PIC32MX350F128H-I/MR - 32-bit MCU, 100MHz, 128KB Flash | Microchip
Référence : PIC32MX350F128H-I/MR ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $4.86 | $4,86 |
| 10 | $4.32 | $43,20 |
| 100 | $3.78 | $378,00 |
| 500 | $3.36 | $1 680,00 |
| 1 000 | $2.98 | $2 980,00 |
PIC32MX350F128H-I/MR Présentation
A 32-bit microcontroller (MCU) is a programmable system-on-chip that combines a high-performance processor core, Flash program memory, SRAM data memory, and a rich set of digital and analog peripherals. Within the broader hierarchy, PIC32MX MCUs sit between the 8-bit PIC16/PIC18 families and the higher-performance PIC32MZ family, and are categorized as application microcontrollers within Microchip's "power management IC" and "embedded control" taxonomy. The 32-bit MIPS core delivers up to 150 DMIPS while remaining code-compatible with the MPLAB X IDE and Harmony framework.
Key differentiating features of the PIC32MX350F128H-I/MR include Peripheral Pin Select (PPS), which allows most digital peripherals to be routed to nearly any I/O pin, dramatically easing PCB layout. Two I2S/SPI modules enable audio codec interfacing, the PMP module supports graphics LCDs, and the integrated CTMU provides reliable capacitive touch sensing without external circuitry. Five 16-bit timers, five input capture and five output compare modules support advanced motor control and waveform generation.
Architecture-wise, the PIC32MX3/4 uses a 5-stage pipeline MIPS32 M4K core with hardware multiply/divide, single-cycle Flash access via a 128-bit-wide bus, and a prefetch module that masks Flash latency to deliver near-zero-wait-state performance. The device includes a 10-bit 1 Msps ADC with up to 28 channels, two analog comparators, and a brown-out-reset (BOR) circuit for robust industrial operation.
Typical applications include USB-enabled consumer and industrial controllers, audio interfaces with external I2S codecs, graphics HMI boards driving small TFT LCDs via PMP, capacitive touch keypads, low-cost motor control, and home appliance or HVAC control panels. The wide 2.3 V to 3.6 V supply range and -40C to +105C industrial temperature range also suit battery-powered and outdoor embedded designs.
When designing with this MCU, allocate at least 0.1uF decoupling near every VDD/AVDD pin pair, and ensure the 8 MHz primary oscillator or external crystal is placed close to the OSCI/OSCO pins to minimize EMI. PPS remapping should be reviewed carefully when porting firmware from older PIC32MX1/2/3 designs to avoid unintended peripheral conflicts.
This page synthesizes distributor pricing, drop-in alternatives from the same PIC32MX3/4 family, and practical design notes not aggregated in the manufacturer datasheet.
Alternatives de remplacement direct pour PIC32MX350F128H-I/MR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC32MX350F128H-I/MR (même facteur de forme et même empreinte) — différant par ADC, Package, Operating Temperature, USB, CTMU.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC32MX450F256H-I/MR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MX340F128H-80I/MR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MX330F064H-I/MR
✅ Remplacement direct✓ En stock
$4.1 / unité
Voir la fiche technique →PIC32MX340F256HT-80V/MR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MX340F128HT-80V/MR
✅ Remplacement direct✓ En stock
$3.92 / unité
Voir la fiche technique →PIC32MX270F512H-I/MR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MX270F512HT-50I/MR
✅ Remplacement direct✓ En stock
$4.74 / unité
Voir la fiche technique →PIC32MX350F128H-I/MR Valeurs maximales et caractéristiques électriques
| Core Architecture | MIPS32 M4K |
| Maximum CPU Speed | 100 MHz (150 DMIPS) |
| Program Flash Memory | 128 KB |
| Data SRAM | 32 KB |
| Operating Voltage | 2.3 V to 3.6 V |
