TJA1027TK/20 - 20 kBd LIN Transceiver | NXP Semiconductors
MPN: TJA1027TK/20 ✓ Hoạt độngTJA1027TK/20 Tóm tắt
A LIN transceiver is a physical-layer interface IC that converts logic-level controller signals into the voltage-based signaling used by a LIN bus, while receiving and conditioning bus signals for the protocol controller. The TJA1027 family is associated with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V vehicle systems. These standards define the electrical behavior, timing, fault handling, and interoperability expectations of LIN vehicle networks.
The TJA1027TK/20 is specifically identified as pin-compatible with the TJA1020 and TJA1021. The cross-reference information also identifies compatibility with the TJA1022, TJA1029, and MC33662 families. This makes the device relevant to designs where an existing LIN transceiver footprint and software architecture must be retained while introducing a LIN 2.x-compatible interface. The 20 kBd operating limit is appropriate for conventional in-vehicle subnetworks rather than high-speed communication links.
The 8-HVSON package supports compact board layouts in automotive electronic control units, body modules, door-control units, and other distributed vehicle systems. The package dimensions, exposed thermal pad, and pin arrangement should be matched to the manufacturer land-pattern and thermal recommendations. The LIN bus wiring also requires correct termination, common-reference handling, and protection appropriate to the vehicle electrical environment.
For practical implementation, follow the pin-description table, recommended external components, bus-loading limits, and application schematic in the NXP TJA1027 datasheet. Pay particular attention to the distinction between the logic-side supply, ground connections, transceiver enable behavior, and LIN bus connection when assigning PCB tracks. Validate the assembled design with the applicable ISO 17987, SAE J2602, and LIN conformance requirements.
This page combines manufacturer protocol and package information with verified sourcing data, engineering selection guidance, drop-in replacement context, and practical PCB and integration considerations for engineers evaluating the TJA1027TK/20 in LIN-based automotive systems.
Bộ thay thế dễ dàng lắp đặt cho TJA1027TK/20 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TJA1027TK/20 (cùng hình factor và footprint) — khác nhau ở Package, Product Type, Maximum Baud Rate, Package Type, Pin Compatibility.
TJA1020T/N1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TJA1021T/20/C
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TJA1022TK
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TJA1029T/2Z
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC33662JEF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TJA1027TK/20 Thông số kỹ thuật
| Product Type | LIN physical-layer transceiver |
| LIN Bus Maximum Baud Rate | 20 kBd |
| Supported LIN Standards | LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A |
| Automotive Standard | SAE J2602 |
| International Standard | ISO 17987-4:2016 (12 V) |
| Bus Compatibility | Pin-compatible with TJA1020 and TJA1021 |
| Additional Pin-Compatible Families | TJA1022, TJA1029, and MC33662 |
| Hộp | 8-HVSON (3 x 3 mm) |
| Number of Terminals | 8 |
| Kiểu lắp đặt | Surface mount |
| Application | In-vehicle sub-networks |
| Transceiver Configuration | Half LIN bus |
Hướng dẫn cấu hình chân TJA1027TK/20 8-hvson (3 x 3 mm)
Cấu hình chân cho TJA1027TK/20 (8-hvson (3 x 3 mm) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho TJA1027TK/20.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TJA1027TK/20 phù hợp cho 6 Áp dụngs: Automotive Body Control Module, Door Control Unit, Automotive Lighting Subnetwork, Vehicle Comfort System, Automotive Sensor Gateway, In-Vehicle Subnetwork Interface.
Automotive Body Control Module
The TJA1027TK/20 is suitable for connecting a body-control module to a conventional LIN subnetwork. Its 20 kBd operating rate and support for LIN 2.0, 2.1, 2.2, 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V systems match the communication requirements of many distributed vehicle functions. Place the transceiver between the vehicle's LIN protocol controller and the bus wiring, then use the manufacturer application circuit for the external bus and protection components. This architecture lets the controller handle protocol timing while the transceiver provides the physical interface. The compact 8-HVSON, 3 x 3 mm package supports dense control-unit layouts, although the exposed-pad land pattern and thermal requirements must be followed exactly.
Được đề xuất
Door Control Unit
A door-control unit can use the TJA1027TK/20 as the physical interface for LIN-connected switches, actuators, sensors, and related subnodes. The device's support for LIN 2.x and SAE J2602 is appropriate for a 12 V vehicle network operating at up to 20 kBd. Keeping the transceiver close to the controller allows the logic-side signals to remain short, while the LIN route is shaped according to the manufacturer's bus recommendations. Verify the transceiver's exact order-code ratings against the vehicle's supply transients, temperature range, and fault-recovery requirements. The 8-HVSON footprint also helps reduce board area in compact electronic control units where connector placement and thermal density are important design constraints.
