Microchip Technology

PIC10F202-I/MC - 8-Bit 4MHz 768B Flash MCU | Microchip

MPN: PIC10F202-I/MC ✓ Active
2.5 V to 5 V Vdss 8-DFN, 2 x 3 mm Package 4 MHz Speed 768 bytes Flash (512 x 12 bits) Memory
MOQ: 1 |

PIC10F202-I/MC Overview

The Microchip Technology PIC10F202-I/MC is a low-cost, 8-bit, fully static, Flash-based CMOS microcontroller operating at up to 4 MHz, with 768 bytes of program Flash and 24 bytes of data RAM. It is packaged in an 8-DFN surface-mount package measuring 2 mm by 3 mm and is designed for compact embedded-control applications.

A microcontroller is a programmable semiconductor that combines a processor core, program memory, data memory, and peripherals on one integrated circuit. The PIC10F202 belongs to the PIC10 family of 8-bit RISC microcontrollers. Its compact architecture supports basic control, timing, signal-generation, and simple sensor-processing functions where a larger processor and more memory would add unnecessary cost or board area.

The device uses a RISC instruction set with 33 single-word, single-cycle instructions. Most instructions execute in one cycle at a 4 MHz instruction rate, while program branches require two cycles. Its 768-byte Flash memory is organized as 512 words of 12-bit program storage, and its 24-byte SRAM provides working memory for stack and runtime variables. Four general-purpose I/O pins allow the device to interface with switches, indicators, sensors, and external control logic.

PIC10F202-I/MC is programmed through dedicated programming interfaces and can be supported by Microchip development tools. Because the device is Flash-based, firmware can be rewritten during development and later programmed into production units without relying on one-time-programmable memory. The “I” ordering suffix identifies the industrial-temperature product, while “/MC” identifies the 8-DFN package configuration.

Typical applications include compact household controls, simple motor or relay sequencing, push-button interfaces, LED status indicators, low-cost sensing modules, and autonomous electronics that require deterministic single-cycle instruction execution. Its 2 mm by 3 mm footprint is especially useful when board space is constrained and the required control logic does not justify a higher-capacity MCU.

PCB design should preserve the manufacturer's recommended pad geometry, exposed-pad soldering requirements, and decoupling arrangement. Confirm the pin assignments, programming connections, and operating limits in the manufacturer datasheet before layout release, and validate the completed board at the lowest intended supply voltage and highest expected ambient temperature.

Drop-in alternatives for PIC10F202-I/MC — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with PIC10F202-I/MC (same form factor and footprint) — differing in Package, Timers, Core Architecture, Watchdog Timer, Instruction Set.

Microchip Technology
Package: 8-pin DFN (2 mm x 3 mm)
Timers: 1 x 8-bit
Core Architecture: PIC 8-bit RISC
Microchip Technology
Package: 8-VFDFN Exposed Pad (MC)
Timers: TMR0 (8-bit with 8-bit prescaler)
Core Architecture: 8-bit PIC RISC
Microchip Technology
Package: 8-pin DFN (2 mm x 3 mm), "MC"
Timers: 1 x 8-bit (TMR0) with programmable prescaler
Core Architecture: 8-bit PIC RISC (Harvard)
Microchip Technology
Package: 8-pin DFN (2x3 mm), designated MC
Timers: 1 x 8-bit (TMR0 with prescaler)
Watchdog Timer: Yes, with on-chip RC oscillator

No drop-in alternatives available for this product.

