INA2126U vs INA2126UG4 Comparaison
Comparaison détaillée côte à côte de INA2126U par Texas Instruments et INA2126UG4 par Texas Instruments. Comparez les spécifications clés, les paramètres électriques, le conditionnement, le statut de cycle de vie, les prix et la disponibilité pour déterminer le meilleur composant pour vos exigences de conception.
Texas Instruments
INA2126U - 36V Dual Micropower Instrumentation Amplifier | Texas Instruments
INA2126U ✓ ActifTexas Instruments
INA2126UG4 - 36V Dual Micropower Instrumentation Amplifier | TI
INA2126UG4 ✓ ActifComparaison des spécifications
| Paramètre | INA2126U | INA2126UG4 |
|---|---|---|
| Marque | Texas Instruments | Texas Instruments |
| Catégorie | Amplifier ICs | Amplifier ICs |
| Statut du cycle de vie | Actif | Actif |
| Amplifier Type | Dual precision instrumentation amplifier | — |
| Number of Channels | 2 channels | — |
| Maximum Total Supply Voltage | 36 V | — |
| Operating Supply Range | ±1.35 V to ±18 V | — |
| Minimum Total Supply Voltage | 2.7 V | — |
| Quiescent Current per Channel | 175 µA | — |
| Maximum Input Offset Voltage | 250 µV | — |
| Minimum Voltage Gain | 5 V/V | — |
| Maximum Voltage Gain | 10000 V/V | — |
| Typical Gain-Bandwidth Product | 200 kHz | — |
| Typical Input Noise Density at 1 kHz | 0.4 nV/√Hz | — |
| Internal Architecture | Two-op-amp instrumentation amplifier | — |
| Boîtier | 16-pin SOIC | 16-pin SOIC, 3.90 mm width |
| Type de montage | Surface mount | Surface mount |
| Plage de température de fonctionnement | [DATA_NEEDED: operating temperature range] | [DATA_NEEDED: operating temperature range] |
| Input Bias Current | [DATA_NEEDED: input bias current] | — |
| Common-Mode Rejection Ratio | [DATA_NEEDED: common-mode rejection ratio] | — |
| Slew Rate | [DATA_NEEDED: slew rate] | [DATA_NEEDED: slew rate] |
| Statut RoHS | [DATA_NEEDED: RoHS status] | [DATA_NEEDED: RoHS status] |
| REACH Status | [DATA_NEEDED: REACH status] | [DATA_NEEDED: REACH status] |
| AEC-Q100 Qualification | [DATA_NEEDED: AEC-Q100 qualification] | — |
| Device Type | — | Dual precision instrumentation amplifier |
| Channel Count | — | 2 channels |
| Maximum Supply Voltage | — | 36 V |
| Supply Voltage Range | — | ±1.35 V to ±18 V |
| Single-Supply Minimum | — | 2.7 V |
| Courant de repos | — | 175 µA per channel |
| Offset Voltage | — | 250 µV |
| Architecture | — | Two-op-amp instrumentation-amplifier design |
| Input Type | — | Differential |
| Signal Type | — | Low-level differential-signal acquisition |
| Gain Settings | — | [DATA_NEEDED: available gain settings] |
| Input Common-Mode Range | — | [DATA_NEEDED: input common-mode range] |
| Plage de tension de sortie | — | [DATA_NEEDED: output voltage range] |
| Gain Error | — | [DATA_NEEDED: gain error] |
| Noise Performance | — | [DATA_NEEDED: input noise density] |
| Bandwidth | — | [DATA_NEEDED: signal bandwidth] |