PIC10F202-I/MC - 8-Bit 4MHz 768B Flash MCU | Microchip
부품 번호: PIC10F202-I/MC ✓ 활성PIC10F202-I/MC 개요
A microcontroller is a programmable semiconductor that combines a processor core, program memory, data memory, and peripherals on one integrated circuit. The PIC10F202 belongs to the PIC10 family of 8-bit RISC microcontrollers. Its compact architecture supports basic control, timing, signal-generation, and simple sensor-processing functions where a larger processor and more memory would add unnecessary cost or board area.
The device uses a RISC instruction set with 33 single-word, single-cycle instructions. Most instructions execute in one cycle at a 4 MHz instruction rate, while program branches require two cycles. Its 768-byte Flash memory is organized as 512 words of 12-bit program storage, and its 24-byte SRAM provides working memory for stack and runtime variables. Four general-purpose I/O pins allow the device to interface with switches, indicators, sensors, and external control logic.
PIC10F202-I/MC is programmed through dedicated programming interfaces and can be supported by Microchip development tools. Because the device is Flash-based, firmware can be rewritten during development and later programmed into production units without relying on one-time-programmable memory. The “I” ordering suffix identifies the industrial-temperature product, while “/MC” identifies the 8-DFN package configuration.
Typical applications include compact household controls, simple motor or relay sequencing, push-button interfaces, LED status indicators, low-cost sensing modules, and autonomous electronics that require deterministic single-cycle instruction execution. Its 2 mm by 3 mm footprint is especially useful when board space is constrained and the required control logic does not justify a higher-capacity MCU.
PCB design should preserve the manufacturer's recommended pad geometry, exposed-pad soldering requirements, and decoupling arrangement. Confirm the pin assignments, programming connections, and operating limits in the manufacturer datasheet before layout release, and validate the completed board at the lowest intended supply voltage and highest expected ambient temperature.
드롭인 대체품: PIC10F202-I/MC — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PIC10F202-I/MC (동일 폼 팩터 및 풋프린트) — 차이점: Package, Timers, Core Architecture, Watchdog Timer, Instruction Set.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청PIC10F202-I/MC 최대 정격 & 전기적 특성
| Microcontroller Type | 8-Bit RISC Flash Microcontroller |
| 최대 클록 주파수 | 4 MHz |
| Program Memory | 768 bytes Flash (512 x 12 bits) |
| Data Memory | 24 bytes SRAM |
| General-Purpose I/O | 4 pins |
| Architecture | PIC10 8-bit RISC |
| Instruction Set | 33 single-word, single-cycle instructions |
| Normal Instruction Cycle | 1 cycle at 4 MHz (0.25 us) |
| Program Branch Cycle | 2 cycles |
| Supply Voltage Range | 2.5 V to 5 V |
| 패키지 | 8-DFN, 2 x 3 mm |
| 실장 유형 | Surface Mount |
| Temperature Grade | Industrial grade (-40C to +85C) |
| Programming Memory Type | Flash |
| Packaging Type | Tube |
PIC10F202-I/MC 8-dfn, 2 x 3 mm 핀 구성 가이드
PIC10F202-I/MC(8-dfn, 2 x 3 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: PIC10F202-I/MC.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
PIC10F202-I/MC 적합 용도: 6 애플리케이션s: Compact Household Appliance Control, LED Status and Button Interface, Simple Relay and Switch Sequencing, Low-Cost Sensor Conditioning Module, Programmable Timer and Pulse Controller, Compact Industrial Control Module.
Compact Household Appliance Control
PIC10F202-I/MC fits small appliance controllers that require deterministic logic, limited I/O, and minimal board area. The 4 MHz RISC core executes most instructions in one 0.25 microsecond cycle, while 768 bytes of Flash provides storage for a compact state machine. Four I/O pins can operate relays, buttons, indicators, or discrete sensors. Its 8-DFN 2 x 3 mm package reduces PCB footprint, although designers must follow the exposed-pad soldering and decoupling guidance in the manufacturer datasheet.
추천
LED Status and Button Interface
PIC10F202-I/MC can consolidate button sensing and LED indication into a small embedded module. Its four I/O pins are sufficient for a limited keypad or switch matrix and status indicators, while the single-cycle instruction model simplifies debounce and display-update timing. With 24 bytes of RAM, the firmware should avoid deep call nesting and unnecessary buffering. The compact 8-DFN outline also supports integration into tightly spaced user-interface assemblies.
