 7 mm)). این IC دیجیتال شامل GPIO، رابطهای ارتباطی (UART، SPI، I2C) و پینهای تغذیه است. برای عملکردهای جایگزین پین و گزینههای پیکربندی به دیتاشیت سازنده مراجعه کنید. ضروری برای طراحی سیستمهای نهفته و چیدمان PCB.
داده پینآوت تفصیلی موجود نیست برای STM8S903K3T3CTR.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
STM8S903K3T3CTR مناسب است برای 6 کاربردs: Industrial Sensor Node, Compact Motor Controller, Appliance Control Panel, Communications Interface Module, Portable Measurement Device, LED Lighting Controller.
Industrial Sensor Node
The STM8S903K3T3CTR fits a compact sensor node because its 10-bit ADC can digitize analog inputs while 16 I/O ports handle switches, alarm outputs, and status indicators. The 16 MHz 8-bit processor provides local filtering and control, and the 640-byte EEPROM can retain calibration values or configuration identifiers between power cycles. UART, SPI, and I²C support connection to a transceiver, memory, or upstream controller without requiring a large external peripheral set. The design should verify the ADC input range, reference accuracy, and pin assignment for each analog channel.
پیشنهادی
Compact Motor Controller
The STM8S903K3T3CTR can manage a small motor-control or actuator subsystem using its two timers for timing and PWM-related functions, subject to the exact timer capabilities in the device documentation. Sixteen I/O ports provide control and sensing connections, while the 2.95 V to 5.5 V supply range supports 3.3 V logic systems. The MCU does not replace a dedicated power stage, so motor current, flyback protection, and ground separation must be handled by suitable external circuitry. Firmware should include stall, timeout, and thermal-safety responses.
پیشنهادی
Appliance Control Panel
The STM8S903K3T3CTR is well suited to appliance control panels because it combines 8 Kbytes of Flash, 1 Kbyte of RAM, and EEPROM in one 8-bit device. Its 16 I/O ports can operate buttons, relays, indicators, and discrete sensors, while UART or I²C can connect a display, temperature sensor, or communications module. The 32-pin LQFP package supports compact board layouts. Firmware should define startup states, debounce timing, relay interlocks, and EEPROM write endurance limits appropriate to the product workload.
پیشنهادی
Communications Interface Module
The STM8S903K3T3CTR can serve as the protocol controller in a small communications module using its UART, SPI, or I²C interface. The 16 MHz clock supports interrupt-driven byte and packet processing, while 1 Kbyte of RAM provides working space for short buffers and state machines. Flash stores the protocol firmware, and EEPROM can preserve calibration or addressing information. Interface voltage levels, timing margin, bus loading, and isolation requirements should be checked independently because the MCU operates from 2.95 V to 5.5 V.
پیشنهادی
Portable Measurement Device
The STM8S903K3T3CTR supports portable measurement products where low power, compactness, and mixed-signal control are important. Its 10-bit ADC is suitable for basic process or sensor measurements, while EEPROM retains calibration constants and the 16 I/O ports support controls and indicators. The 2.95 V minimum operating voltage accommodates low-voltage designs, although the complete measurement accuracy depends on the reference circuit, analog front end, sensor, and calibration method. Use the device's low-power modes only after validating wake timing and peripheral state retention.
پیشنهادی
LED Lighting Controller
The STM8S903K3T3CTR can coordinate an LED lighting board where a compact controller needs timers, status outputs, and external communication. Its two timers support timing functions, and 16 I/O ports can drive logic-level control signals, button inputs, or fault indicators. UART, SPI, or I²C can connect a lighting controller, color sensor, or configuration interface. High LED current must remain outside the MCU supply limits, and transistor or MOSFET drivers, current limiting, thermal monitoring, and polarity protection must be implemented separately.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای STM8S903K3T3CTR — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | STM8S103K3T3CTR | STM8S003K3T6CTR | STM8S103K3T6CTR | STM8S105K4T6CTR |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 32-pin LQFP (7 mm x 7 mm) | 32-pin LQFP (7 mm x 7 mm) | 32-pin LQFP (7 mm x 7 mm) | 32-pin LQFP (7 mm x 7 mm) | 32-pin LQFP (7 mm x 7 mm) |
| CPU Architecture | 8-bit | 8-bit | 8-bit | 8-bit | 8-bit |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Flash Program Memory | 8 Kbytes | 8 Kbytes | 8 Kbytes | 8 Kbytes | 16 Kbytes |
| RAM | 1 Kbyte | 1 Kbyte | 1 Kbyte | 1 Kbyte | 1 Kbyte |
تفاوتهای کلیدی
- Documented integration of true EEPROM with mixed-signal and serial peripherals (در مقابلSTM8S003K3T6CTR)
- Close functional match within the STM8S103 family (در مقابلSTM8S103K3T3CTR)
- Same 32-pin footprint with expanded Flash storage (در مقابلSTM8S105K4T6CTR)
یادداشتهای طراحی
Keep the STM8S903K3T3CTR supply inside its 2.95 V to 5.5 V operating range and account for transient margin around clock startup and peripheral activity. Place the manufacturer's recommended decoupling capacitors close to the supply and ground pins, use a short return path, and keep analog and switching-current loops compact. Because the MCU supports both 3.3 V and 5 V systems, verify every connected peripheral's logic levels before using the same board variant.
Assign the 32-LQFP footprint only after checking the complete STM8S903K3 pin-description table, including alternate-function, reset, clock, programming, ground, and supply pins. Maintain the manufacturer-defined clearances and land pattern, and avoid routing high-current switching paths beneath the device. Confirm that the board's exposed assembly constraints accommodate the 7 mm by 7 mm package and its lead pitch before committing to the PCB footprint.
Do not treat another STM8S controller as a drop-in device solely because it uses a 32-pin LQFP package. Check pin multiplexing, ADC channels, timer outputs, UART locations, SPI and I²C pins, clock options, reset behavior, programming signals, memory size, and firmware startup assumptions. A replacement may require a different initialization sequence even when the PCB outline and several headline specifications are the same.
Route SPI, I²C, UART, and ADC signals away from switching nodes and high-current return paths, using continuous ground references beneath the relevant circuitry. For analog measurements, keep the ADC input trace short, isolate it from digital switching activity, and follow the datasheet recommendations for the analog supply and reference arrangement. The 10-bit converter's useful accuracy depends on reference stability and PCB cleanliness as well as the converter itself.
اطلاعات انطباق
RoHS compliance is identified for the STM8S903K3T3CTR. No additional REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification claims are established by the cited product information.