Request Alternatives

PIC10F202-I/MC Maximum Ratings & Electrical Characteristics

Microcontroller Type 8-Bit RISC Flash Microcontroller
Maximum Clock Frequency 4 MHz
Program Memory 768 bytes Flash (512 x 12 bits)
Data Memory 24 bytes SRAM
General-Purpose I/O 4 pins
Architecture PIC10 8-bit RISC
Instruction Set 33 single-word, single-cycle instructions
Normal Instruction Cycle 1 cycle at 4 MHz (0.25 us)
Program Branch Cycle 2 cycles
Supply Voltage Range 2.5 V to 5 V
Package 8-DFN, 2 x 3 mm
Mounting Type Surface Mount
Temperature Grade Industrial grade (-40C to +85C)
Programming Memory Type Flash
Packaging Type Tube

PIC10F202-I/MC 8-dfn, 2 x 3 mm Pin Configuration Guide

Pin configuration for PIC10F202-I/MC (8-dfn, 2 x 3 mm package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.

8-dfn, 2 x 3 mm package pinout diagram for PIC10F202-I/MC

No detailed pinout data available for PIC10F202-I/MC.

Refer to the datasheet for full pin configuration.

Typical Applications

PIC10F202-I/MC is suitable for 6 applications: Compact Household Appliance Control, LED Status and Button Interface, Simple Relay and Switch Sequencing, Low-Cost Sensor Conditioning Module, Programmable Timer and Pulse Controller, Compact Industrial Control Module.

🏠

Compact Household Appliance Control

PIC10F202-I/MC fits small appliance controllers that require deterministic logic, limited I/O, and minimal board area. The 4 MHz RISC core executes most instructions in one 0.25 microsecond cycle, while 768 bytes of Flash provides storage for a compact state machine. Four I/O pins can operate relays, buttons, indicators, or discrete sensors. Its 8-DFN 2 x 3 mm package reduces PCB footprint, although designers must follow the exposed-pad soldering and decoupling guidance in the manufacturer datasheet.

💡

LED Status and Button Interface

PIC10F202-I/MC can consolidate button sensing and LED indication into a small embedded module. Its four I/O pins are sufficient for a limited keypad or switch matrix and status indicators, while the single-cycle instruction model simplifies debounce and display-update timing. With 24 bytes of RAM, the firmware should avoid deep call nesting and unnecessary buffering. The compact 8-DFN outline also supports integration into tightly spaced user-interface assemblies.

⚡

Simple Relay and Switch Sequencing

PIC10F202-I/MC is suitable for basic relay, solenoid, or switch-sequencing modules where a small deterministic program is enough. Its four I/O pins can share a control port with input switches and output drivers, and program branches of two cycles provide a straightforward timing model for interlocks and delays. Designers must check output-driver current limits and use suitable transistor or driver circuits for loads above the MCU's direct output capability.

🧩

Low-Cost Sensor Conditioning Module

PIC10F202-I/MC can act as the local controller in a small sensing module that reads a limited set of discrete inputs and applies thresholding or filtering. The 24-byte RAM is suitable for compact working variables, while the 512-word program area supports a focused control routine rather than a complex application. Its low-voltage operation from 2.5 V to 5 V fits many sensor and energy-limited designs. Analog accuracy and sensor timing must be evaluated separately from the MCU's digital processing capability.

⏱️

Programmable Timer and Pulse Controller

PIC10F202-I/MC is practical for small programmable timers, pulse generators, and periodic switching modules. At its 4 MHz maximum clock, most instructions complete in one cycle, while branches take two, enabling compact event sequencing without a large real-time processor. Four I/O pins allow timer outputs to coexist with configuration switches. The design should account for the fixed 24-byte RAM and use the manufacturer's timer and oscillator characteristics to establish timing accuracy.

🏭

Compact Industrial Control Module

PIC10F202-I/MC supports compact industrial control modules that require an industrial-temperature MCU, Flash-reprogrammable firmware, and a very small footprint. The -40C to +85C ordering grade is suitable for controlled equipment enclosures, while the 2.5 V to 5 V supply range supports common embedded rails. Four I/O pins keep the device appropriate for simple actuator and sensor coordination. Production designs should still validate power-supply tolerance, noise immunity, and thermal performance at the enclosure's worst-case temperature.

