PIC10F202-I/MC - 8-Bit 4MHz 768B Flash MCU | Microchip
Référence : PIC10F202-I/MC ✓ ActifPIC10F202-I/MC Présentation
A microcontroller is a programmable semiconductor that combines a processor core, program memory, data memory, and peripherals on one integrated circuit. The PIC10F202 belongs to the PIC10 family of 8-bit RISC microcontrollers. Its compact architecture supports basic control, timing, signal-generation, and simple sensor-processing functions where a larger processor and more memory would add unnecessary cost or board area.
The device uses a RISC instruction set with 33 single-word, single-cycle instructions. Most instructions execute in one cycle at a 4 MHz instruction rate, while program branches require two cycles. Its 768-byte Flash memory is organized as 512 words of 12-bit program storage, and its 24-byte SRAM provides working memory for stack and runtime variables. Four general-purpose I/O pins allow the device to interface with switches, indicators, sensors, and external control logic.
PIC10F202-I/MC is programmed through dedicated programming interfaces and can be supported by Microchip development tools. Because the device is Flash-based, firmware can be rewritten during development and later programmed into production units without relying on one-time-programmable memory. The “I” ordering suffix identifies the industrial-temperature product, while “/MC” identifies the 8-DFN package configuration.
Typical applications include compact household controls, simple motor or relay sequencing, push-button interfaces, LED status indicators, low-cost sensing modules, and autonomous electronics that require deterministic single-cycle instruction execution. Its 2 mm by 3 mm footprint is especially useful when board space is constrained and the required control logic does not justify a higher-capacity MCU.
PCB design should preserve the manufacturer's recommended pad geometry, exposed-pad soldering requirements, and decoupling arrangement. Confirm the pin assignments, programming connections, and operating limits in the manufacturer datasheet before layout release, and validate the completed board at the lowest intended supply voltage and highest expected ambient temperature.
Alternatives de remplacement direct pour PIC10F202-I/MC — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC10F202-I/MC (même facteur de forme et même empreinte) — différant par Package, Timers, Core Architecture, Watchdog Timer, Instruction Set.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesPIC10F202-I/MC Valeurs maximales et caractéristiques électriques
| Microcontroller Type | 8-Bit RISC Flash Microcontroller |
| Fréquence d'horloge maximale | 4 MHz |
| Program Memory | 768 bytes Flash (512 x 12 bits) |
| Data Memory | 24 bytes SRAM |
| General-Purpose I/O | 4 pins |
| Architecture | PIC10 8-bit RISC |
| Instruction Set | 33 single-word, single-cycle instructions |
| Normal Instruction Cycle | 1 cycle at 4 MHz (0.25 us) |
| Program Branch Cycle | 2 cycles |
| Supply Voltage Range | 2.5 V to 5 V |
| Boîtier | 8-DFN, 2 x 3 mm |
| Type de montage | Surface Mount |
| Temperature Grade | Industrial grade (-40C to +85C) |
| Programming Memory Type | Flash |
| Packaging Type | Tube |
Guide de configuration des broches du PIC10F202-I/MC 8-dfn, 2 x 3 mm
Configuration des broches du PIC10F202-I/MC (boîtier 8-dfn, 2 x 3 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour PIC10F202-I/MC.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
PIC10F202-I/MC convient pour 6 applications: Compact Household Appliance Control, LED Status and Button Interface, Simple Relay and Switch Sequencing, Low-Cost Sensor Conditioning Module, Programmable Timer and Pulse Controller, Compact Industrial Control Module.
Compact Household Appliance Control
PIC10F202-I/MC fits small appliance controllers that require deterministic logic, limited I/O, and minimal board area. The 4 MHz RISC core executes most instructions in one 0.25 microsecond cycle, while 768 bytes of Flash provides storage for a compact state machine. Four I/O pins can operate relays, buttons, indicators, or discrete sensors. Its 8-DFN 2 x 3 mm package reduces PCB footprint, although designers must follow the exposed-pad soldering and decoupling guidance in the manufacturer datasheet.
Recommandé
LED Status and Button Interface
PIC10F202-I/MC can consolidate button sensing and LED indication into a small embedded module. Its four I/O pins are sufficient for a limited keypad or switch matrix and status indicators, while the single-cycle instruction model simplifies debounce and display-update timing. With 24 bytes of RAM, the firmware should avoid deep call nesting and unnecessary buffering. The compact 8-DFN outline also supports integration into tightly spaced user-interface assemblies.
