Texas Instruments

LM258PG4 - Dual 30V 700kHz Op Amp | Texas Instruments

Référence : LM258PG4 ✓ Actif
30 V Vdss 500 µA per channel Id 8-pin PDIP Package Internally compensated Speed
MOQ : 1 |

LM258PG4 Présentation

The Texas Instruments LM258PG4 is a dual, general-purpose operational amplifier with a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and 0.3 V/µs slew rate, housed in an 8-pin PDIP package. The two amplifiers are designed for instrumentation, signal-conditioning, and control applications operating from single or dual supplies.

An operational amplifier is a high-gain analog building block used to amplify, buffer, filter, compare, or drive external signals. The LM258 belongs to the dual-operational-amplifier hierarchy within the broader categories of analog IC, amplifier IC, and semiconductor. Its internally compensated architecture simplifies design by eliminating the need for an external compensation network in typical closed-loop configurations.

The principal performance features include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and approximately 500 µA quiescent current per channel. These ratings make the device suitable for general-purpose voltage amplification, current-to-voltage conversion, active filtering, transducers, and industrial control loops. Its 30 V supply rating also provides additional headroom for industrial systems operating from higher-voltage rails than conventional low-voltage mixed-signal circuits.

Each channel contains an input differential pair, voltage-amplification stage, output stage, and internal frequency compensation. Because the amplifiers are independent, they can amplify two separate signals or be configured as one differential amplifier plus one additional signal channel. The 700 kHz bandwidth supports general-purpose closed-loop operation rather than the much wider bandwidth associated with precision, high-speed, or FET-input amplifier families.

Typical uses include sensor-interface amplification, industrial instrumentation, audio preamplification, active filters, relay and solenoid-driver stages, and low-frequency control systems. The dual configuration can reduce board area when two analog channels are required, while through-hole PDIP construction can simplify prototyping, inspection, and manual assembly.

Designers should verify input common-mode range, output swing, input bias current, offset voltage, noise, and output-current limits against the manufacturer datasheet for the selected operating point. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet rather than left open.

This product page combines the LM258PG4 family specifications, ordering information, package details, and practical selection guidance with same-footprint alternatives. It is intended to help engineers move from circuit requirements to a defensible dual-op-amp selection without relying on generic amplifier-family descriptions.

Alternatives de remplacement direct pour LM258PG4 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec LM258PG4 (même facteur de forme et même empreinte) — différant par Mounting Type, Package, Slew Rate, Amplifier Type, Frequency Compensation.

Texas Instruments
Package: 8-PDIP
Comparer avec LM258PG4 →
Texas Instruments
Frequency Compensation: Internally frequency compensated
Comparer avec LM258PG4 →
Texas Instruments
Mounting Type: Through Hole
Slew Rate: 13 V/µs (typical)
Amplifier Type: JFET-Input Operational Amplifier
Comparer avec LM258PG4 →

LM2904P

✅ Remplacement direct ⚠️ Spécifications non vérifiées
Texas Instruments
📦 8-pin PDIP
Dual operational amplifier · 2 · 26 V · 700 kHz · 8-PDIP · Through-hole · Standard general-purpose amplifier

Contactez-nous pour le prix

Voir la fiche technique →

LM358P

✅ Remplacement direct ⚠️ Spécifications non vérifiées
Texas Instruments
📦 8-pin PDIP
Dual operational amplifier · 2 circuits · 2 independent operational amplifiers · 3 V to 32 V · Single supply · 700 kHz · 0.3 V/µs · Internally frequency compensated

Contactez-nous pour le prix

Voir la fiche technique →

TL072CP

✅ Remplacement direct
Texas Instruments
📦 8-pin PDIP
Texas Instruments · Active · JFET-Input Operational Amplifier · 2 (Dual) · 13 V/µs (typical) · 3 MHz (typical) · 30 pA (typical) · 3 mV (typical, C grade)

Contactez-nous pour le prix

Voir la fiche technique →

LM258PG4 Valeurs maximales et caractéristiques électriques

Amplifier Type General-purpose dual operational amplifier
Number of Channels 2 channels
Maximum Supply Voltage 30 V
Single-Supply Operating Range 3 V to 32 V
Plage de température de fonctionnement -25°C to +85°C
Gain-Bandwidth Product 700 kHz
Slew Rate 0.3 V/µs
Courant de repos 500 µA per channel
Frequency Compensation Internally compensated
Boîtier 8-pin PDIP
Type de montage Through-hole
Operating Voltage 3 V to 32 V

Guide de configuration des broches du LM258PG4 8-pin pdip

Configuration des broches du LM258PG4 (boîtier 8-pin pdip). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.

