LM258PG4 - Dual 30V 700kHz Op Amp | Texas Instruments
MPN: LM258PG4 ✓ AktifLM258PG4 Genel Bakış
An operational amplifier is a high-gain analog building block used to amplify, buffer, filter, compare, or drive external signals. The LM258 belongs to the dual-operational-amplifier hierarchy within the broader categories of analog IC, amplifier IC, and semiconductor. Its internally compensated architecture simplifies design by eliminating the need for an external compensation network in typical closed-loop configurations.
The principal performance features include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and approximately 500 µA quiescent current per channel. These ratings make the device suitable for general-purpose voltage amplification, current-to-voltage conversion, active filtering, transducers, and industrial control loops. Its 30 V supply rating also provides additional headroom for industrial systems operating from higher-voltage rails than conventional low-voltage mixed-signal circuits.
Each channel contains an input differential pair, voltage-amplification stage, output stage, and internal frequency compensation. Because the amplifiers are independent, they can amplify two separate signals or be configured as one differential amplifier plus one additional signal channel. The 700 kHz bandwidth supports general-purpose closed-loop operation rather than the much wider bandwidth associated with precision, high-speed, or FET-input amplifier families.
Typical uses include sensor-interface amplification, industrial instrumentation, audio preamplification, active filters, relay and solenoid-driver stages, and low-frequency control systems. The dual configuration can reduce board area when two analog channels are required, while through-hole PDIP construction can simplify prototyping, inspection, and manual assembly.
Designers should verify input common-mode range, output swing, input bias current, offset voltage, noise, and output-current limits against the manufacturer datasheet for the selected operating point. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet rather than left open.
This product page combines the LM258PG4 family specifications, ordering information, package details, and practical selection guidance with same-footprint alternatives. It is intended to help engineers move from circuit requirements to a defensible dual-op-amp selection without relying on generic amplifier-family descriptions.
Drop-in alternatifler için LM258PG4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LM258PG4 (aynı form faktörü ve ayağa oturma) — farklı olan Mounting Type, Package, Slew Rate, Amplifier Type, Frequency Compensation.
LM2904P
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM358P
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →TL072CP
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM258PG4 Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | General-purpose dual operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 30 V |
| Single-Supply Operating Range | 3 V to 32 V |
| İşletim Sıcaklığı Aralığı | -25°C to +85°C |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| Durağan Akım | 500 µA per channel |
| Frequency Compensation | Internally compensated |
| Paket | 8-pin PDIP |
| Montaj Türü | Through-hole |
| Operating Voltage | 3 V to 32 V |
LM258PG4 8-pin pdip Pin Yapısı Kılavuzu
LM258PG4 (8-pin pdip paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: LM258PG4.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
LM258PG4 için uygundur 6 uygulamas: Industrial Sensor Signal Conditioning, Active Audio Preamplifier, Active Filter and Tone Control, Current-to-Voltage Measurement, Relay and Solenoid Driver Interface, General-Purpose Control Loop.
Industrial Sensor Signal Conditioning
The LM258PG4 fits low-frequency industrial sensor interfaces that require two analog channels, a supply span of 3 V to 32 V, and operation from -25°C to 85°C. Each internally compensated channel can amplify a sensor voltage, buffer it for an ADC, or form an active filter without an external compensation network. Its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate provide useful bandwidth for common pressure, temperature, and position sensors. Designers should still verify the input common-mode range, output swing, offset voltage, and bias-current requirements for the selected sensor and excitation level.
Önerilen
Active Audio Preamplifier
The LM258PG4 can provide two independent general-purpose audio preamplifier stages for mixer, monitoring, or line-level signal conditioning. A 700 kHz gain-bandwidth product covers the audible range with margin, while the 0.3 V/µs slew rate helps reproduce moderate-amplitude transients. The dual 8-pin PDIP package simplifies through-hole construction and allows one amplifier to serve the left channel while the other serves the right. For high-fidelity systems, verify input noise, output drive, distortion, and output-voltage swing against the manufacturer electrical characteristics.
