MCF52210CAE66 - 32-Bit 66 MHz ColdFire MCU | NXP
Référence : MCF52210CAE66 ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $6.4464 | $6,45 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1 000 | $0 | $0,00 |
MCF52210CAE66 Présentation
A ColdFire microcontroller is a 32-bit embedded processor architecture used in control-oriented products such as industrial equipment, communications modules, human-machine interfaces, and USB peripherals. The ColdFire V2 core provides a deterministic instruction set and a conventional microcontroller integration model, allowing firmware to control memory-mapped peripherals, communications interfaces, timers, and external devices.
The supplied product data identifies the MCF52210CAE66 as a ColdFire V2 MCF5221x device with 66 MHz operation, 64 KB Flash, and a 64-LQFP package. The NXP product listing also describes it as a 32-bit microcontroller with USB capability. These characteristics make the device suitable for embedded USB controllers, peripheral hubs, industrial controllers, and compact communication equipment where a higher-performance 32-bit core is useful without adopting a larger MCU package.
The 64 KB Flash memory provides on-chip nonvolatile program storage, reducing the need for an external program-memory device in firmware-contained designs. The 10 x 10 mm LQFP provides 64 leads for power, ground, communications, control, and peripheral connectivity. Because the verified excerpt does not specify the complete electrical limits or pin-level multiplexing, engineers should use the manufacturer datasheet before finalizing power, clock, USB, and signal-integrity implementation details.
Typical design work includes confirming the required USB interface, validating the clock source and reset behavior, checking peripheral pin multiplexing, and planning programming and test access. LQFP packages also require adequate soldering and inspection practices during manufacturing. The compact 10 x 10 mm footprint helps reduce board area but does not eliminate thermal or routing constraints.
This product page distinguishes the MCF52210CAE66 from broader cross-reference candidates by focusing on the verified 32-bit ColdFire V2 architecture, 66 MHz frequency, 64 KB Flash configuration, USB association, and 64-LQFP package. Confirm current lifecycle, pinout, electrical limits, and availability with NXP or an authorized distributor before committing to a production design.
Alternatives de remplacement direct pour MCF52210CAE66 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MCF52210CAE66 (même facteur de forme et même empreinte) — différant par Package, Core, RAM, Supply Voltage, Flash Memory.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
MCF52100CAE66
✅ Remplacement direct✓ En stock
$5.09 / unité
Voir la fiche technique →MCF52110CAE66
✅ Remplacement direct✓ En stock
$9.95 / unité
Voir la fiche technique →MCF52211CAE66
✅ Remplacement direct✓ En stock
$9.25 / unité
Voir la fiche technique →MCF52212CAE50
✅ Remplacement direct✓ En stock
$6.74 / unité
Voir la fiche technique →MCF52221CAE66
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →MCF52210CAE66 Valeurs maximales et caractéristiques électriques
| Microcontroller Type | 32-bit ColdFire V2 microcontroller |
| Processor Architecture | ColdFire V2 RISC |
| Fréquence d'horloge maximale | 66 MHz |
| Flash Memory | 64 KB |
| Program Memory Organization | 64K x 8 |
| USB Association | USB |
| Package Type | 64-LQFP (10 x 10 mm) |
| Package Pin Count | 64 pins |
| Type de montage | Surface Mount |
| Core | ColdFire V2 |
| Tension d'alimentation | 3.3 V |
| Manufacturer | NXP Semiconductors |
| Legacy Manufacturer | Freescale Semiconductor |
| Data Width | 32-bit |
| Type de mémoire | Flash |
| Product Category | 32-bit Microcontroller IC |
Guide de configuration des broches du MCF52210CAE66 64 pins
Configuration des broches du MCF52210CAE66 (boîtier 64 pins). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour MCF52210CAE66.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MCF52210CAE66 convient pour 7 applications: USB Embedded Peripheral Controller, Industrial Control Module, Human-Machine Interface Controller, USB Communication Gateway, Data Acquisition Front End, Programmable Automation Controller, Connected Service Interface.
USB Embedded Peripheral Controller
The MCF52210CAE66 fits a compact USB-enabled embedded peripheral when the product listing’s 66 MHz ColdFire V2 core and 64 KB Flash are sufficient for local control and firmware storage. The MCU can coordinate device state, protocol handling, configuration storage, and host-facing controls in a 10 x 10 mm LQFP footprint. Designers should verify USB device or host capability, transceiver dependency, power states, and exact pin assignments in the NXP datasheet. Keep USB routing short and controlled, and provide the required clock, reset, decoupling, and programming access according to the manufacturer guidance.
Recommandé
Industrial Control Module
The 32-bit ColdFire V2 architecture and 66 MHz operating frequency provide a practical basis for an industrial control module that coordinates digital I/O, communications, timers, and supervisory logic. Its 64 KB Flash allows a compact firmware image to be stored on-chip, while the 64-LQFP package preserves a relatively compact surface-mount footprint. The exact I/O count, peripheral availability, voltage limits, and pin multiplexing are not included in the supplied excerpts. Before schematic release, compare the complete datasheet against the required sensors, actuators, isolation boundaries, bus levels, and factory update method.