Schéma de brochage du boîtier 8-pin pdip pour le LM258PG4

Aucune donnée de brochage détaillée disponible pour LM258PG4.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

LM258PG4 convient pour 6 applications: Industrial Sensor Signal Conditioning, Active Audio Preamplifier, Active Filter and Tone Control, Current-to-Voltage Measurement, Relay and Solenoid Driver Interface, General-Purpose Control Loop.

🏭

Industrial Sensor Signal Conditioning

The LM258PG4 fits low-frequency industrial sensor interfaces that require two analog channels, a supply span of 3 V to 32 V, and operation from -25°C to 85°C. Each internally compensated channel can amplify a sensor voltage, buffer it for an ADC, or form an active filter without an external compensation network. Its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate provide useful bandwidth for common pressure, temperature, and position sensors. Designers should still verify the input common-mode range, output swing, offset voltage, and bias-current requirements for the selected sensor and excitation level.

🎧

Active Audio Preamplifier

The LM258PG4 can provide two independent general-purpose audio preamplifier stages for mixer, monitoring, or line-level signal conditioning. A 700 kHz gain-bandwidth product covers the audible range with margin, while the 0.3 V/µs slew rate helps reproduce moderate-amplitude transients. The dual 8-pin PDIP package simplifies through-hole construction and allows one amplifier to serve the left channel while the other serves the right. For high-fidelity systems, verify input noise, output drive, distortion, and output-voltage swing against the manufacturer electrical characteristics.

🎛️

Active Filter and Tone Control

The LM258PG4 is suitable for first-order or moderate-Q active-filter stages and tone-control networks because it combines internal frequency compensation with a 700 kHz gain-bandwidth product. A pair of amplifiers can implement a two-pole signal path or a dual-section filter, provided component tolerances and loop-gain requirements are considered. The 3 V to 32 V operating span supports both conventional ±15 V laboratory rails and lower single-supply systems after the signal and output ranges have been checked. The 0.3 V/µs slew rate should remain adequate for the intended bandwidth and signal amplitude.

📡

Current-to-Voltage Measurement

The LM258PG4 can implement a transimpedance stage for low-frequency current measurements when the sensor current and feedback impedance produce acceptable operating voltage and bandwidth requirements. One channel performs current-to-voltage conversion, while the second channel can provide gain, offset correction, or active filtering. Its two-channel architecture reduces external amplification in instrumentation designs, and its internally compensated construction simplifies the feedback network. Confirm input bias current, input offset voltage, common-mode range, output swing, and stable feedback resistance before selecting the resistor values.

⚡

Relay and Solenoid Driver Interface

The LM258PG4 can provide the voltage gain needed between a low-level control signal and the input stage of a relay, solenoid, or indicator driver. Its 30 V maximum supply rating and 3 V to 32 V operating span suit higher-voltage industrial interfaces better than amplifiers limited to low supply rails. The two channels can control separate loads when each output stage operates within its voltage and current limits. Confirm output swing, output-current capability, load transients, and any flyback protection requirements; the operational amplifier itself may require an external driver transistor.

🔧

General-Purpose Control Loop

The LM258PG4 is suitable for proportional, integral, or general feedback-control prototypes where the loop bandwidth remains well below the 700 kHz device bandwidth. A single channel can implement the error amplifier while the second handles an auxiliary signal, monitor, or reference buffer. Its -25°C to 85°C operating range covers many industrial and commercial environments, and the internally compensated topology simplifies initial control-loop design. Verify loop stability, output swing, slew-rate margin, load behavior, and supply-noise performance before committing the amplifier to a compensation scheme.