Önerilen
Active Filter and Tone Control
The LM258PG4 is suitable for first-order or moderate-Q active-filter stages and tone-control networks because it combines internal frequency compensation with a 700 kHz gain-bandwidth product. A pair of amplifiers can implement a two-pole signal path or a dual-section filter, provided component tolerances and loop-gain requirements are considered. The 3 V to 32 V operating span supports both conventional ±15 V laboratory rails and lower single-supply systems after the signal and output ranges have been checked. The 0.3 V/µs slew rate should remain adequate for the intended bandwidth and signal amplitude.
Önerilen
Current-to-Voltage Measurement
The LM258PG4 can implement a transimpedance stage for low-frequency current measurements when the sensor current and feedback impedance produce acceptable operating voltage and bandwidth requirements. One channel performs current-to-voltage conversion, while the second channel can provide gain, offset correction, or active filtering. Its two-channel architecture reduces external amplification in instrumentation designs, and its internally compensated construction simplifies the feedback network. Confirm input bias current, input offset voltage, common-mode range, output swing, and stable feedback resistance before selecting the resistor values.
Önerilen
Relay and Solenoid Driver Interface
The LM258PG4 can provide the voltage gain needed between a low-level control signal and the input stage of a relay, solenoid, or indicator driver. Its 30 V maximum supply rating and 3 V to 32 V operating span suit higher-voltage industrial interfaces better than amplifiers limited to low supply rails. The two channels can control separate loads when each output stage operates within its voltage and current limits. Confirm output swing, output-current capability, load transients, and any flyback protection requirements; the operational amplifier itself may require an external driver transistor.
Önerilen
General-Purpose Control Loop
The LM258PG4 is suitable for proportional, integral, or general feedback-control prototypes where the loop bandwidth remains well below the 700 kHz device bandwidth. A single channel can implement the error amplifier while the second handles an auxiliary signal, monitor, or reference buffer. Its -25°C to 85°C operating range covers many industrial and commercial environments, and the internally compensated topology simplifies initial control-loop design. Verify loop stability, output swing, slew-rate margin, load behavior, and supply-noise performance before committing the amplifier to a compensation scheme.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LM258PG4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LM2904P | LM358P | TL072CP |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP | 8-pin PDIP - same | 8-pin PDIP - same | 8-pin PDIP - same |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels |
Ana Farklılayıcılar
- Defined 30 V maximum supply rating (karşılaştırma:TL072CP)
- General-purpose dual internal compensation (karşılaştırma:TL072CP)
- Defined -25°C to +85°C operating range (karşılaştırma:LM358P)
- Two independent channels in one PDIP (karşılaştırma:LM2904P)
Tasarım Notları
Place the supply-decoupling network close to the LM258PG4 pins, with a short ground return to limit loop area. The device operates from 3 V to 32 V, but maximum supply voltage and total power dissipation must both be respected in high-voltage circuits. If the source rail can exceed 30 V during fault conditions, add appropriate protection rather than relying on normal operating tolerance.
Route each feedback path directly between the amplifier output and its inverting input, and keep input and output traces physically separated where practical. Maintain a continuous ground reference around the PDIP footprint and avoid long exposed traces that can couple adjacent-channel signals. Because the two channels share a package and supply pins, asymmetric or high-gain layouts can increase crosstalk and oscillation risk.
Do not assume that a shared 8-pin PDIP footprint guarantees drop-in equivalence. LM2904P, LM358P, and TL072CP differ in temperature grade, supply capability, input stage, bandwidth, or current behavior. Verify the exact pin mapping, input common-mode range, output swing, quiescent current, load capability, and stability requirements before modifying an existing LM258PG4 board.
Uyumluluk Bilgisi
The LM258 family is presented by the manufacturer as a general-purpose dual operational amplifier, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements for LM258PG4 were not established. These fields remain unknown rather than assumed.