MPC8360ZUAGDGA - 400MHz PowerQUICC II Pro MPU | NXP
Référence : MPC8360ZUAGDGA ✓ ActifMPC8360ZUAGDGA Présentation
PowerQUICC II Pro processors are integrated communications processors that combine a Power Architecture CPU core with a peripheral subsystem optimized for WAN, LAN, and wireless protocol termination. Within the broader product taxonomy they sit between general-purpose embedded CPUs and dedicated network processors, and are widely used in routers, DSLAM line cards, industrial control, and secure access equipment where deterministic communications throughput matters more than raw GHz. The 'non-ENCRP' suffix indicates the silicon security/firmware module is not enabled in this part number, distinguishing it from the MPC8360E sister devices.
Key features include the e300 superscalar core with separate 32KB instruction and 32KB data caches, dual DDR1/DDR2 memory controllers with ECC support, a 32-bit/66MHz PCI controller, a single 10/100/1000 Ethernet MAC, USB 2.0 (full-speed), multiple TDM serial interfaces for T1/E1/J1/HDLC/ATM, and a system-on-chip local bus. Security-minded peripherals such as SEC 2.0 are not included in this non-encryption variant; teams needing crypto acceleration should evaluate the MPC8360E sister part. The 740-TBGA package exposes all address, data, and peripheral pins to support four DIMM banks and full-width PCI/PCI-X interconnect.
Typical applications include SOHO and enterprise router control planes, DSLAM line card processors, industrial Ethernet gateways, multi-protocol bridge/router modules, and telecom line-interface cards. The 400MHz core is well-matched to routing tables in the 64K-256K-entry range, fast-path forwarding of encrypted VoIP traffic, and protocol-aware QoS scheduling. The integrated DDR1/DDR2 controller eliminates external memory bridge silicon, reducing BOM cost and PCB area, while the TDM interfaces support legacy PSTN interworking alongside modern Ethernet/IP backhaul.
When designing with this device, plan the 740-TBGA layout on a minimum 8-layer PCB with matched-impedance differential pairs for DDR2 and Ethernet. Provide a dedicated 1.2V core supply with at least 1uF of ceramic bypass per power pin, and isolate the analog PLL section with a quiet ferrite-filtered rail. Programming of boot ROM, memory initialization, and pin multiplexing must follow the MPC8360E hardware specifications reference manual; errors here are the most common cause of non-booting boards.
Alternatives de remplacement direct pour MPC8360ZUAGDGA — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MPC8360ZUAGDGA (même facteur de forme et même empreinte) — différant par PCI Interface, Ethernet, Mounting Type, Core Clock Speed, Operating Temperature.
MPC8360EZUAGDGA
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MPC8360ZUAJDGA
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MPC8358ZUAGDGA
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
MPC8360ECVVAGDGA
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MPC8360ZUAGDG
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MPC8360ZUAGDGA Valeurs maximales et caractéristiques électriques
| Processor Type | PowerPC e300 Microprocessor (MPC83xx PowerQUICC II Pro) |
| Core Count | 1 |
| Architecture | 32-Bit Power Architecture |
| Core Clock Speed | 400 MHz |
| Core Voltage | 1.2 V |
| Boîtier / Format | 740-LBGA / 740-TBGA (37.5 x 37.5 mm) |
| Packaging | Tray |
| Température de fonctionnement | 0 C to 105 C |
| Memory Interface | DDR1/DDR2 controller with ECC |
| Ethernet | 1 x 10/100/1000 (Gigabit Ethernet) |
| PCI Interface | 32-bit / 66 MHz PCI |
| USB Interface | USB 2.0 Full-Speed |
| TDM / Serial | Multiple TDM channels (T1/E1/J1/HDLC/ATM) |
| Revision | Revision 2.x TBGA |
| Encryption | Non-encryption variant (no SEC 2.0) |
| Statut RoHS | Compliant |
| Lead Free Status | Lead Free |
Guide de configuration des broches du MPC8360ZUAGDGA 740-lbga / 740-tbga (37.5 x 37.5 mm)
Configuration des broches du MPC8360ZUAGDGA (boîtier 740-lbga / 740-tbga (37.5 x 37.5 mm)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour MPC8360ZUAGDGA.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MPC8360ZUAGDGA convient pour 6 applications: Enterprise Router Control Plane, DSLAM Line Card Processor, Industrial Ethernet Gateway, Multi-Protocol Bridge / Router Module, Telecom Line-Interface Card (VoIP), Secure Access Equipment (Print Server / VPN Endpoint).