What is the LM258PG4?
The LM258PG4 is a Texas Instruments dual, general-purpose operational amplifier in an 8-pin PDIP package. According to the TI LM258 product page, it supports a maximum 30 V supply, a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and operation from -25°C to 85°C. Its two internally compensated channels suit independent signal-amplification, buffering, filtering, and industrial control functions.
What are the key specifications of LM258PG4 that engineers should know?
The LM258PG4 provides two internally compensated op-amp channels, a 700 kHz gain-bandwidth product, a 0.3 V/µs slew rate, approximately 500 µA of quiescent current per channel, and operation over a 3 V to 32 V supply span. The TI LM258 product page also identifies a 30 V maximum supply rating and a -25°C to 85°C temperature range. Its 8-pin PDIP package is suitable for through-hole assembly and prototyping.
Where can I download the LM258PG4 datasheet PDF?
The official LM258 documentation starts at the Texas Instruments product page, where ordering information, technical parameters, support material, and the linked datasheet are presented together. Use the manufacturer LM258 datasheet for the definitive pin descriptions, recommended operating conditions, electrical characteristics, and application guidance. The product page is available at https://www.ti.com/product/LM258.
Where can I find the LM258PG4 pinout?
Use the pin-description table and package drawing in the Texas Instruments LM258 datasheet to identify the two amplifier inputs, outputs, supply pins, and any no-connect positions on the 8-pin PDIP. The LM258PG4 is an 8-pin PDIP device, but individual signal names are assigned according to the manufacturer numbering convention. Confirm the package drawing before assigning PCB tracks or prototyping a replacement board.
Can LM258PG4 operate from a single supply?
Yes, the LM258PG4 can operate from a single supply within the stated 3 V to 32 V span. According to the TI LM258 product information, the device is designed for single-supply operation as well as conventional dual-supply configurations. Input common-mode and output-swing limits still apply, so the selected rail must keep both channels inside the datasheet operating region.
Is LM258PG4 suitable for industrial instrumentation?
The LM258PG4 is suitable for many industrial instrumentation tasks because it combines two channels, a 3 V to 32 V supply span, and a -25°C to 85°C operating range. According to the TI product page, its 700 kHz bandwidth and 0.3 V/µs slew rate are appropriate for general-purpose low-frequency measurement and control circuits. Precision requirements should be checked against offset, bias-current, and noise specifications.
What can replace LM258PG4?
LM2904P is the closest temperature-oriented option for industrial circuits, while LM358P offers a lower-power dual-amplifier choice. TL072CP can fit some 8-pin dual-op-amp layouts but has a materially lower maximum supply rating. These are not unconditional replacements: verify the pin arrangement, input common-mode range, output swing, supply limits, temperature grade, bandwidth, and load capability against the original design.
Is LM358P the same as LM258PG4?
No, LM358P and LM258PG4 are related dual operational amplifiers, but they are not electrically identical. The LM258 family is identified with a 30 V maximum supply and a -25°C to 85°C operating range, while LM358-family specifications and temperature grades differ. Their 8-pin PDIP formats may permit layout reuse, but circuit selection still requires checking supply voltage, input range, output swing, and load current.
LM258PG4 vs LM2904P: which is better for industrial control?
Choose LM2904P when the application requires the wider industrial temperature range associated with the LM2904 family. Choose LM258PG4 when its stated -25°C to 85°C range covers the expected ambient conditions and the 30 V maximum supply rating matches the design. According to the TI LM258 family documentation, both families are based on dual high-gain, internally compensated operational-amplifier architectures.
When should I choose LM258PG4 over LM358P?
Choose LM258PG4 when the circuit benefits from its defined 30 V maximum supply rating and -25°C to 85°C operating range. Choose LM358P when lower quiescent current is more important and the lower supply-voltage envelope, temperature grade, and electrical limits remain acceptable. Confirm every operating point against the manufacturer datasheet rather than treating the shared PDIP footprint as proof of equivalent performance.
Is LM258PG4 suitable for sensor signal conditioning?
Yes, the LM258PG4 can be used for general-purpose sensor signal conditioning when the sensor bandwidth and source impedance do not exceed the amplifier's capabilities. Its 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and two-channel architecture suit buffering, gain adjustment, and active filtering. Sensor-specific accuracy depends on input bias current, offset voltage, noise, and common-mode range.
What is the best TI equivalent for LM258PG4?
The best TI alternative depends on the design priority. LM2904P is appropriate when a broader industrial temperature range is needed, while LM358P may be preferable when lower quiescent current is valuable. LM258N belongs to the same family but may have a different commercial temperature grade. Use the exact ordering table and datasheet to confirm electrical and environmental equivalence before substitution.
What is the best NXP equivalent for LM258PG4?
An NXP equivalent cannot be selected reliably from a generic cross-reference result. The NXP LM258 documentation describes the related 532, 358, and LM2904 operational-amplifier families, but the exact ordering suffix determines package, temperature grade, and lifecycle status. Compare the NXP pinout and electrical characteristics with the LM258PG4 and confirm the exact MPN before treating it as a drop-in replacement.
Where can I buy LM258PG4 online?
Use the Request a Quote form on this page to request LM258PG4 pricing, availability, lead time, and order handling from XAIPART. The exact commercial terms can vary with quantity, package quantity, and current inventory. The manufacturer product page at https://www.ti.com/product/LM258 provides the authoritative ordering table and lifecycle information for the LM258 family.
What is the price of LM258PG4?
The current unit price and volume tiers for LM258PG4 are presented through the Request a Quote form on this page. Pricing can vary with order quantity, supplier inventory, and fulfillment requirements, so an account-specific quotation is more useful than a static price table. Request the quantity needed for your production build to obtain current commercial terms.
What is the lead time for LM258PG4 and is it in stock?
Request the current LM258PG4 lead time, minimum order quantity, and stock status through the Request a Quote form on this page. The Texas Instruments product page provides the authoritative product and ordering status, while fulfillment timing can change with inventory and order configuration. Use the quotation response for a current, application-specific commitment.