Recommandé
Simple Relay and Switch Sequencing
PIC10F202-I/MC is suitable for basic relay, solenoid, or switch-sequencing modules where a small deterministic program is enough. Its four I/O pins can share a control port with input switches and output drivers, and program branches of two cycles provide a straightforward timing model for interlocks and delays. Designers must check output-driver current limits and use suitable transistor or driver circuits for loads above the MCU's direct output capability.
Recommandé
Low-Cost Sensor Conditioning Module
PIC10F202-I/MC can act as the local controller in a small sensing module that reads a limited set of discrete inputs and applies thresholding or filtering. The 24-byte RAM is suitable for compact working variables, while the 512-word program area supports a focused control routine rather than a complex application. Its low-voltage operation from 2.5 V to 5 V fits many sensor and energy-limited designs. Analog accuracy and sensor timing must be evaluated separately from the MCU's digital processing capability.
Recommandé
Programmable Timer and Pulse Controller
PIC10F202-I/MC is practical for small programmable timers, pulse generators, and periodic switching modules. At its 4 MHz maximum clock, most instructions complete in one cycle, while branches take two, enabling compact event sequencing without a large real-time processor. Four I/O pins allow timer outputs to coexist with configuration switches. The design should account for the fixed 24-byte RAM and use the manufacturer's timer and oscillator characteristics to establish timing accuracy.
Recommandé
Compact Industrial Control Module
PIC10F202-I/MC supports compact industrial control modules that require an industrial-temperature MCU, Flash-reprogrammable firmware, and a very small footprint. The -40C to +85C ordering grade is suitable for controlled equipment enclosures, while the 2.5 V to 5 V supply range supports common embedded rails. Four I/O pins keep the device appropriate for simple actuator and sensor coordination. Production designs should still validate power-supply tolerance, noise immunity, and thermal performance at the enclosure's worst-case temperature.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC10F202-I/MC — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Package | 8-DFN (2 x 3 mm) |
| Brand | Microchip Technology |
| CPU Architecture | 8-bit RISC |
| Maximum Clock Frequency | 4 MHz |
| Program Memory | 768 bytes Flash (512 x 12 bits) |
| Data Memory | 24 bytes SRAM |
| General-Purpose I/O | 4 pins |
| Supply Voltage Range | 2.5 V to 5 V |
| Temperature Grade | Industrial: -40C to +85C |
| Instruction Set | 33 single-word, single-cycle instructions; branches take two cycles |
Notes de conception
Use the land pattern and exposed-pad dimensions defined by the Microchip package drawing rather than constructing a generic 8-DFN footprint from the body size alone. The exposed pad is part of the thermal and electrical design, so the PCB solder mask, paste stencil, and assembly profile should follow the manufacturer's recommendations. Confirm pin-1 orientation against the package drawing before releasing Gerber files.
Plan the 2.5 V to 5 V supply rail so it remains within the device's operating range during startup, reset, and maximum load. Place the required bypass capacitor close to the power and ground connections and keep the return path short. Use the electrical-characteristics tables to select the capacitor value and voltage rating for the actual clock, I/O, and temperature conditions.
Do not assume that four I/O pins can directly drive relays, motors, lamps, or other inductive loads. Check each pin's output-current and voltage limits, then add suitable transistor or driver circuitry with protection for inductive transients. Also reserve pins required by programming and debugging access so the finished board can be programmed without a costly rework.
Keep the 8-DFN exposed-pad solder process consistent with the package's thermal requirements and the PCB assembly method. Inspect the joints for voiding under the thermal pad because poor voiding can reduce heat transfer. Keep sensitive analog or high-impedance nodes away from programming-interface traces and switching-node connections when the MCU is mounted in a mixed-signal control assembly.
The small DFN outline limits the amount of copper available for heat spreading, so estimate the worst-case internal dissipation from the selected clock rate, supply voltage, I/O loading, and ambient temperature. Place the device near an effective ground plane and avoid enclosing it in a thermally isolated section of the board. Validate the final assembly at maximum expected load and temperature rather than relying only on nominal calculations.
Informations de conformité
The listed industrial-temperature ordering code does not establish AEC-Q100 qualification. Compliance status requires confirmation from the manufacturer product or material declaration.