| Température de fonctionnement | -40C to +105C (Industrial) |
| Boîtier | QFN-64 EP (MR), 9x9 mm with exposed pad |
| I/O Pins | 53 |
| ADC | 10-bit, up to 28 channels, 1 Msps |
| Analog Comparators | 2 |
| I2C Modules | 2 |
| SPI / I2S Modules | 2 (I2S-capable) |
| UART Modules | 2 (with LIN and IrDA support) |
| USB | USB 2.0 Full-Speed Device/Host/OTG |
| Parallel Master Port (PMP) | Yes |
| Peripheral Pin Select (PPS) | Yes |
| Charge Time Measurement Unit (CTMU) | Yes |
| Timers / IC / OC | 5 x 16-bit / 5 / 5 |
| Type de montage | Surface Mount |
| Niveau MSL | 1 (unlimited) |
| Statut RoHS | Compliant |
Configuration des broches de PIC32MX350F128H-I/MR
| Broche 1 | RA0 — General purpose I/O / AN0 / VREF- |
| Broche 2 | RA1 — General purpose I/O / AN1 / VREF+ |
| Broche 3 | RB0 — General purpose I/O / AN2 |
| Broche 4 | RB1 — General purpose I/O / AN3 |
| Broche 5 | RB2 — General purpose I/O / AN4 |
| Broche 6 | RB3 — General purpose I/O / AN5 |
| Broche 7 | RB4 — General purpose I/O / AN6 |
| Broche 8 | RB5 — General purpose I/O / AN7 |
| Broche 9 | RB6 — General purpose I/O / AN8 / PGEC1 |
| Broche 10 | RB7 — General purpose I/O / AN9 / PGED1 |
| Broche 11 | RB8 — General purpose I/O / AN10 |
| Broche 12 | RB9 — General purpose I/O / AN11 |
| Broche 13 | RB10 — General purpose I/O |
| Broche 14 | RB11 — General purpose I/O |
| Broche 15 | RB12 — General purpose I/O |
| Broche 16 | RB13 — General purpose I/O |
| Broche 17 | RB14 — General purpose I/O |
| Broche 18 | RB15 — General purpose I/O |
| Broche 19 | VDD — Core supply voltage 2.3-3.6 V |
| Broche 20 | VSS — Ground reference |
| Broche 21 | RC0 — General purpose I/O |
| Broche 22 | RC1 — General purpose I/O |
| Broche 23 | RC2 — General purpose I/O |
| Broche 24 | RC3 — General purpose I/O |
| Broche 25 | RC4 — General purpose I/O |
| Broche 26 | RC5 — General purpose I/O |
| Broche 27 | RC6 — General purpose I/O |
| Broche 28 | RC7 — General purpose I/O |
| Broche 29 | RC8 — General purpose I/O |
| Broche 30 | RC9 — General purpose I/O |
| Broche 31 | VDD — I/O supply voltage 2.3-3.6 V |
| Broche 32 | VSS — Ground reference |
| Broche 33 | RD0 — General purpose I/O |
| Broche 34 | RD1 — General purpose I/O |
| Broche 35 | RD2 — General purpose I/O |
| Broche 36 | RD3 — General purpose I/O |
| Broche 37 | RD4 — General purpose I/O |
| Broche 38 | RD5 — General purpose I/O |
| Broche 39 | RD6 — General purpose I/O |
| Broche 40 | RD7 — General purpose I/O |
| Broche 41 | RD8 — General purpose I/O |
| Broche 42 | RD9 — General purpose I/O |
| Broche 43 | RD10 — General purpose I/O |
| Broche 44 | RD11 — General purpose I/O |
| Broche 45 | RD12 — General purpose I/O |
| Broche 46 | RD13 — General purpose I/O |
| Broche 47 | RD14 — General purpose I/O |
| Broche 48 | RD15 — General purpose I/O |
| Broche 49 | VDD — Core supply voltage 2.3-3.6 V |
| Broche 50 | VSS — Ground reference |
| Broche 51 | RE0 — General purpose I/O |
| Broche 52 | RE1 — General purpose I/O |
| Broche 53 | RE2 — General purpose I/O |
| Broche 54 | RE3 — General purpose I/O |
| Broche 55 | RE4 — General purpose I/O |
| Broche 56 | RE5 — General purpose I/O |
| Broche 57 | RE6 — General purpose I/O |
| Broche 58 | RE7 — General purpose I/O |
| Broche 59 | AVDD — Analog supply voltage 3.0-3.6 V |
| Broche 60 | AVSS — Analog ground reference |
| Broche 61 | RF0 — General purpose I/O |
| Broche 62 | RF1 — General purpose I/O / USBID |
| Broche 63 | RF3 — General purpose I/O / USB D- |
| Broche 64 | RF2 — General purpose I/O / USB D+ |
Applications typiques
PIC32MX350F128H-I/MR convient pour 6 applications: USB Audio Device with I2S Codec, Capacitive Touch HMI Keypad, Graphics HMI with PMP-driven TFT LCD, USB Sensor Hub for Industrial Monitoring, Low-Cost Brushless DC Motor Controller, Home Appliance Control Panel.
