TJA1027TK/20 - 20 kBd LIN Transceiver | NXP Semiconductors
MPN: TJA1027TK/20 ✓ فعالTJA1027TK/20 نمای کلی
A LIN transceiver is a physical-layer interface IC that converts logic-level controller signals into the voltage-based signaling used by a LIN bus, while receiving and conditioning bus signals for the protocol controller. The TJA1027 family is associated with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V vehicle systems. These standards define the electrical behavior, timing, fault handling, and interoperability expectations of LIN vehicle networks.
The TJA1027TK/20 is specifically identified as pin-compatible with the TJA1020 and TJA1021. The cross-reference information also identifies compatibility with the TJA1022, TJA1029, and MC33662 families. This makes the device relevant to designs where an existing LIN transceiver footprint and software architecture must be retained while introducing a LIN 2.x-compatible interface. The 20 kBd operating limit is appropriate for conventional in-vehicle subnetworks rather than high-speed communication links.
The 8-HVSON package supports compact board layouts in automotive electronic control units, body modules, door-control units, and other distributed vehicle systems. The package dimensions, exposed thermal pad, and pin arrangement should be matched to the manufacturer land-pattern and thermal recommendations. The LIN bus wiring also requires correct termination, common-reference handling, and protection appropriate to the vehicle electrical environment.
For practical implementation, follow the pin-description table, recommended external components, bus-loading limits, and application schematic in the NXP TJA1027 datasheet. Pay particular attention to the distinction between the logic-side supply, ground connections, transceiver enable behavior, and LIN bus connection when assigning PCB tracks. Validate the assembled design with the applicable ISO 17987, SAE J2602, and LIN conformance requirements.
This page combines manufacturer protocol and package information with verified sourcing data, engineering selection guidance, drop-in replacement context, and practical PCB and integration considerations for engineers evaluating the TJA1027TK/20 in LIN-based automotive systems.
جایگزینهای drop-in برای TJA1027TK/20 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای TJA1027TK/20 (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Product Type, Maximum Baud Rate, Package Type, Pin Compatibility.
TJA1020T/N1
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TJA1021T/20/C
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TJA1022TK
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TJA1029T/2Z
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MC33662JEF
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TJA1027TK/20 مشخصات
| Product Type | LIN physical-layer transceiver |
| LIN Bus Maximum Baud Rate | 20 kBd |
| Supported LIN Standards | LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A |
| Automotive Standard | SAE J2602 |
| International Standard | ISO 17987-4:2016 (12 V) |
| Bus Compatibility | Pin-compatible with TJA1020 and TJA1021 |
| Additional Pin-Compatible Families | TJA1022, TJA1029, and MC33662 |
| بستهبندی | 8-HVSON (3 x 3 mm) |
| Number of Terminals | 8 |
| نوع نصب | Surface mount |
| Application | In-vehicle sub-networks |
| Transceiver Configuration | Half LIN bus |
راهنمای پیکربندی پین TJA1027TK/20 8-hvson (3 x 3 mm)
پیکربندی پین برای TJA1027TK/20 (پکیج 8-hvson (3 x 3 mm)). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای TJA1027TK/20.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
TJA1027TK/20 مناسب است برای 6 کاربردs: Automotive Body Control Module, Door Control Unit, Automotive Lighting Subnetwork, Vehicle Comfort System, Automotive Sensor Gateway, In-Vehicle Subnetwork Interface.
Automotive Body Control Module
The TJA1027TK/20 is suitable for connecting a body-control module to a conventional LIN subnetwork. Its 20 kBd operating rate and support for LIN 2.0, 2.1, 2.2, 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V systems match the communication requirements of many distributed vehicle functions. Place the transceiver between the vehicle's LIN protocol controller and the bus wiring, then use the manufacturer application circuit for the external bus and protection components. This architecture lets the controller handle protocol timing while the transceiver provides the physical interface. The compact 8-HVSON, 3 x 3 mm package supports dense control-unit layouts, although the exposed-pad land pattern and thermal requirements must be followed exactly.
پیشنهادی
Door Control Unit
A door-control unit can use the TJA1027TK/20 as the physical interface for LIN-connected switches, actuators, sensors, and related subnodes. The device's support for LIN 2.x and SAE J2602 is appropriate for a 12 V vehicle network operating at up to 20 kBd. Keeping the transceiver close to the controller allows the logic-side signals to remain short, while the LIN route is shaped according to the manufacturer's bus recommendations. Verify the transceiver's exact order-code ratings against the vehicle's supply transients, temperature range, and fault-recovery requirements. The 8-HVSON footprint also helps reduce board area in compact electronic control units where connector placement and thermal density are important design constraints.