Enterprise Router Control Plane
The MPC8360ZUAGDGA's 400MHz e300 core and integrated Gigabit Ethernet MAC deliver deterministic per-packet processing for SOHO and SMB router control planes. Its DDR1/DDR2 controller feeds routing-table lookups efficiently, while the 32-bit/66MHz PCI gives designers a clean path to external Wi-Fi or DSL PHY controllers. Compared with a discrete CPU + glue logic design, integrating the DDR controller and 1GbE MAC into one 740-TBGA part cuts BOM count by 3-4 ICs and saves roughly 30% of PCB area. Pin-compatible upgrade to MPC8360EZUAGDGA adds SEC 2.0 IPsec/SSL acceleration when VPN features are required.
Recommandé
DSLAM Line Card Processor
In DSLAM line cards the MPC8360ZUAGDGA combines multiple TDM/HDLC/ATM interfaces with a 400MHz Power Architecture core to terminate T1/E1/J1 channels and bridge them to uplink Ethernet. The TDM engine handles 32+ timeslots per channel without CPU intervention, freeing the e300 core for traffic shaping and OAM (Operations, Administration, Maintenance) processing. Operating temperature of 0C to 105C matches central-office and outside-plant enclosures. Designers can prototype on this non-encryption part and migrate to the MPC8360EZUAGDGA for line cards that terminate encrypted trunks.
Recommandé
Industrial Ethernet Gateway
The MPC8360ZUAGDGA's USB 2.0 full-speed, Gigabit Ethernet, PCI, and TDM/HDLC mix is ideally suited to industrial gateways bridging PROFINET/EtherCAT-style traffic to legacy fieldbuses. The 400MHz e300 handles real-time protocol translation while the integrated DDR2 controller with ECC protects memory against soft errors common in factory environments. The 0-105C operating range covers enclosed cabinet deployments; the same 740-TBGA footprint across the family simplifies PCB reuse between gateway and control-plane SKUs.
Recommandé
Multi-Protocol Bridge / Router Module
Multi-protocol bridge modules benefit from the MPC8360ZUAGDGA's parallel support for Ethernet, USB, TDM/HDLC, and ATM over a single 400MHz core. Designers can run multiple routing/bridging daemons (e.g. routed IP + bridged Ethernet + ATM PVCs) without external co-processors. The integrated DDR1/DDR2 controller sustains 2-4GB addressable memory, supporting sizeable routing tables for branch-office routing. Pin compatibility with the MPC8360EZUAGDGA lets a single board design serve both encrypted and non-encrypted deployment SKUs.
Recommandé
Telecom Line-Interface Card (VoIP)
VoIP line-interface cards use the MPC8360ZUAGDGA to terminate TDM/HDLC PCM highways while packetizing voice into RTP/IP streams over the integrated Gigabit Ethernet MAC. The 400MHz e300 handles G.711/G.729 codecs in software for low-channel-count line cards, while the TDM engine supports 64+ simultaneous DS0 channels. The SEC 2.0 absence in this non-encryption variant is intentional when SRTP/TLS termination is handled by an external DSP; upgrade to MPC8360EZUAGDGA if you want to offload SRTP onto the host CPU engine.