Recommended Products Summary

PIC10F202 Base device family Used in: Compact Household Appliance Control, LED Status and Button Interface, Simple Relay and Switch Sequencing, Low-Cost Sensor Conditioning Module, Programmable Timer and Pulse Controller, Compact Industrial Control Module PIC10F200 Related PIC10-family controller Used in: Compact Household Appliance Control, Simple Relay and Switch Sequencing, Programmable Timer and Pulse Controller PIC10F202T-I/MC Equivalent controller in tape-and-reel packaging Used in: LED Status and Button Interface, Low-Cost Sensor Conditioning Module, Compact Industrial Control Module
What are the key specifications of PIC10F202-I/MC that engineers should know?
PIC10F202-I/MC is an 8-bit Flash microcontroller rated up to 4 MHz with 768 bytes of program memory, 24 bytes of SRAM, and four I/O pins. According to the Microchip PIC10F202 product information, its RISC core provides 33 single-word, single-cycle instructions, while program branches take two cycles. The device operates from 2.5 V to 5 V and is offered in an 8-DFN package measuring 2 mm by 3 mm.
Where can I download the PIC10F202-I/MC datasheet PDF?
The official PIC10F202 datasheet is available through the Microchip PIC10F202 product page at https://www.microchip.com/en-us/product/PIC10F202. The PIC10F202-I/MC ordering code identifies the industrial-temperature, 8-DFN configuration. Use the pin-description table, electrical-characteristics tables, and package drawings in that manufacturer datasheet when creating the PCB footprint and power circuit.
Where can I find the PIC10F202 pinout?
The PIC10F202 pinout is defined in the pin-description table of the manufacturer datasheet linked from the official PIC10F202 product page. The PIC10F202-I/MC uses an 8-DFN package with an exposed thermal pad, so the land pattern must include the exposed-pad geometry and paste stencil specified by Microchip. Confirm every programming, power, ground, and I/O connection before fabrication.
How do I program a PIC10F202 microcontroller?
PIC10F202 devices are programmed through the dedicated programming interface described in the manufacturer programming documentation. The Flash-based architecture permits firmware to be rewritten during development and programmed into production units. The PIC10F202-I/MC operates with a 33-instruction RISC core at up to 4 MHz, so most instructions execute in one 0.25 microsecond cycle at the maximum clock frequency.
What is the PIC10F202-I/MC used for?
PIC10F202-I/MC is used for compact embedded-control tasks such as switch and button interfaces, LED indicators, simple sensor conditioning, relay sequencing, and small appliance controls. Its four I/O pins, 24-byte SRAM, and 768-byte Flash footprint are sufficient for straightforward control logic. The 2 mm by 3 mm 8-DFN package helps reduce board area when the application does not require a larger MCU or extensive peripherals.
Is PIC10F202-I/MC suitable for industrial control applications?
PIC10F202-I/MC is the industrial-temperature ordering option and operates across the -40C to +85C temperature range when operated within the manufacturer's electrical limits. Its 2.5 V to 5 V supply range supports common embedded control rails. Industrial suitability still depends on the enclosure, power quality, electromagnetic environment, and the final system's fault-tolerance requirements.
How much Flash memory and RAM does PIC10F202-I/MC have?
PIC10F202-I/MC contains 768 bytes of Flash program memory organized as 512 words of 12 bits and 24 bytes of data RAM. The program-memory size is suitable for compact control routines, while the RAM supports stack operations and a limited set of working variables. Designers should check application size and RAM demand against these fixed capacities before selecting the MCU.
What is the difference between PIC10F202 and PIC10F202-I/MC?
PIC10F202 identifies the base Microchip device family, while PIC10F202-I/MC is a specific orderable configuration with an industrial temperature grade and an 8-DFN package. The listed electrical identity is an 8-bit, 4 MHz MCU with 768 bytes of Flash and 24 bytes of RAM. Review the manufacturer's ordering table when confirming the exact package and temperature grade for a new assembly.
What can replace PIC10F202-I/MC?