추천
Simple Relay and Switch Sequencing
PIC10F202-I/MC is suitable for basic relay, solenoid, or switch-sequencing modules where a small deterministic program is enough. Its four I/O pins can share a control port with input switches and output drivers, and program branches of two cycles provide a straightforward timing model for interlocks and delays. Designers must check output-driver current limits and use suitable transistor or driver circuits for loads above the MCU's direct output capability.
추천
Low-Cost Sensor Conditioning Module
PIC10F202-I/MC can act as the local controller in a small sensing module that reads a limited set of discrete inputs and applies thresholding or filtering. The 24-byte RAM is suitable for compact working variables, while the 512-word program area supports a focused control routine rather than a complex application. Its low-voltage operation from 2.5 V to 5 V fits many sensor and energy-limited designs. Analog accuracy and sensor timing must be evaluated separately from the MCU's digital processing capability.
추천
Programmable Timer and Pulse Controller
PIC10F202-I/MC is practical for small programmable timers, pulse generators, and periodic switching modules. At its 4 MHz maximum clock, most instructions complete in one cycle, while branches take two, enabling compact event sequencing without a large real-time processor. Four I/O pins allow timer outputs to coexist with configuration switches. The design should account for the fixed 24-byte RAM and use the manufacturer's timer and oscillator characteristics to establish timing accuracy.
추천
Compact Industrial Control Module
PIC10F202-I/MC supports compact industrial control modules that require an industrial-temperature MCU, Flash-reprogrammable firmware, and a very small footprint. The -40C to +85C ordering grade is suitable for controlled equipment enclosures, while the 2.5 V to 5 V supply range supports common embedded rails. Four I/O pins keep the device appropriate for simple actuator and sensor coordination. Production designs should still validate power-supply tolerance, noise immunity, and thermal performance at the enclosure's worst-case temperature.
추천
추천 제품 요약
엔지니어링 참조 데이터: PIC10F202-I/MC — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Package | 8-DFN (2 x 3 mm) |
| Brand | Microchip Technology |
| CPU Architecture | 8-bit RISC |
| Maximum Clock Frequency | 4 MHz |
| Program Memory | 768 bytes Flash (512 x 12 bits) |
| Data Memory | 24 bytes SRAM |
| General-Purpose I/O | 4 pins |
| Supply Voltage Range | 2.5 V to 5 V |
| Temperature Grade | Industrial: -40C to +85C |
| Instruction Set | 33 single-word, single-cycle instructions; branches take two cycles |
설계 노트
Use the land pattern and exposed-pad dimensions defined by the Microchip package drawing rather than constructing a generic 8-DFN footprint from the body size alone. The exposed pad is part of the thermal and electrical design, so the PCB solder mask, paste stencil, and assembly profile should follow the manufacturer's recommendations. Confirm pin-1 orientation against the package drawing before releasing Gerber files.
Plan the 2.5 V to 5 V supply rail so it remains within the device's operating range during startup, reset, and maximum load. Place the required bypass capacitor close to the power and ground connections and keep the return path short. Use the electrical-characteristics tables to select the capacitor value and voltage rating for the actual clock, I/O, and temperature conditions.
Do not assume that four I/O pins can directly drive relays, motors, lamps, or other inductive loads. Check each pin's output-current and voltage limits, then add suitable transistor or driver circuitry with protection for inductive transients. Also reserve pins required by programming and debugging access so the finished board can be programmed without a costly rework.
Keep the 8-DFN exposed-pad solder process consistent with the package's thermal requirements and the PCB assembly method. Inspect the joints for voiding under the thermal pad because poor voiding can reduce heat transfer. Keep sensitive analog or high-impedance nodes away from programming-interface traces and switching-node connections when the MCU is mounted in a mixed-signal control assembly.
The small DFN outline limits the amount of copper available for heat spreading, so estimate the worst-case internal dissipation from the selected clock rate, supply voltage, I/O loading, and ambient temperature. Place the device near an effective ground plane and avoid enclosing it in a thermally isolated section of the board. Validate the final assembly at maximum expected load and temperature rather than relying only on nominal calculations.
규정 준수 정보
The listed industrial-temperature ordering code does not establish AEC-Q100 qualification. Compliance status requires confirmation from the manufacturer product or material declaration.