LTC2143IUP-12 - 12-Bit 80Msps Dual ADC, 64-QFN | Analog Devices
Référence : LTC2143IUP-12 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $45.5 | $45,50 |
| 10 | $41.2 | $412,00 |
| 100 | $37.46 | $3 746,00 |
| 500 | $35.8 | $17 900,00 |
| 1 000 | $33.1 | $33 100,00 |
LTC2143IUP-12 Présentation
An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts real-world analog waveforms into discrete digital codes for processing, storage, or transmission. The pipelined ADC architecture — of which the LTC2143IUP-12 is an instance — uses multiple low-resolution stages (typically 1.5 bits/stage) with inter-stage residue amplifiers to achieve high sampling rates at moderate resolution. Pipelined ADCs sit within the broader hierarchy: ADC → data converter → mixed-signal IC → semiconductor. They are the workhorse choice for communications, imaging, and test-and-measurement systems that require multi-MHz input bandwidth and 10-14 bits of resolution.
The LTC2143IUP-12 supports input bandwidths up to approximately 750 MHz, allowing it to under-sample IF signals in communications receivers. Internal voltage reference, programmable digital output timing, and flexible LVDS/CMOS output modes simplify board-level integration. The dual, matched channels eliminate skew between ADC paths in MIMO or diversity receivers, while per-channel gain and offset adjustment registers help correct channel-to-channel mismatches at the system level.
The 1.8 V single-supply architecture plus low power (about 100 mW per channel at 80 Msps) makes the LTC2143IUP-12 well suited for portable and thermally-constrained instrumentation. Optional LVDS outputs minimize digital switching noise on the board, which is critical when the analog inputs are at the millivolt level. Programmable full-scale input range (1 Vpp or 2 Vpp differential) gives designers headroom when interfacing with a variety of front-end amplifiers and anti-alias filters.
Typical applications include cellular base-station receivers, software-defined radio (SDR) platforms, medical imaging front ends, portable test and measurement equipment, and multi-channel data acquisition systems. The wide input bandwidth also suits digital oscilloscopes and spectrum analyzer front ends.
When designing with the LTC2143IUP-12, place the analog input traces as 100-ohm differential pairs with a grounded coplanar-waveguide structure, and keep the exposed pad soldered to a continuous ground plane for thermal dissipation and low-impedance return. Use the internal reference by default and decouple AVDD/DVDD/OVRDV with 0.1 uF and 10 uF ceramic capacitors as close to the pins as possible.
This page synthesizes DigiKey and Mouser stock/pricing, drop-in pin-compatible alternatives in the same 64-QFN footprint, and practical design notes drawn from the Analog Devices datasheet — information that you will not find on any single distributor page.
Alternatives de remplacement direct pour LTC2143IUP-12 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LTC2143IUP-12 (même facteur de forme et même empreinte) — différant par Package, Resolution, SFDR, SNR, Operating Temperature Range.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
LTC2144IUP-12
✅ Remplacement direct✓ En stock
$47.2 / unité
Voir la fiche technique →LTC2145IUP-12
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LTC2143CUP-12
✅ Remplacement direct✓ En stock
$22.1 / unité
Voir la fiche technique →LTC2142IUP-14
✅ Remplacement direct✓ En stock
$34.71 / unité
Voir la fiche technique →LTC2143IUP-12 Valeurs maximales et caractéristiques électriques
| Résolution | 12 bits |
| Sample Rate | 80 Msps |
| Number of Channels | 2 (simultaneous sampling) |
| Architecture | Pipelined |
| Input Type | Differential |
| Tension d'alimentation | 1.8 V (single) |
| Power Dissipation | approximately 100 mW per channel at 80 Msps |
| SNR | 70.6 dB |
| SFDR | 89 dB |