Données de référence d'ingénierie pour LM258PG4 — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose LM258PG4 for general-purpose dual-op-amp designs that operate from a 3 V to 32 V supply span, require approximately 500 µA per channel, and remain within -25°C to 85°C. It is particularly useful when two independent amplifiers are needed for sensor conditioning, audio preamplification, filtering, or control loops. Choose LM2904P when the circuit needs a wider industrial temperature range and the exact electrical characteristics remain acceptable. Choose LM358P when lower quiescent current is the priority and its supply, temperature, input-range, and output-swing limits fit the application. TL072CP can suit a design needing JFET inputs or higher bandwidth, but its lower supply limit prevents straightforward substitution into 30 V-class circuits. For every alternative, validate the exact pinout, common-mode range, output swing, load current, stability, and lifecycle requirements before releasing production artwork.

Comparaison avec les alternatives

Paramètre Ce produit LM2904P LM358P TL072CP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin PDIP 8-pin PDIP - same 8-pin PDIP - same 8-pin PDIP - same
Number of Channels 2 channels 2 channels 2 channels 2 channels

Principaux différenciateurs

  • Defined 30 V maximum supply rating (vs TL072CP)
  • General-purpose dual internal compensation (vs TL072CP)
  • Defined -25°C to +85°C operating range (vs LM358P)
  • Two independent channels in one PDIP (vs LM2904P)

Notes de conception

Place the supply-decoupling network close to the LM258PG4 pins, with a short ground return to limit loop area. The device operates from 3 V to 32 V, but maximum supply voltage and total power dissipation must both be respected in high-voltage circuits. If the source rail can exceed 30 V during fault conditions, add appropriate protection rather than relying on normal operating tolerance.

Route each feedback path directly between the amplifier output and its inverting input, and keep input and output traces physically separated where practical. Maintain a continuous ground reference around the PDIP footprint and avoid long exposed traces that can couple adjacent-channel signals. Because the two channels share a package and supply pins, asymmetric or high-gain layouts can increase crosstalk and oscillation risk.

Do not assume that a shared 8-pin PDIP footprint guarantees drop-in equivalence. LM2904P, LM358P, and TL072CP differ in temperature grade, supply capability, input stage, bandwidth, or current behavior. Verify the exact pin mapping, input common-mode range, output swing, quiescent current, load capability, and stability requirements before modifying an existing LM258PG4 board.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The LM258 family is presented by the manufacturer as a general-purpose dual operational amplifier, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements for LM258PG4 were not established. These fields remain unknown rather than assumed.

Données vérifiées le : 2026-11-10 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

LM258PG4 datasheet LM258PG4 specifications LM258PG4 pinout LM258PG4 datasheet pdf LM258PG4 equivalent LM258PG4 replacement LM258PG4 vs LM2904P LM258PG4 vs LM358P LM258PG4 dual operational amplifier LM258PG4 30V op amp LM258PG8 PDIP LM258PG4 industrial amplifier LM258PG4 price Texas Instruments LM258PG4

Composants & termes associés

Texas Instruments LM258PG4 LM258 LM2904P LM358P TL072CP NXP Semiconductors dual operational amplifier general-purpose operational amplifier amplifier IC analog IC semiconductor internally compensated amplifier gain-bandwidth product slew rate quiescent current input common-mode range output voltage swing active filter sensor signal conditioning industrial control audio preamplifier 8-pin PDIP PDIP package through-hole assembly
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