Được đề xuất
Automotive Lighting Subnetwork
The TJA1027TK/20 can serve as the bus interface for a lighting subnetwork containing distributed lamps, switches, or intelligent lighting controllers. LIN's single-wire bus architecture is well suited to these low-bandwidth vehicle functions, and the TJA1027TK/20 supports the specified LIN 2.x standards at up to 20 kBd. Use the NXP application schematic to implement the bus connection and follow its recommendations for termination, protection, routing, and grounding. Because vehicle lighting systems can experience supply transients and wiring faults, verify the exact device ratings and protection strategy against the platform specification. The small 8-HVSON package helps conserve PCB area in gateway and lighting-control modules without changing the standard LIN controller architecture.
Được đề xuất
Vehicle Comfort System
The TJA1027TK/20 is appropriate for comfort-system subnetworks that connect limited-data nodes such as seat, climate, window, and sensor modules. Its 20 kBd maximum rate is sufficient for the control traffic typically assigned to LIN subnets, while LIN 2.x and SAE J2602 compatibility support standardized automotive behavior. Install the device between the local communication controller and the physical bus, using short logic-side connections and the manufacturer-recommended external network. A common reference between the module and bus is essential for reliable signaling, so follow the grounding and decoupling guidance in the datasheet. The compact 8-HVSON package allows designers to retain the transceiver near the controller when PCB area is constrained.
Được đề xuất
Automotive Sensor Gateway
The TJA1027TK/20 can connect a low-speed sensor gateway to a LIN subnetwork. LIN is commonly used for distributed automotive sensors that exchange modest amounts of diagnostic and control data, and the transceiver's 20 kBd capability is aligned with that role. The protocol controller remains responsible for frame handling, while the TJA1027TK/20 supplies the physical bus interface. Route the LIN connection in accordance with the manufacturer recommendation, account for the bus capacitance and termination arrangement, and provide the specified supply and common-reference implementation. The 3 x 3 mm 8-HVSON package is useful in compact gateways, but engineers should use the exact package drawing to maintain assembly yield and the correct exposed-pad connection.
Được đề xuất
In-Vehicle Subnetwork Interface
The TJA1027TK/20 is designed for the physical interface layer of in-vehicle LIN subnetworks. It supports LIN 2.0, 2.1, 2.2, and 2.2A, together with SAE J2602 and ISO 17987-4:2016 for 12 V systems, making it appropriate for qualified automotive communication designs operating at up to 20 kBd. A successful implementation depends on matching the logic-side controller interface, implementing the prescribed LIN network termination and protection, and validating timing and fault behavior over the vehicle's electrical environment. Because the device is offered in a surface-mount HVSON format, PCB assembly and rework processes should be capable of handling the exposed-pad construction. Confirm the exact order code and qualification before introducing it into a new platform.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TJA1027TK/20 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TJA1020 | TJA1021 | TJA1022 | TJA1029 | MC33662 |
|---|---|---|---|---|---|---|
| Package | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Bus Type | LIN | LIN | LIN | LIN | LIN | LIN |
| Pin Compatibility | Compatible with TJA1020 and TJA1021 | Explicitly identified as pin-compatible | Explicitly identified as pin-compatible | Identified as pin-compatible in cross-reference information | Identified as pin-compatible in cross-reference information | Identified as pin-compatible in cross-reference information |
| Application | In-vehicle sub-networks | LIN bus interface | LIN bus interface | LIN bus interface | LIN bus interface | LIN bus interface |
Bảo phân biệt quan trọng
- Explicit LIN 2.x standard coverage (vsTJA1020)
- Documented compatibility with a broader NXP family set (vsTJA1021)
- Purpose-built 20 kBd automotive LIN interface (vsMC33662)
Ghi chú thiết kế
Implement the logic-side and LIN-side connections using the NXP TJA1027 datasheet application schematic and land pattern. Keep the controller interface traces short, place required decoupling close to the device pins, and route the LIN connection away from sensitive analog or high-speed nets. The 8-HVSON package includes an exposed pad whose connection and solder-process requirements must match the manufacturer drawing.
Preserve a low-impedance common reference between the transceiver, protocol controller, and LIN bus network. Follow the datasheet's termination and external-component arrangement rather than substituting generic values. Check the completed PCB for correct exposed-pad continuity, adequate thermal copper, and clean separation between the sensitive logic interface and the vehicle wiring environment.
Do not substitute a related NXP order code without checking its exact package suffix, electrical limits, temperature grade, qualification, and pin definitions. TJA1027TK/20, TJA1027TK/20/1J, and TJA1027TK/20,118 are distinct commercial identifiers that may differ in packing or regional conditions. Use the manufacturer datasheet to confirm that the candidate uses the required footprint and that every external component remains valid.
Validate the LIN bus with the final wiring length, node count, capacitance, termination, and vehicle transient environment. The 20 kBd maximum rate does not by itself guarantee signal integrity in every installation. Compare measured bus rise time and waveform behavior against the LIN requirements referenced by the TJA1027 datasheet, and retest any change in connectors, harness geometry, or protection components.
Thông tin tuân thủ
The manufacturer product information confirms LIN 2.x, SAE J2602, and ISO 17987-4:2016 protocol compliance but does not provide environmental-material declarations in the cited snippet.