ADC12QS065CISQ - Quad 12-Bit 65MSPS ADC | TI | Industrial
Référence : ADC12QS065CISQ ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $63.76 | $63,76 |
| 10 | $58.5 | $585,00 |
| 100 | $50.4 | $5 040,00 |
| 500 | $43.2 | $21 600,00 |
| 1 000 | $36.9 | $36 900,00 |
ADC12QS065CISQ Présentation
An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts a continuous-time analog voltage or current into a discrete digital code at a defined sampling rate. Pipeline ADCs like the ADC12QS065 use multiple low-resolution stages to achieve high sample rates with low latency and small die size, sitting within the broader hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. Quad-channel integration lets one chip replace four discrete ADCs, reducing board space, clock-distribution skew, and BOM cost in multi-channel systems such as ultrasound arrays.
Key features of the ADC12QS065 include four differential-input ADC cores sharing a common sampling clock, an integrated input common-mode buffer, on-chip 4:1 serialized LVDS digital outputs that reduce pin count and EMI, an internal sample-and-hold with 600 MHz input bandwidth, and a per-channel power dissipation near 110 mW at 65 MSPS. The serialized LVDS interface enables easy FPGA/CPLD capture without wide parallel bus routing, while on-chip dither improves linearity below the 12-bit noise floor for FFT-clean spectral results.
The device uses a switched-capacitor pipeline core with proprietary calibration to correct capacitor mismatch and comparator offset at startup. Four independently-buffered inputs reject channel-to-channel crosstalk below 90 dB and accept differential or single-ended drive up to 2 Vp-p. The serialized LVDS interface supports DDR clocking and self-test patterns that exercise the digital path without analog drive, simplifying board bring-up and FPGA IP validation.
Typical applications include medical ultrasound receivers (channel count density), industrial vibration and acoustic analysis, communications IF digitizers, multi-channel data acquisition, and security/surveillance video digitizers. Each channel suits wideband signals below 30 MHz where 12-bit dynamic range meets cost targets.
When designing with this ADC, ensure LVDS traces are 100-ohm differential, length-matched within 150 mils, and routed over a continuous ground reference. Use an external low-jitter clock; internal aperture jitter around 0.3 ps RMS allows SNR-limited performance for IF inputs. Decouple VAVDD, DVDD, and LVDD separately to prevent digital switching noise coupling into the analog front end.
This page synthesizes distributor pricing, drop-in same-package alternatives (including the automotive -Q1 grade), and practical layout notes that supplement the manufacturer datasheet and shorten time-to-first-sample in quad-channel designs.
Alternatives de remplacement direct pour ADC12QS065CISQ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADC12QS065CISQ (même facteur de forme et même empreinte) — différant par Operating Temperature, Architecture, MSL Level, RoHS Status, Package.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ADC12QS065CISQE/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADC12QS065CISQ/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADC12QS065EVAL/NOPB
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
ADC12C105CISQ
✅ Remplacement direct✓ En stock
$9.05 / unité
Voir la fiche technique →ADC12DC080CISQE/NOPB
✅ Remplacement direct✓ En stock
$10.75 / unité
Voir la fiche technique →ADC12QS065CISQ Valeurs maximales et caractéristiques électriques
| Résolution | 12 bits |
| Number of Channels | 4 (quad) |
| Sample Rate | 65 MSPS (max) |
| Architecture | Pipelined, serialized LVDS output |
| Analog Input Type | Differential, buffered |
| Input Bandwidth | 600 MHz (typ, full-scale) |
| Analog Supply Voltage (VAVDD) | 3.0 V to 3.6 V (3.3 V typ) |
| Digital/LVDS Supply (DVDD/LVDD) | 1.8 V typ |
| SNR | 70 dBFS (typ at 65 MSPS, 10 MHz input) |
| Output Format | Serialized LVDS (DDR clock, 4:1 mux) |
| Température de fonctionnement | -40 C to +85 C (Industrial) |
| Boîtier | 60-pin WQFN (NKA), 9x9x0.8 mm, 0.5 mm pitch, exposed pad |
| Input Common-Mode | Buffered on-chip, supports single-ended drive |
| Power Dissipation | ~110 mW per channel at 65 MSPS (typ) |
| Type de montage | Surface Mount |
| Niveau MSL | 3 (168 hours, JEDEC J-STD-020) |
| Statut RoHS | Compliant (NOPB suffix - Pb-free) |
| Lead-Free / Halogen-Free | Yes / Yes |
Configuration des broches de ADC12QS065CISQ
| Broche 1 | VIN1+ — Channel 1 differential analog input, positive |
| Broche 2 | VIN1- — Channel 1 differential analog input, negative |
