LM258PG4 - Dual 30V 700kHz Op Amp | Texas Instruments
MPN: LM258PG4 ✓ 啟用中LM258PG4 概覽
An operational amplifier is a high-gain analog building block used to amplify, buffer, filter, compare, or drive external signals. The LM258 belongs to the dual-operational-amplifier hierarchy within the broader categories of analog IC, amplifier IC, and semiconductor. Its internally compensated architecture simplifies design by eliminating the need for an external compensation network in typical closed-loop configurations.
The principal performance features include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and approximately 500 µA quiescent current per channel. These ratings make the device suitable for general-purpose voltage amplification, current-to-voltage conversion, active filtering, transducers, and industrial control loops. Its 30 V supply rating also provides additional headroom for industrial systems operating from higher-voltage rails than conventional low-voltage mixed-signal circuits.
Each channel contains an input differential pair, voltage-amplification stage, output stage, and internal frequency compensation. Because the amplifiers are independent, they can amplify two separate signals or be configured as one differential amplifier plus one additional signal channel. The 700 kHz bandwidth supports general-purpose closed-loop operation rather than the much wider bandwidth associated with precision, high-speed, or FET-input amplifier families.
Typical uses include sensor-interface amplification, industrial instrumentation, audio preamplification, active filters, relay and solenoid-driver stages, and low-frequency control systems. The dual configuration can reduce board area when two analog channels are required, while through-hole PDIP construction can simplify prototyping, inspection, and manual assembly.
Designers should verify input common-mode range, output swing, input bias current, offset voltage, noise, and output-current limits against the manufacturer datasheet for the selected operating point. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet rather than left open.
This product page combines the LM258PG4 family specifications, ordering information, package details, and practical selection guidance with same-footprint alternatives. It is intended to help engineers move from circuit requirements to a defensible dual-op-amp selection without relying on generic amplifier-family descriptions.
直接替換替代品,適用於 LM258PG4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM258PG4 (相同外形與佔位) — 差異在於 Mounting Type, Package, Slew Rate, Amplifier Type, Frequency Compensation.
LM2904P
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM258PG4 最大額定值與電氣特性
| Amplifier Type | General-purpose dual operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 30 V |
| Single-Supply Operating Range | 3 V to 32 V |
| 工作溫度範圍 | -25°C to +85°C |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| 靜態電流 | 500 µA per channel |
| Frequency Compensation | Internally compensated |
| 封裝 | 8-pin PDIP |
| 安裝類型 | Through-hole |
| Operating Voltage | 3 V to 32 V |
LM258PG4 8-pin pdip 腳位配置指南
LM258PG4(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM258PG4.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM258PG4 適用於 6 應用s: Industrial Sensor Signal Conditioning, Active Audio Preamplifier, Active Filter and Tone Control, Current-to-Voltage Measurement, Relay and Solenoid Driver Interface, General-Purpose Control Loop.
Industrial Sensor Signal Conditioning
The LM258PG4 fits low-frequency industrial sensor interfaces that require two analog channels, a supply span of 3 V to 32 V, and operation from -25°C to 85°C. Each internally compensated channel can amplify a sensor voltage, buffer it for an ADC, or form an active filter without an external compensation network. Its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate provide useful bandwidth for common pressure, temperature, and position sensors. Designers should still verify the input common-mode range, output swing, offset voltage, and bias-current requirements for the selected sensor and excitation level.
推薦
Active Audio Preamplifier
The LM258PG4 can provide two independent general-purpose audio preamplifier stages for mixer, monitoring, or line-level signal conditioning. A 700 kHz gain-bandwidth product covers the audible range with margin, while the 0.3 V/µs slew rate helps reproduce moderate-amplitude transients. The dual 8-pin PDIP package simplifies through-hole construction and allows one amplifier to serve the left channel while the other serves the right. For high-fidelity systems, verify input noise, output drive, distortion, and output-voltage swing against the manufacturer electrical characteristics.
推薦
Active Filter and Tone Control
The LM258PG4 is suitable for first-order or moderate-Q active-filter stages and tone-control networks because it combines internal frequency compensation with a 700 kHz gain-bandwidth product. A pair of amplifiers can implement a two-pole signal path or a dual-section filter, provided component tolerances and loop-gain requirements are considered. The 3 V to 32 V operating span supports both conventional ±15 V laboratory rails and lower single-supply systems after the signal and output ranges have been checked. The 0.3 V/µs slew rate should remain adequate for the intended bandwidth and signal amplitude.
推薦
Current-to-Voltage Measurement
The LM258PG4 can implement a transimpedance stage for low-frequency current measurements when the sensor current and feedback impedance produce acceptable operating voltage and bandwidth requirements. One channel performs current-to-voltage conversion, while the second channel can provide gain, offset correction, or active filtering. Its two-channel architecture reduces external amplification in instrumentation designs, and its internally compensated construction simplifies the feedback network. Confirm input bias current, input offset voltage, common-mode range, output swing, and stable feedback resistance before selecting the resistor values.
推薦
Relay and Solenoid Driver Interface
The LM258PG4 can provide the voltage gain needed between a low-level control signal and the input stage of a relay, solenoid, or indicator driver. Its 30 V maximum supply rating and 3 V to 32 V operating span suit higher-voltage industrial interfaces better than amplifiers limited to low supply rails. The two channels can control separate loads when each output stage operates within its voltage and current limits. Confirm output swing, output-current capability, load transients, and any flyback protection requirements; the operational amplifier itself may require an external driver transistor.
推薦
General-Purpose Control Loop
The LM258PG4 is suitable for proportional, integral, or general feedback-control prototypes where the loop bandwidth remains well below the 700 kHz device bandwidth. A single channel can implement the error amplifier while the second handles an auxiliary signal, monitor, or reference buffer. Its -25°C to 85°C operating range covers many industrial and commercial environments, and the internally compensated topology simplifies initial control-loop design. Verify loop stability, output swing, slew-rate margin, load behavior, and supply-noise performance before committing the amplifier to a compensation scheme.
推薦
推薦產品摘要
工程參考資料,適用於 LM258PG4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2904P | LM358P | TL072CP |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP | 8-pin PDIP - same | 8-pin PDIP - same | 8-pin PDIP - same |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels |
主要差異化特點
- Defined 30 V maximum supply rating (對比TL072CP)
- General-purpose dual internal compensation (對比TL072CP)
- Defined -25°C to +85°C operating range (對比LM358P)
- Two independent channels in one PDIP (對比LM2904P)
設計說明
Place the supply-decoupling network close to the LM258PG4 pins, with a short ground return to limit loop area. The device operates from 3 V to 32 V, but maximum supply voltage and total power dissipation must both be respected in high-voltage circuits. If the source rail can exceed 30 V during fault conditions, add appropriate protection rather than relying on normal operating tolerance.
Route each feedback path directly between the amplifier output and its inverting input, and keep input and output traces physically separated where practical. Maintain a continuous ground reference around the PDIP footprint and avoid long exposed traces that can couple adjacent-channel signals. Because the two channels share a package and supply pins, asymmetric or high-gain layouts can increase crosstalk and oscillation risk.
Do not assume that a shared 8-pin PDIP footprint guarantees drop-in equivalence. LM2904P, LM358P, and TL072CP differ in temperature grade, supply capability, input stage, bandwidth, or current behavior. Verify the exact pin mapping, input common-mode range, output swing, quiescent current, load capability, and stability requirements before modifying an existing LM258PG4 board.
合規資訊
The LM258 family is presented by the manufacturer as a general-purpose dual operational amplifier, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements for LM258PG4 were not established. These fields remain unknown rather than assumed.