Recommandé
Human-Machine Interface Controller
MCF52210CAE66 can serve as the central controller for a compact human-machine interface when the interface includes a display, keypad, status LEDs, and a communications link. Its verified 32-bit ColdFire V2 core and 66 MHz clock are useful for responsive event handling and peripheral coordination, while 64 KB Flash supports embedded control firmware. The designer must still verify available I/O pins, timing peripherals, external memory interfaces, and operating-temperature limits from the manufacturer datasheet. Use a defined ground and reset strategy, isolate display buses from USB or switching circuitry, and validate ESD protection at externally accessible connectors.
Recommandé
USB Communication Gateway
The product is a logical candidate for a USB communication gateway because the verified distributor data identifies USB capability alongside a 32-bit ColdFire V2 processor at 66 MHz. The controller can bridge a local serial or industrial interface to a USB-connected host while maintaining protocol state and diagnostics in its 64 KB Flash. The actual gateway architecture depends on the selected USB mode, available communications peripherals, and required transceiver components, none of which are fully specified in the supplied snippets. Validate signal integrity, ESD protection, bus termination, firmware update strategy, and enumeration behavior before production release.
Recommandé
Data Acquisition Front End
MCF52210CAE66 can coordinate a compact data-acquisition front end that gathers digital measurements and passes processed data through a communications interface. The 32-bit architecture and 66 MHz operating point provide a stronger control platform than an 8- or 16-bit MCU for multi-step sampling coordination, buffering, and protocol formatting, while 64 KB Flash limits the available program and constant-data space to the designer. ADC characteristics, timer channels, sensor interfaces, and memory details are not present in the supplied data. Confirm them in the manufacturer datasheet and design input filtering and grounding around the actual sensor requirements.
Recommandé
Programmable Automation Controller
The MCF52210CAE66 is suitable for a small programmable automation controller when the application needs a 32-bit control core, on-chip Flash, and a compact LQFP footprint. It can manage discrete I/O, sequence logic, communications, and fault reporting, provided the selected pinout and peripheral resources satisfy the machine requirements. The verified material does not establish isolated I/O channels, safety rating, motion-control features, or environmental limits, so those requirements must be treated as external interface and system-level design tasks. Validate startup behavior, watchdog requirements, brownout behavior, and field programming access against the final product specification.
Recommandé
Connected Service Interface
MCF52210CAE66 can be integrated into a connected service interface that exposes configuration, diagnostics, or firmware-update functions through USB or another communications channel. Its 66 MHz ColdFire V2 core can handle protocol tasks and control logic, while 64 KB Flash may be adequate for a focused firmware image. The design should use a separate service connector protection strategy, robust ground and power sequencing, and a controlled bootloader path. The verified results identify USB association but do not provide security capabilities, update endurance, authentication features, or exact USB electrical requirements; those items must be confirmed from the full NXP documentation.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MCF52210CAE66 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MCF52100CAE66 | MCF52110CAE66 | MCF52211CAE66 | MCF52212CAE50 | MCF52221CAE66 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10 x 10 mm) | 64-LQFP (10 x 10 mm) | 64-LQFP (10 x 10 mm) | 64-LQFP (10 x 10 mm) | LQFP | 64-LQFP (10 x 10 mm) |
Principaux différenciateurs
- Verified 66 MHz operating frequency (vs MCF52100CAE66)
- Verified 64 KB on-chip Flash (vs MCF52110CAE66)
- USB-associated control positioning (vs MCF52211CAE66)
- Documented package identity (vs MCF52212CAE50)
Notes de conception
Use the manufacturer land pattern for the 64-LQFP 10 x 10 mm package rather than estimating dimensions from the distributor description. Confirm pad length, pad width, exposed thermal requirements if any, and solder-mask clearance against the package drawing. Place the MCU close to its clock, reset, decoupling, USB, and programming nets, and avoid routing high-current switching paths beneath sensitive signal traces.
The verified listing identifies a 3.3 V supply, but it does not provide the complete electrical limits or recommended decoupling values. Before power-up, verify supply range, absolute maximum ratings, input leakage, power sequencing, and ground requirements in the NXP datasheet. Use only manufacturer-recommended capacitor values and placement; do not substitute generic values when the device-specific power network has not been validated.
Do not treat a same-family or same-package MPN as a drop-in replacement without checking every pin and peripheral function. The verified data confirms the target’s 64-LQFP package and basic identity, but it does not establish identical USB routing, clock pins, memory mapping, interrupt vectors, or peripheral multiplexing for MCF52100CAE66, MCF52110CAE66, MCF52211CAE66, MCF52212CAE50, or MCF52221CAE66. Compare the complete datasheets and validate firmware after any substitution.
For USB-enabled use, keep the USB data path short, preserve the referenced ground connection, and separate the USB route from clocks, switching inductors, and high-current motor returns. Confirm whether the selected MCU variant uses an integrated transceiver or requires external components. Apply the manufacturer’s recommended termination and protection scheme; the supplied search snippets do not establish the exact USB electrical topology.
Although the target is a microcontroller rather than a power semiconductor, power dissipation still depends on clock activity, I/O loading, USB activity, and supply voltage. Estimate worst-case internal and I/O dissipation only after obtaining the datasheet current limits and operating modes. Provide adequate copper area and thermal relief according to the package drawing, and avoid using an assumed thermal resistance or junction-temperature rise for production safety decisions.
Informations de conformité
The supplied distributor snippets do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-mineral status. Confirm current compliance and lifecycle information with NXP or an authorized distributor.