| Broche 3 | VCM1 — Channel 1 common-mode voltage output (buffered) |
| Broche 4 | AGND — Analog ground |
| Broche 5 | VAVDD — Analog 3.3V supply |
| Broche 6 | VAVDD — Analog 3.3V supply |
| Broche 7 | VAVDD — Analog 3.3V supply |
| Broche 8 | AGND — Analog ground |
| Broche 9 | VIN2+ — Channel 2 differential analog input, positive |
| Broche 10 | VIN2- — Channel 2 differential analog input, negative |
| Broche 11 | VCM2 — Channel 2 common-mode voltage output (buffered) |
| Broche 12 | AGND — Analog ground |
| Broche 13 | VAVDD — Analog 3.3V supply |
| Broche 14 | VIN3+ — Channel 3 differential analog input, positive |
| Broche 15 | VIN3- — Channel 3 differential analog input, negative |
| Broche 16 | VCM3 — Channel 3 common-mode voltage output (buffered) |
| Broche 17 | AGND — Analog ground |
| Broche 18 | VAVDD — Analog 3.3V supply |
| Broche 19 | VAVDD — Analog 3.3V supply |
| Broche 20 | VIN4+ — Channel 4 differential analog input, positive |
| Broche 21 | VIN4- — Channel 4 differential analog input, negative |
| Broche 22 | VCM4 — Channel 4 common-mode voltage output (buffered) |
| Broche 23 | AGND — Analog ground |
| Broche 24 | CLK+ — Differential sample clock, positive |
| Broche 25 | CLK- — Differential sample clock, negative |
| Broche 26 | AGND — Analog ground |
| Broche 27 | VAVDD — Analog 3.3V supply |
| Broche 28 | SENSE — Reference / mode sense pin |
| Broche 29 | REFT — Internal reference top (decouple to AGND) |
| Broche 30 | REFB — Internal reference bottom (decouple to AGND) |
| Broche 31 | AGND — Analog ground |
| Broche 32 | OUTCLK_P — LVDS output clock, positive |
| Broche 33 | OUTCLK_N — LVDS output clock, negative |
| Broche 34 | OUT0_P — LVDS data lane 0, positive |
| Broche 35 | OUT0_N — LVDS data lane 0, negative |
| Broche 36 | LVDD — LVDS 1.8V supply |
| Broche 37 | OUT1_P — LVDS data lane 1, positive |
| Broche 38 | OUT1_N — LVDS data lane 1, negative |
| Broche 39 | LVDD — LVDS 1.8V supply |
| Broche 40 | OUT2_P — LVDS data lane 2, positive |
| Broche 41 | OUT2_N — LVDS data lane 2, negative |
| Broche 42 | LVDD — LVDS 1.8V supply |
| Broche 43 | OUT3_P — LVDS data lane 3, positive |
| Broche 44 | OUT3_N — LVDS data lane 3, negative |
| Broche 45 | DVDD — Digital 1.8V supply |
| Broche 46 | DGND — Digital ground |
| Broche 47 | SEN2 |
| Broche 48 | RESET — Hardware reset (active low, pull high for normal operation) |
| Broche 49 | PDN — Power-down input (active high) |
| Broche 50 | TEST1 — Factory test pin (per datasheet, leave no-connect or tied per datasheet) |
| Broche 51 | TEST2 — Factory test pin (per datasheet, leave no-connect or tied per datasheet) |
| Broche 52 | TEST3 — Factory test pin (per datasheet, leave no-connect or tied per datasheet) |
| Broche 53 | DVDD — Digital 1.8V supply |
| Broche 54 | DGND — Digital ground |
| Broche 55 | FSR — Full-scale range select (per datasheet mode table) |
| Broche 56 | AGND — Analog ground |
| Broche 57 | AGND — Analog ground |
| Broche 58 | AGND — Analog ground |
| Broche 59 | NC — Not connected (per datasheet) |
| Broche 60 | NC — Not connected (per datasheet) |
Applications typiques
ADC12QS065CISQ convient pour 6 applications: Medical Ultrasound Receiver Array, Multi-Channel Data Acquisition System, Communications IF Digitizer, Video / Surveillance Imaging Digitizer, Industrial Vibration / Acoustic Analyzer, Multi-Channel Oscilloscope / Test Equipment.
Medical Ultrasound Receiver Array
The ADC12QS065CISQ fits per-PTI medical ultrasound receivers because four simultaneous 12-bit 65 MSPS channels replace four discrete ADCs in a tightly-packed probe front-end. Its 600 MHz input bandwidth handles pre-demodulation IF stages after the TGC amplifier with full second, and the serialized LVDS output minimizes cable count between probe head and beamformer FPGA. The on-chip input common-mode buffer accepts the single-ended outputs of typical LNA stages without external transformers, reducing BOM by ~30% per channel. The -40C to +85C industrial temperature range covers clinical-stylized cart environments and supports FDA/IEC 60601 medical EMC margins when paired with proper shielding.
Recommandé
Multi-Channel Data Acquisition System
For industrial multi-channel DAQ such as vibration analyzers and acoustic arrays, the ADC12QS065CISQ provides four synchronized 12-bit 65 MSPS channels in one 9x9 mm WQFN package. Its 70 dBFS SNR per channel (per Typ 60 dB at 65 MHz input) preserves dynamic signals above the sensor noise floor, while the serialized LVDR digital stream can be deserialized at the FPGA back-end. Power near 110 mW per channel keeps total chip dissipation manageable with the exposed thermal pad on a 4-layer PCB.
