LM258PG4 - Dual 30V 700kHz Op Amp | Texas Instruments
料号: LM258PG4 ✓ 量产中LM258PG4 概述
An operational amplifier is a high-gain analog building block used to amplify, buffer, filter, compare, or drive external signals. The LM258 belongs to the dual-operational-amplifier hierarchy within the broader categories of analog IC, amplifier IC, and semiconductor. Its internally compensated architecture simplifies design by eliminating the need for an external compensation network in typical closed-loop configurations.
The principal performance features include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and approximately 500 µA quiescent current per channel. These ratings make the device suitable for general-purpose voltage amplification, current-to-voltage conversion, active filtering, transducers, and industrial control loops. Its 30 V supply rating also provides additional headroom for industrial systems operating from higher-voltage rails than conventional low-voltage mixed-signal circuits.
Each channel contains an input differential pair, voltage-amplification stage, output stage, and internal frequency compensation. Because the amplifiers are independent, they can amplify two separate signals or be configured as one differential amplifier plus one additional signal channel. The 700 kHz bandwidth supports general-purpose closed-loop operation rather than the much wider bandwidth associated with precision, high-speed, or FET-input amplifier families.
Typical uses include sensor-interface amplification, industrial instrumentation, audio preamplification, active filters, relay and solenoid-driver stages, and low-frequency control systems. The dual configuration can reduce board area when two analog channels are required, while through-hole PDIP construction can simplify prototyping, inspection, and manual assembly.
Designers should verify input common-mode range, output swing, input bias current, offset voltage, noise, and output-current limits against the manufacturer datasheet for the selected operating point. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet rather than left open.
This product page combines the LM258PG4 family specifications, ordering information, package details, and practical selection guidance with same-footprint alternatives. It is intended to help engineers move from circuit requirements to a defensible dual-op-amp selection without relying on generic amplifier-family descriptions.
直接替换替代料: LM258PG4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM258PG4 (相同外形与封装尺寸) ——差异在于 Mounting Type, Package, Slew Rate, Amplifier Type, Frequency Compensation.
LM2904P
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM258PG4 最大额定值与电气特性
| Amplifier Type | General-purpose dual operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 30 V |
| Single-Supply Operating Range | 3 V to 32 V |
| 工作温度范围 | -25°C to +85°C |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| 静态电流 | 500 µA per channel |
| Frequency Compensation | Internally compensated |
| 封装 | 8-pin PDIP |
| 安装类型 | Through-hole |
| Operating Voltage | 3 V to 32 V |
LM258PG4 8-pin pdip 引脚配置指南
LM258PG4(8-pin pdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM258PG4.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM258PG4 适用于 6 应用s: Industrial Sensor Signal Conditioning, Active Audio Preamplifier, Active Filter and Tone Control, Current-to-Voltage Measurement, Relay and Solenoid Driver Interface, General-Purpose Control Loop.
Industrial Sensor Signal Conditioning
The LM258PG4 fits low-frequency industrial sensor interfaces that require two analog channels, a supply span of 3 V to 32 V, and operation from -25°C to 85°C. Each internally compensated channel can amplify a sensor voltage, buffer it for an ADC, or form an active filter without an external compensation network. Its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate provide useful bandwidth for common pressure, temperature, and position sensors. Designers should still verify the input common-mode range, output swing, offset voltage, and bias-current requirements for the selected sensor and excitation level.
推荐
Active Audio Preamplifier
The LM258PG4 can provide two independent general-purpose audio preamplifier stages for mixer, monitoring, or line-level signal conditioning. A 700 kHz gain-bandwidth product covers the audible range with margin, while the 0.3 V/µs slew rate helps reproduce moderate-amplitude transients. The dual 8-pin PDIP package simplifies through-hole construction and allows one amplifier to serve the left channel while the other serves the right. For high-fidelity systems, verify input noise, output drive, distortion, and output-voltage swing against the manufacturer electrical characteristics.
推荐
Active Filter and Tone Control
The LM258PG4 is suitable for first-order or moderate-Q active-filter stages and tone-control networks because it combines internal frequency compensation with a 700 kHz gain-bandwidth product. A pair of amplifiers can implement a two-pole signal path or a dual-section filter, provided component tolerances and loop-gain requirements are considered. The 3 V to 32 V operating span supports both conventional ±15 V laboratory rails and lower single-supply systems after the signal and output ranges have been checked. The 0.3 V/µs slew rate should remain adequate for the intended bandwidth and signal amplitude.
推荐
Current-to-Voltage Measurement
The LM258PG4 can implement a transimpedance stage for low-frequency current measurements when the sensor current and feedback impedance produce acceptable operating voltage and bandwidth requirements. One channel performs current-to-voltage conversion, while the second channel can provide gain, offset correction, or active filtering. Its two-channel architecture reduces external amplification in instrumentation designs, and its internally compensated construction simplifies the feedback network. Confirm input bias current, input offset voltage, common-mode range, output swing, and stable feedback resistance before selecting the resistor values.
推荐
Relay and Solenoid Driver Interface
The LM258PG4 can provide the voltage gain needed between a low-level control signal and the input stage of a relay, solenoid, or indicator driver. Its 30 V maximum supply rating and 3 V to 32 V operating span suit higher-voltage industrial interfaces better than amplifiers limited to low supply rails. The two channels can control separate loads when each output stage operates within its voltage and current limits. Confirm output swing, output-current capability, load transients, and any flyback protection requirements; the operational amplifier itself may require an external driver transistor.
推荐
General-Purpose Control Loop
The LM258PG4 is suitable for proportional, integral, or general feedback-control prototypes where the loop bandwidth remains well below the 700 kHz device bandwidth. A single channel can implement the error amplifier while the second handles an auxiliary signal, monitor, or reference buffer. Its -25°C to 85°C operating range covers many industrial and commercial environments, and the internally compensated topology simplifies initial control-loop design. Verify loop stability, output swing, slew-rate margin, load behavior, and supply-noise performance before committing the amplifier to a compensation scheme.
推荐
推荐产品汇总
工程参考数据: LM258PG4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2904P | LM358P | TL072CP |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP | 8-pin PDIP - same | 8-pin PDIP - same | 8-pin PDIP - same |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels |
关键差异点
- Defined 30 V maximum supply rating (对比 TL072CP)
- General-purpose dual internal compensation (对比 TL072CP)
- Defined -25°C to +85°C operating range (对比 LM358P)
- Two independent channels in one PDIP (对比 LM2904P)
设计说明
Place the supply-decoupling network close to the LM258PG4 pins, with a short ground return to limit loop area. The device operates from 3 V to 32 V, but maximum supply voltage and total power dissipation must both be respected in high-voltage circuits. If the source rail can exceed 30 V during fault conditions, add appropriate protection rather than relying on normal operating tolerance.
Route each feedback path directly between the amplifier output and its inverting input, and keep input and output traces physically separated where practical. Maintain a continuous ground reference around the PDIP footprint and avoid long exposed traces that can couple adjacent-channel signals. Because the two channels share a package and supply pins, asymmetric or high-gain layouts can increase crosstalk and oscillation risk.
Do not assume that a shared 8-pin PDIP footprint guarantees drop-in equivalence. LM2904P, LM358P, and TL072CP differ in temperature grade, supply capability, input stage, bandwidth, or current behavior. Verify the exact pin mapping, input common-mode range, output swing, quiescent current, load capability, and stability requirements before modifying an existing LM258PG4 board.
合规信息
The LM258 family is presented by the manufacturer as a general-purpose dual operational amplifier, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements for LM258PG4 were not established. These fields remain unknown rather than assumed.