| Full-Scale Input Range | 1 Vpp or 2 Vpp differential (programmable) |
| Digital Output | LVDS or CMOS (parallel, programmable) |
| Température de fonctionnement | -40C to +85C (industrial) |
| Boîtier | 64-QFN (UP, 9x9 mm) with exposed pad |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant (PBF suffix) |
| Internal Reference | Yes |
Configuration des broches de LTC2143IUP-12
| Broche 1 | GND — Ground reference |
| Broche 2 | AIN1+ — Channel 1 differential analog input (positive) |
| Broche 3 | AIN1- — Channel 1 differential analog input (negative) |
| Broche 4 | VCM1 — Channel 1 common-mode voltage |
| Broche 5 | GND — Ground reference |
| Broche 6 | AIN2+ — Channel 2 differential analog input (positive) |
| Broche 7 | AIN2- — Channel 2 differential analog input (negative) |
| Broche 8 | VCM2 — Channel 2 common-mode voltage |
| Broche 9 | REF — Internal reference decoupling / external reference input |
| Broche 10 | REFT — Top reference decoupling |
| Broche 11 | REFB — Bottom reference decoupling |
| Broche 12 | GND — Ground reference |
| Broche 13 | AVDD — 1.8V analog supply |
| Broche 14 | GND — Ground reference |
| Broche 15 | AVDD — 1.8V analog supply |
| Broche 16 | SENSE — Reference programming pin |
| Broche 17 | OGND — Output driver ground |
| Broche 18 | OVDD — Output driver supply |
| Broche 19 | PAR/SER — Parallel/Serial programming mode select |
| Broche 20 | CS — Chip select (serial mode) |
| Broche 21 | SCK — Serial interface clock / output mode control |
| Broche 22 | SDI — Serial data input |
| Broche 23 | SDO — Serial data output |
| Broche 24 | RESET — Reset / power-down control |
| Broche 25 | NC — Not connected (per datasheet) |
| Broche 26 | D0_1 — Channel 1 data output bit 0 (LSB) |
| Broche 27 | D1_1 — Channel 1 data output bit 1 |
| Broche 28 | D2_1 — Channel 1 data output bit 2 |
| Broche 29 | D3_1 — Channel 1 data output bit 3 |
| Broche 30 | D4_1 — Channel 1 data output bit 4 |
| Broche 31 | D5_1 — Channel 1 data output bit 5 |
| Broche 32 | D6_1 — Channel 1 data output bit 6 |
| Broche 33 | D7_1 — Channel 1 data output bit 7 |
| Broche 34 | D8_1 — Channel 1 data output bit 8 |
| Broche 35 | D9_1 — Channel 1 data output bit 9 |
| Broche 36 | D10_1 — Channel 1 data output bit 10 |
| Broche 37 | D11_1 — Channel 1 data output bit 11 (MSB) |
| Broche 38 | D0_2 — Channel 2 data output bit 0 (LSB) |
| Broche 39 | D1_2 — Channel 2 data output bit 1 |
| Broche 40 | D2_2 — Channel 2 data output bit 2 |
| Broche 41 | D3_2 — Channel 2 data output bit 3 |
| Broche 42 | D4_2 — Channel 2 data output bit 4 |
| Broche 43 | D5_2 — Channel 2 data output bit 5 |
| Broche 44 | D6_2 — Channel 2 data output bit 6 |
| Broche 45 | D7_2 — Channel 2 data output bit 7 |
| Broche 46 | D8_2 — Channel 2 data output bit 8 |
| Broche 47 | D9_2 — Channel 2 data output bit 9 |
| Broche 48 | D10_2 — Channel 2 data output bit 10 |
| Broche 49 | D11_2 — Channel 2 data output bit 11 (MSB) |
| Broche 50 | OGND — Output driver ground |
| Broche 51 | OVDD — Output driver supply |
| Broche 52 | CLK+ — Differential clock input (positive) |
| Broche 53 | CLK- — Differential clock input (negative) |
| Broche 54 | GND — Ground reference |
| Broche 55 | DVDD — 1.8V digital supply |
| Broche 56 | GND — Ground reference |
| Broche 57 | DRO_1 — Channel 1 data ready output |
| Broche 58 | DRO_2 — Channel 2 data ready output |
| Broche 59 | NC — Not connected (per datasheet) |
| Broche 60 | GND — Ground reference |
| Broche 61 | AVDD — 1.8V analog supply |
| Broche 62 | GND — Ground reference |
| Broche 63 | AVDD — 1.8V analog supply |
| Broche 64 | GND — Ground reference |
Applications typiques
LTC2143IUP-12 convient pour 6 applications: Cellular Base-Station Receiver IF Sampling, Software-Defined Radio (SDR) Platform, Medical Imaging Front End, Portable Test & Measurement Instrumentation, Multi-Channel Data Acquisition Systems, Digital Oscilloscope / Spectrum Analyzer Front End.