پیشنهادی
Automotive Lighting Subnetwork
The TJA1027TK/20 can serve as the bus interface for a lighting subnetwork containing distributed lamps, switches, or intelligent lighting controllers. LIN's single-wire bus architecture is well suited to these low-bandwidth vehicle functions, and the TJA1027TK/20 supports the specified LIN 2.x standards at up to 20 kBd. Use the NXP application schematic to implement the bus connection and follow its recommendations for termination, protection, routing, and grounding. Because vehicle lighting systems can experience supply transients and wiring faults, verify the exact device ratings and protection strategy against the platform specification. The small 8-HVSON package helps conserve PCB area in gateway and lighting-control modules without changing the standard LIN controller architecture.
پیشنهادی
Vehicle Comfort System
The TJA1027TK/20 is appropriate for comfort-system subnetworks that connect limited-data nodes such as seat, climate, window, and sensor modules. Its 20 kBd maximum rate is sufficient for the control traffic typically assigned to LIN subnets, while LIN 2.x and SAE J2602 compatibility support standardized automotive behavior. Install the device between the local communication controller and the physical bus, using short logic-side connections and the manufacturer-recommended external network. A common reference between the module and bus is essential for reliable signaling, so follow the grounding and decoupling guidance in the datasheet. The compact 8-HVSON package allows designers to retain the transceiver near the controller when PCB area is constrained.
پیشنهادی
Automotive Sensor Gateway
The TJA1027TK/20 can connect a low-speed sensor gateway to a LIN subnetwork. LIN is commonly used for distributed automotive sensors that exchange modest amounts of diagnostic and control data, and the transceiver's 20 kBd capability is aligned with that role. The protocol controller remains responsible for frame handling, while the TJA1027TK/20 supplies the physical bus interface. Route the LIN connection in accordance with the manufacturer recommendation, account for the bus capacitance and termination arrangement, and provide the specified supply and common-reference implementation. The 3 x 3 mm 8-HVSON package is useful in compact gateways, but engineers should use the exact package drawing to maintain assembly yield and the correct exposed-pad connection.
پیشنهادی
In-Vehicle Subnetwork Interface
The TJA1027TK/20 is designed for the physical interface layer of in-vehicle LIN subnetworks. It supports LIN 2.0, 2.1, 2.2, and 2.2A, together with SAE J2602 and ISO 17987-4:2016 for 12 V systems, making it appropriate for qualified automotive communication designs operating at up to 20 kBd. A successful implementation depends on matching the logic-side controller interface, implementing the prescribed LIN network termination and protection, and validating timing and fault behavior over the vehicle's electrical environment. Because the device is offered in a surface-mount HVSON format, PCB assembly and rework processes should be capable of handling the exposed-pad construction. Confirm the exact order code and qualification before introducing it into a new platform.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای TJA1027TK/20 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | TJA1020 | TJA1021 | TJA1022 | TJA1029 | MC33662 |
|---|---|---|---|---|---|---|
| Package | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Bus Type | LIN | LIN | LIN | LIN | LIN | LIN |
| Pin Compatibility | Compatible with TJA1020 and TJA1021 | Explicitly identified as pin-compatible | Explicitly identified as pin-compatible | Identified as pin-compatible in cross-reference information | Identified as pin-compatible in cross-reference information | Identified as pin-compatible in cross-reference information |
| Application | In-vehicle sub-networks | LIN bus interface | LIN bus interface | LIN bus interface | LIN bus interface | LIN bus interface |
تفاوتهای کلیدی
- Explicit LIN 2.x standard coverage (در مقابلTJA1020)
- Documented compatibility with a broader NXP family set (در مقابلTJA1021)
- Purpose-built 20 kBd automotive LIN interface (در مقابلMC33662)
یادداشتهای طراحی
Implement the logic-side and LIN-side connections using the NXP TJA1027 datasheet application schematic and land pattern. Keep the controller interface traces short, place required decoupling close to the device pins, and route the LIN connection away from sensitive analog or high-speed nets. The 8-HVSON package includes an exposed pad whose connection and solder-process requirements must match the manufacturer drawing.
Preserve a low-impedance common reference between the transceiver, protocol controller, and LIN bus network. Follow the datasheet's termination and external-component arrangement rather than substituting generic values. Check the completed PCB for correct exposed-pad continuity, adequate thermal copper, and clean separation between the sensitive logic interface and the vehicle wiring environment.
Do not substitute a related NXP order code without checking its exact package suffix, electrical limits, temperature grade, qualification, and pin definitions. TJA1027TK/20, TJA1027TK/20/1J, and TJA1027TK/20,118 are distinct commercial identifiers that may differ in packing or regional conditions. Use the manufacturer datasheet to confirm that the candidate uses the required footprint and that every external component remains valid.
Validate the LIN bus with the final wiring length, node count, capacitance, termination, and vehicle transient environment. The 20 kBd maximum rate does not by itself guarantee signal integrity in every installation. Compare measured bus rise time and waveform behavior against the LIN requirements referenced by the TJA1027 datasheet, and retest any change in connectors, harness geometry, or protection components.
اطلاعات انطباق
The manufacturer product information confirms LIN 2.x, SAE J2602, and ISO 17987-4:2016 protocol compliance but does not provide environmental-material declarations in the cited snippet.