A direct replacement should match the 8-DFN footprint, pin assignments, 768-byte Flash organization, 24-byte RAM, 4 MHz operation, supply range, and programming interface. No independently confirmed cross-manufacturer drop-in replacement was identified for this exact orderable configuration. PIC10F202T-I/MC is the same device in tape-and-reel packaging, but it is not a different functional substitute.
Is PIC10F202-I/MC the same as PIC10F202T-I/MC?
PIC10F202-I/MC and PIC10F202T-I/MC refer to the same 8-DFN PIC10F202 electrical configuration, with the ordering suffixes distinguishing delivery packaging. The listed characteristics are 8-bit operation, 4 MHz maximum frequency, 768 bytes of Flash, 24 bytes of RAM, and four I/O pins. The /MC version is listed in tube packaging, while the T/I/MC version uses tape-and-reel packaging.
When should I choose PIC10F202-I/MC over a larger 8-bit microcontroller?
Choose PIC10F202-I/MC when the control task fits within 512 program words and 24 bytes of RAM, and when four I/O pins are sufficient. Its 4 MHz single-cycle instruction execution is useful for simple timing and state-machine logic. Move to a larger MCU when firmware growth, peripheral requirements, RAM usage, or I/O count exceeds the capacity of this compact device.
Is PIC10F202-I/MC suitable for a low-voltage embedded product?
PIC10F202-I/MC can operate from 2.5 V to 5 V, making it suitable for embedded products that use a regulated low-voltage rail. The design must account for MCU current, input thresholds, output-driver limits, and the voltage required by attached peripherals. Confirm startup, brownout, and operating behavior against the electrical-characteristics tables for the exact supply condition.
How much current does PIC10F202-I/MC consume?
PIC10F202-I/MC operating current depends on supply voltage, clock configuration, active versus sleep mode, and the states of its I/O pins. The listed operating range is 2.5 V to 5 V, but a single current value cannot be stated without those operating conditions. Use the manufacturer datasheet's DC and sleep-mode characteristic tables for battery-life and power-budget calculations.
What are the advantages of the PIC10F202's single-cycle RISC instructions?
The PIC10F202 executes most of its 33 single-word instructions in one cycle, producing a simple and predictable timing model at the 4 MHz maximum frequency. According to the Microchip product information, program branches take two cycles. This regular execution model can simplify timing analysis in small state machines, although interrupt latency and peripheral timing still require normal design checks.
Where can I buy PIC10F202-I/MC and what is the current lead time?
Use the Request a Quote form on this page to request PIC10F202-I/MC availability, current lead time, minimum order quantity, and shipment options. The request should identify the exact 8-DFN ordering code and tube packaging requirement. The distributor listing confirms the part is cataloged, but a current committed delivery date must be confirmed for the requested quantity.
What is the price of PIC10F202-I/MC?
The current commercial terms for PIC10F202-I/MC are provided through the Request a Quote form on this page. Submit the required quantity, packaging preference, target delivery location, and production schedule for a current quotation. The structured listing does not publish a stable fixed-price offer for this exact orderable configuration.
Is PIC10F202-I/MC in stock?
PIC10F202-I/MC inventory should be confirmed through the Request a Quote form on this page because stock and allocation can change with order volume and production schedules. Include the exact MPN, requested quantity, and tube packaging requirement in the request. The part is listed as available by authorized distribution channels, but a current lot-specific commitment is required.
What is the best drop-in replacement for PIC10F202-I/MC?
The best drop-in replacement for PIC10F202-I/MC is a device with the same 8-DFN pin assignment, 2 x 3 mm footprint, 768-byte Flash organization, 24-byte SRAM, four I/O pins, 4 MHz maximum clock, and compatible programming interface. No distinct cross-brand drop-in part was confirmed. PIC10F202T-I/MC matches the device electrically but changes the packaging format, so firmware and hardware remain compatible.