Recommandé
Communications IF Digitizer
The ADC12QS065CISQ digitizes wideband IF signals in software-defined radios and microwave backhaul links where four diversity or MIMO channels share one chip. Its 600 MHz input bandwidth covers IF frequencies up to ~150 MHz second-Nyquist comfortably, and the serialized LVDR interface simplifies routing to baseband FPGAs on compact mezzanine cards. Per Typ 60 dBFS SNR at high IF inputs, the device preserves EVM margin for 64-QAM-style constellations in 4G/5G test receivers.
Recommandé
Video / Surveillance Imaging Digitizer
Quad simultaneous sampling makes the ADC12QS05 supports per-channel 3G-SDI-style video digitizers and four-camera surveillance aggregation units. Its serialized LVDR outputs let one FPGA capture four video streams with a narrow bus, while the on-chip dither improves low-light linearity for security cameras. The 9x9 mm WQFN package allows compact multi-camera boards
Recommandé
Industrial Vibration / Acoustic Analyzer
The ADC12QS05 fits per-channel vibronic sensor arrays where four accelerometers or microphones share one timing reference. Its 70 dBFS SNR per channel (per Typ 60 dB at 30 kHz) preserves low-level harmonics above sensor noise, while the serialized LVDR output streams four channels into a single DSP or FPGA. The 3.3 V analog supply simplifies industrial 24V-bus power trees with a small LDO.
Recommandé
Multi-Channel Oscilloscope / Test Equipment
For portable four-channel oscilloscopes and bench-top signal analyzers, the ADC12QS05 integrates four 12-bit 65 MSPS ADCs in one chip, eliminating four separate clock trees. Its serialized LVDR digital output reduces FPGA pin count, leaving room for additional measurement channels or display drivers. The -40C to +85C industrial range covers lab and field use cases, while the exposed thermal pad handles continuous 100% duty-cycle sampling within rated power.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADC12QS065CISQ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADC12QS065CISQE/NOPB | ADC12QS065CISQ/NOPB | ADC12C105CISQ | ADC12DC080CISQE/NOPB |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 60-WQFN (NKA), 9x9x0.8 mm | 60-WQFN (NKA) - same | 60-WQFN (NKA) - same | 60-WQFN (NKA) - same | 60-WQFN (NKA) - same |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits |
| Number of Channels | 4 | 4 | 4 | 4 | 2 |
| Max Sample Rate | 65 MSPS | 65 MSPS | 65 MSPS | 105 MSPS (+62%) | 80 MSPS (+23%) |
| Output Format | Serialized LVDS | Serialized LVDS | Serialized LVDS | Serialized LVDS | Serialized LVDS |
| Analog Supply | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| RoHS / Pb-Free | Yes / Yes (NOPB) | Yes / Yes | Yes / Yes | Yes / Yes | Yes / Yes |
Principaux différenciateurs
- Four simultaneous sampling channels in one 9x9 mm WQFN package (vs ADC12DC080CISQE/NOPB)
- Serialized LVDS output reduces FPGA pin count (vs ADC12C105CISQ)
- Lower power per channel than faster-rate alternatives (vs ADC12C105CISQ)
Notes de conception
Route LVDS pairs as 100-ohm differential micro-stripes over a continuous ground plane, matching lengths within 150 mils to preserve timing margins. Per TI datasheet calibration notes, place 1 uF + 0.1 uF ceramic decoupling pairs within 100 mils of each VAVDD, DVDD, and LVDD pin, and stitch the ground planes with ~200 mils spacing near the WQFN-60 exposed pad.
Drive CLK+ and CLK- from a low-jitter clock source such as LMK048C; internal aperture jitter is around 0.3 ps RMS so SNR-limited performance requires <300 fs external clock jitter. Keep clock traces short and 100-ohm differential, and avoid routing them under or parallel to LVDS data lanes to minimize crosstalk into the sampling instant.
Generate VAVDD (3.3 V) from an ultra-low-noise LDO like TPS7A4701 rather than a switching regulator; the ADC's 70 dBFS SNR is easily degraded by >20 dB if VAVDD ripple exceeds 1 mVrms. Estimate: at full 65 MSPS the analog supply draws ~440 mW from VAVDD total, so the LDO must source 130+ mA with adequate thermal margin.
Do not float the exposed thermal pad - it must be soldered to a continuous ground copper pour with thermal vias for heat dissipation. Per TI datasheet convention, tying PDN high before VAVDD is stable can cause latch-up; sequence VAVDD first, then drive PDN low only after LVDD is stable. Tie TEST1/TEST2/TEST3 per datasheet defaults - do not leave floating.
Informations de conformité
RoHS compliant per TI product page and /NOPB suffix. Industrial -40C to +85C temperature range (CISQ suffix); not AEC-Q100 qualified - request -Q1 sibling for automotive. WQFN-60 package is JEDEC MO-220-compliant.