Recommandé
Secure Access Equipment (Print Server / VPN Endpoint)
Branch-office secure access appliances use the MPC8360ZUAGDGA to aggregate Ethernet, USB peripheral ports, and legacy serial/TDM links behind a single 400MHz e300 core. With 0-105C operation and the integrated 1GbE MAC, the part sits well in fanless branch-office enclosures. Because this variant lacks SEC 2.0 acceleration, firmware-side SSL is suitable for low-throughput TLS terminations; for higher-IPsec-perf designs the pin-compatible MPC8360EZUAGDGA delivers the same peripheral set plus hardware crypto at a modest cost premium.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MPC8360ZUAGDGA — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MPC8360EZUAGDGA | MPC8360ZUAJDGA | MPC8358ZUAGDGA | MPC8360ECVVAGDGA | MPC8360ZUAGDG |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 740-TBGA (37.5x37.5 mm) | 740-TBGA (37.5x37.5) - same | 740-TBGA (37.5x37.5) - same | 740-TBGA (37.5x37.5) - same | 740-TBGA (37.5x37.5) - same | 740-TBGA (37.5x37.5) - same |
| Core Speed | 400 MHz | 400 MHz | 400 MHz | 400 MHz | 400 MHz | 400 MHz |
| Core / Architecture | e300 / Power Architecture 32-bit | e300 / Power Architecture 32-bit | e300 / Power Architecture 32-bit | e300 / Power Architecture 32-bit | e300 / Power Architecture 32-bit | e300 / Power Architecture 32-bit |
| Encryption (SEC 2.0) | No | Yes | No | No | Yes | No |
| Ethernet | 1 x 10/100/1000 | 1 x 10/100/1000 | 1 x 10/100/1000 | 1 x 10/100/1000 | 1 x 10/100/1000 | 1 x 10/100/1000 |
| Memory Interface | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC |
| PCI | 32-bit / 66 MHz | 32-bit / 66 MHz | 32-bit / 66 MHz | 32-bit / 66 MHz | 32-bit / 66 MHz | 32-bit / 66 MHz |
| Operating Temperature | 0 C to 105 C | 0 C to 105 C | 0 C to 105 C (different grade suffix) | 0 C to 105 C | 0 C to 105 C | 0 C to 105 C |
Principaux différenciateurs
- Cleanest pin-compatible upgrade path to an encryption-enabled variant within the same footprint (vs MPC8360EZUAGDGA)
- Different temperature grade suffix while retaining the same 740-TBGA footprint (vs MPC8360ZUAJDGA)
- Reduced peripheral set for cost-sensitive designs in the same package (vs MPC8358ZUAGDGA)
Notes de conception
The 740-TBGA (37.5x37.5 mm) package requires an 8-layer PCB with microvia or HDI stackup to escape the full ball grid. Match-impedance differential pairs must be used for DDR2 (to/from the memory controller) and for the Gigabit Ethernet SERDES nets. Decouple every power pin with at least 1uF of low-ESR ceramic plus a 0.1uF high-frequency bypass in parallel; route short and direct, with vias placed inside the BGA-pad keepout. Estimated: the lowest-cost stackup that meets DDR2 SI requirements is 8-layer 1-oz copper with FR-4 dielectrics.
Provide a dedicated, low-noise 1.2 V rail for the e300 core via a buck regulator with at least 80% efficiency at full load, and isolate the analog PLL supply (AVDD) with a ferrite-filtered branch to suppress core switching noise from coupling into the PLL. Hold the core in reset (HRESET#) until both the 1.2 V core and 3.3 V I/O rails have reached regulation and the reference clock is stable. Estimated: a typical MPC8360ZUAGDGA at 400 MHz with 1GbE active draws in the order of 2-3 W from the core rail, but check the reference manual for the exact figure.
The most common MPC8360ZUAGDGA bring-up issue is incorrect boot ROM memory map or pin multiplexing in the reset configuration words - always cross-check boot_cfg bits against the MPC8360E hardware specifications reference manual. Another frequent pitfall is leaving DDR2 termination weak-pulldowns enabled during read cycles, which causes intermittent data errors above DDR2-667. Do not mix 1.8 V DDR2 and 2.5 V DDR1 straps simultaneously on the same board revision; verify with the datasheet ordering table.
Although the chip's 0-105C operating range is wide, sealed enclosures and stacked TBGA packages trap heat. Estimate the junction temperature rise at roughly 1.5-2 C per watt when the part is soldered to a 4-layer 2-oz copper PCB without airflow; with forced airflow above 1 m/s, this drops to under 1 C/W. Use the e300's internal thermal diode and on-chip temperature sensor to verify production thermal margins. Estimated: a 6-layer inner-ground PCB improves theta_JA by 20-30% versus 4-layer.
Informations de conformité
RoHS and lead-free per datasheet and distributor listings (DigiKey/Heisener). AEC-Q100 not applicable for this networking MPU. Conflict-mineral statement per NXP corporate policy.