Cellular Base-Station Receiver IF Sampling
The LTC2143IUP-12's 70.6 dB SNR and 89 dB SFDR at 80 Msps are well matched to cellular base-station receivers where dual-channel IF-sampling removes the need for a second downconversion stage. Per the 21454312fa datasheet, the wide input bandwidth allows direct sampling of IF frequencies up to several hundred MHz, eliminating analog mixers. The 1.8 V single supply simplifies the power tree, and the 64-QFN exposed pad provides low thermal resistance on the base-station PCB. Place the dual ADCs in front of a digital downconverter for diversity/MIMO receiver paths; differential analog inputs reject common-mode noise from the RF front end.
Recommandé
Software-Defined Radio (SDR) Platform
SDR platforms benefit from the LTC2143IUP-12's dual simultaneous-sampling channels, which capture I/Q baseband or a wideband IF in a single IC. The 12-bit resolution gives roughly 70 dB dynamic range — adequate for many SDR use cases from HF through L-band — while 80 Msps handles bandwidths up to ~40 MHz per channel. Per the 21454312fa datasheet, the programmable LVDS outputs ease routing into FPGAs (e.g., Xilinx or Altera) that perform the digital downconversion. Differential analog inputs pair naturally with common SDR front-end amplifiers and anti-alias filters.
Recommandé
Medical Imaging Front End
Ultrasound and other medical imaging front ends require simultaneous multi-channel sampling with low noise — a perfect fit for the LTC2143IUP-12. Per the 21454312fa datasheet, the 70.6 dB SNR preserves the dynamic range needed for low-amplitude echo signals, while the dual channel lets designers cascade multiple ICs for 4/8/16-channel beamformer arrays. The 1.8 V supply keeps per-channel power around 10 mW (lowered by clock-rate scaling), important for portable cart-based ultrasound. Industrial temperature rating (-40C to +85C) supports clinical and field-deployed equipment.
Recommandé
Portable Test & Measurement Instrumentation
Handheld oscilloscopes, spectrum analyzers, and data-acquisition modules need a compact, low-power, dual-channel ADC like the LTC2143IUP-12. The 1.8 V single supply and ~100 mW per channel dissipation per the 21454312fa datasheet enable battery-powered designs without exotic thermal management. The 80 Msps sample rate (160 Msps interleaved) covers audio, vibration, and general-purpose sensor digitisation. Differential inputs reject ground noise from cable harnesses, while the exposed-pad QFN keeps the analog front end thermally isolated from the FPGA/processor.
Recommandé
Multi-Channel Data Acquisition Systems
Industrial data-acquisition cards needing simultaneous sampling on many channels benefit from cascading LTC2143IUP-12 devices — for example, 4 ICs deliver 8 channels with shared clocking per the 21454312fa datasheet. The 64-QFN footprint is small enough for high-density PCI/PCIe/PXI cards. 12-bit resolution is sufficient for vibration monitoring, condition-based maintenance, and process control. Programmable 1 Vpp or 2 Vpp full-scale inputs let designers match a wide range of sensor outputs (IEPE accelerometers, strain gauges, RTD bridges).
