INA2126U vs INA2126UG4 비교
다음의 상세 나란히 비교: INA2126U 제조: Texas Instruments 및 INA2126UG4 제조: Texas Instruments. 주요 사양, 전기적 파라미터, 패키징, 수명 주기 상태, 가격 및 재고를 비교하여 설계 요구 사항에 가장 적합한 부품을 결정하십시오.
Texas Instruments
INA2126U - 36V Dual Micropower Instrumentation Amplifier | Texas Instruments
INA2126U ✓ 활성사양 비교
| 파라미터 | INA2126U | INA2126UG4 |
|---|---|---|
| 브랜드 | Texas Instruments | Texas Instruments |
| 카테고리 | Amplifier ICs | Amplifier ICs |
| 수명 주기 상태 | 활성 | 활성 |
| Amplifier Type | Dual precision instrumentation amplifier | — |
| Number of Channels | 2 channels | — |
| Maximum Total Supply Voltage | 36 V | — |
| Operating Supply Range | ±1.35 V to ±18 V | — |
| Minimum Total Supply Voltage | 2.7 V | — |
| Quiescent Current per Channel | 175 µA | — |
| Maximum Input Offset Voltage | 250 µV | — |
| Minimum Voltage Gain | 5 V/V | — |
| Maximum Voltage Gain | 10000 V/V | — |
| Typical Gain-Bandwidth Product | 200 kHz | — |
| Typical Input Noise Density at 1 kHz | 0.4 nV/√Hz | — |
| Internal Architecture | Two-op-amp instrumentation amplifier | — |
| 패키지 | 16-pin SOIC | 16-pin SOIC, 3.90 mm width |
| 실장 유형 | Surface mount | Surface mount |
| 동작 온도 범위 | [DATA_NEEDED: operating temperature range] | [DATA_NEEDED: operating temperature range] |
| Input Bias Current | [DATA_NEEDED: input bias current] | — |
| Common-Mode Rejection Ratio | [DATA_NEEDED: common-mode rejection ratio] | — |
| Slew Rate | [DATA_NEEDED: slew rate] | [DATA_NEEDED: slew rate] |
| RoHS 상태 | [DATA_NEEDED: RoHS status] | [DATA_NEEDED: RoHS status] |
| REACH Status | [DATA_NEEDED: REACH status] | [DATA_NEEDED: REACH status] |
| AEC-Q100 Qualification | [DATA_NEEDED: AEC-Q100 qualification] | — |
| Device Type | — | Dual precision instrumentation amplifier |
| Channel Count | — | 2 channels |
| Maximum Supply Voltage | — | 36 V |
| Supply Voltage Range | — | ±1.35 V to ±18 V |
| Single-Supply Minimum | — | 2.7 V |
| 대기 전류 | — | 175 µA per channel |
| Offset Voltage | — | 250 µV |
| Architecture | — | Two-op-amp instrumentation-amplifier design |
| Input Type | — | Differential |
| Signal Type | — | Low-level differential-signal acquisition |
| Gain Settings | — | [DATA_NEEDED: available gain settings] |
| Input Common-Mode Range | — | [DATA_NEEDED: input common-mode range] |
| 출력 전압 범위 | — | [DATA_NEEDED: output voltage range] |
| Gain Error | — | [DATA_NEEDED: gain error] |
| Noise Performance | — | [DATA_NEEDED: input noise density] |
| Bandwidth | — | [DATA_NEEDED: signal bandwidth] |