Engineering reference data for PIC10F202-I/MC — comparison, design guidance, and compliance information.

Selection Guide

Choose PIC10F202-I/MC when a compact, Flash-programmable 8-bit MCU is sufficient for simple control logic, four I/O pins, 24 bytes of RAM, and 512 program words. Its 4 MHz single-cycle RISC execution provides deterministic behavior in small state machines, while the 8-DFN package reduces board area. Consider a larger MCU when firmware size, RAM demand, peripheral count, or pin count exceeds this device's capacity. No distinct cross-brand drop-in alternative was confirmed. PIC10F202T-I/MC is electrically the same device in tape-and-reel packaging and can be used for automated production assembly, but it is not a different silicon choice. Before ordering, confirm the exact package drawing, exposed-pad treatment, programming connector, supply requirements, and delivery format against the manufacturer's documentation.

Comparison with Alternatives

Parameter This Product
Package 8-DFN (2 x 3 mm)
Brand Microchip Technology
CPU Architecture 8-bit RISC
Maximum Clock Frequency 4 MHz
Program Memory 768 bytes Flash (512 x 12 bits)
Data Memory 24 bytes SRAM
General-Purpose I/O 4 pins
Supply Voltage Range 2.5 V to 5 V
Temperature Grade Industrial: -40C to +85C
Instruction Set 33 single-word, single-cycle instructions; branches take two cycles

Design Notes

Use the land pattern and exposed-pad dimensions defined by the Microchip package drawing rather than constructing a generic 8-DFN footprint from the body size alone. The exposed pad is part of the thermal and electrical design, so the PCB solder mask, paste stencil, and assembly profile should follow the manufacturer's recommendations. Confirm pin-1 orientation against the package drawing before releasing Gerber files.

Plan the 2.5 V to 5 V supply rail so it remains within the device's operating range during startup, reset, and maximum load. Place the required bypass capacitor close to the power and ground connections and keep the return path short. Use the electrical-characteristics tables to select the capacitor value and voltage rating for the actual clock, I/O, and temperature conditions.

Do not assume that four I/O pins can directly drive relays, motors, lamps, or other inductive loads. Check each pin's output-current and voltage limits, then add suitable transistor or driver circuitry with protection for inductive transients. Also reserve pins required by programming and debugging access so the finished board can be programmed without a costly rework.

Keep the 8-DFN exposed-pad solder process consistent with the package's thermal requirements and the PCB assembly method. Inspect the joints for voiding under the thermal pad because poor voiding can reduce heat transfer. Keep sensitive analog or high-impedance nodes away from programming-interface traces and switching-node connections when the MCU is mounted in a mixed-signal control assembly.

The small DFN outline limits the amount of copper available for heat spreading, so estimate the worst-case internal dissipation from the selected clock rate, supply voltage, I/O loading, and ambient temperature. Place the device near an effective ground plane and avoid enclosing it in a thermally isolated section of the board. Validate the final assembly at maximum expected load and temperature rather than relying only on nominal calculations.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The listed industrial-temperature ordering code does not establish AEC-Q100 qualification. Compliance status requires confirmation from the manufacturer product or material declaration.

Related Searches

pic10f202 datasheet pic10f202 pinout pic10f202 programming PIC10F202-I/MC datasheet PIC10F202-I/MC pinout PIC10F202-I/MC 8-DFN PIC10F202-I/MC specifications PIC10F202-I/MC equivalent PIC10F202-I/MC replacement PIC10F202 8-bit microcontroller PIC10F202 application circuit PIC10F202-I/MC price PIC10F202-I/MC stock Microchip PIC10F202-I/MC

Related Components & Terms

Microchip Technology PIC10F202-I/MC PIC10F202 PIC10F202T-I/MC PIC10F200 PIC10 microcontroller MCU 8-bit RISC Flash memory CMOS 4 MHz 768-byte Flash 24-byte SRAM four I/O pins 8-DFN QFN family surface-mount package 2.5 V to 5 V industrial temperature grade single-cycle instruction embedded control low-voltage control
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details