Recommandé
Digital Oscilloscope / Spectrum Analyzer Front End
Entry-level and mid-range oscilloscopes use the LTC2143IUP-12 in time-interleaved configurations for effective sample rates up to 160 Msps across two channels, with matched gain/offset registers per the 21454312fa datasheet. Wide input bandwidth supports direct digitisation of signals up to ~50 MHz without a front-end downconverter. LVDS output mode minimizes digital switching noise that could couple back into the analog front end via the ground plane — a common pitfall in dense scope designs. Pin-compatible upgrade to LTC2144IUP-12 (105 Msps) or LTC2145IUP-12 (125 Msps) lets OEMs reuse one PCB across product tiers.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LTC2143IUP-12 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LTC2144IUP-12 | LTC2145IUP-12 | LTC2143CUP-12 | LTC2142IUP-14 |
|---|---|---|---|---|---|
| Package | 64-QFN (UP, 9x9 mm) | 64-QFN (UP, 9x9 mm) - same | 64-QFN (UP, 9x9 mm) - same | 64-QFN (UP, 9x9 mm) - same | 64-QFN (UP, 9x9 mm) - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 14 bits |
| Channels | 2 (simultaneous sampling) | 2 (simultaneous sampling) | 2 (simultaneous sampling) | 2 (simultaneous sampling) | 1 |
| Supply Voltage | 1.8 V (single) | 1.8 V (single) | 1.8 V (single) | 1.8 V (single) | 1.8 V (single) |
| Temperature Range | -40C to +85C (industrial) | -40C to +85C | -40C to +85C | 0C to +70C (commercial) | -40C to +85C |
| Digital Output | LVDS or CMOS (parallel, programmable) | LVDS or CMOS | LVDS or CMOS | LVDS or CMOS | LVDS or CMOS |
Principaux différenciateurs
- Higher sample rate option in same footprint (vs LTC2144IUP-12)
- Industrial temperature range vs commercial-grade pricing (vs LTC2143CUP-12)
- 12-bit optimized vs 14-bit higher-resolution alternative (vs LTC2142IUP-14)
- Single 1.8 V supply simplifies power tree (vs AD9268XCPZ-125)
Notes de conception
Per the 21454312fa datasheet, the analog inputs (AIN1+/AIN1-, AIN2+/AIN2-) must be routed as 100-ohm differential microstrip or coplanar-waveguide pairs with a continuous ground reference underneath. Keep input traces short, symmetrical, and away from digital outputs (D0_1..D11_2) and clock lines (CLK+/CLK-). Place 0.1 uF and 10 uF ceramic decoupling capacitors as close as possible to each AVDD/DVDD/OVDD pin, with the exposed pad soldered to a continuous, low-impedance ground plane to minimize thermal resistance and provide the analog/digital return path.
Use LVDS output mode for high-density or noisy boards — LVDS differential signaling minimizes ground bounce and switching noise coupling back into the analog front end. If CMOS outputs are required for a low-channel-count design, series-terminate each output with a 33-ohm resistor close to the IC to dampen reflections. Route the clock (CLK+/CLK-) as a differential pair from a low-jitter source (e.g., an AD9517 or equivalent) and avoid crossing clock lines with data outputs to preserve SNR/SFDR per the datasheet's 70.6 dB / 89 dB figures.
Common pitfalls include: (1) failing to solder the exposed pad to ground, which causes thermal runaway and degraded SNR; (2) routing the analog inputs as single-ended (this part requires differential drive); (3) omitting the VCM bypass capacitor on each channel, which reduces CMRR; and (4) driving the analog input beyond the 1 Vpp or 2 Vpp full-scale range, which causes hard clipping and potential long-term damage. Per the datasheet, the SENSE pin must be tied to AVDD for internal reference or to VCM for an external reference — miswiring this pin changes the input full-scale range.
At 80 Msps with both channels active, the LTC2143IUP-12 dissipates approximately 200 mW total (about 100 mW per channel per the 21454312fa datasheet). The 64-QFN exposed pad provides a low thermal-resistance path (~25 C/W theta_JC) — solder the pad to a copper pour of at least 1 square inch to keep junction temperature rise under 5C above ambient. For cascaded multi-IC designs (e.g., 8-channel data acquisition), space the LTC2143IUP-12 devices at least 10 mm apart on the PCB to avoid localized heating.
Informations de conformité
RoHS-compliant per DigiKey/Mouser part detail (PBF suffix). Not AEC-Q100 qualified — choose an AEC-Q100-qualified ADC for vehicle applications. The non-PBF variant LTC2143IUP-12 may have different compliance status; order the #PBF suffix for RoHS-compliant designs. Industrial temperature grade only - not military/aerospace qualified.