USB Audio Device with I2S Codec
The PIC32MX350F128H-I/MR is well-suited for USB audio device designs that stream PCM data from a host to an external I2S DAC such as the PCM5102A or WM8960. Its integrated USB 2.0 Full-Speed OTG controller negotiates with the host without external PHY hardware, while two dedicated I2S/SPI modules carry I2S BCLK, LRCLK, and data lines to the external codec. With 128 KB Flash it accommodates full USB Audio class 1.0 firmware plus DSP filters, and 32 KB SRAM provides sufficient buffer space for high-bandwidth isochronous USB audio packets. The 100 MHz MIPS32 M4K core delivers 150 DMIPS, leaving ample MIPS headroom for real-time mixing and effect processing.
Recommandé
Capacitive Touch HMI Keypad
The PIC32MX350F128H-I/MR's integrated Charge Time Measurement Unit (CTMU) enables reliable capacitive touch sensing with no external analog front end, making it ideal for keypad, slider, and proximity-sensing HMI panels. Combined with Peripheral Pin Select, the same firmware can map touch electrodes to nearly any digital I/O pin, simplifying PCB routing for unusual keypad geometries. The 128 KB Flash accommodates mTouch reference firmware plus application logic, and the 10-bit ADC can read resistive overlays or proximity sensors alongside capacitive buttons. Industrial -40C to +105C temperature operation suits appliance, HVAC, and outdoor equipment front panels.
Recommandé
Graphics HMI with PMP-driven TFT LCD
The PIC32MX350F128H-I/MR's Parallel Master Port (PMP) provides an 8-bit or 16-bit data bus plus control signals to drive small TFT LCDs up to QVGA (320x240) resolution without an external controller. The 128 KB Flash can store fonts, icons, and small bitmap assets for graphical menus, while the 32 KB SRAM holds a framebuffer for animation and partial-screen updates. With PPS, the PMP can be remapped if the layout requires non-standard pin assignment. Designers building industrial control panels, home appliances, or test equipment benefit from the deterministic DMA-driven PMP throughput at 100 MHz CPU clock.
Recommandé
USB Sensor Hub for Industrial Monitoring
For USB-attached sensor hubs that bridge analog/digital sensors to a host PC, the PIC32MX350F128H-I/MR combines USB 2.0 Full-Speed device connectivity with two I2C buses, two SPI ports, two UARTs (LIN/IrDA capable), and a 10-bit ADC with up to 28 channels - enough to aggregate multiple sensor types on a single board. The 100 MHz MIPS32 M4K core executes protocol conversion, sensor fusion, and host-side USB transfers concurrently with 150 DMIPS of headroom. The 2.3 V to 3.6 V supply range and -40C to +105C industrial temperature range suit factory floor, building automation, and outdoor environment monitoring.
Recommandé
Low-Cost Brushless DC Motor Controller
The PIC32MX350F128H-I/MR's five 16-bit timers, five input captures, and five output compare modules provide the hardware PWM and feedback channels required for sensorless or sensored BLDC and PMSM motor control. PWM frequencies up to 80 kHz with 10 ns edge resolution drive 3-phase MOSFET bridges via gate drivers, while ADC sampling synchronised to the PWM triggers captures back-EMF for sensorless commutation. The CTMU can additionally measure DC-link current or temperature. The 128 KB Flash fits sensorless FOC reference firmware, and the 64-pin QFN EP package dissipates the MCU's moderate thermal load without active cooling in small motor drive enclosures.
Recommandé
Home Appliance Control Panel
The PIC32MX350F128H-I/MR is well-suited to consumer home appliance control panels combining a small TFT or character LCD, capacitive touch buttons, and a UART-connected main controller board. Peripheral Pin Select simplifies PCB routing when the keypad matrix, LCD bus, and main UART must coexist on shared pins. The 32 KB SRAM provides room for menu structures and small graphical buffers, and the USB device interface enables field firmware updates or factory test automation. The 2.3 V to 3.6 V supply range and -40C to +105C industrial temperature rating support kitchen appliances, washers, HVAC thermostats, and outdoor equipment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC32MX350F128H-I/MR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC32MX450F256H-I/MR | PIC32MX340F128H-80I/MR | PIC32MX330F064H-I/MR | PIC32MX340F256HT-80V/MR | PIC32MX270F512H-I/MR |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | QFN-64 EP (MR), 9x9 mm | QFN-64 EP (MR) - same | QFN-64 EP (MR) - same | QFN-64 EP (MR) - same | QFN-64 EP (MR) - same | QFN-64 EP (MR) - same |
| Core Architecture | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K |
| Maximum CPU Speed | 100 MHz (150 DMIPS) | 100 MHz | 80 MHz (-20%) | 100 MHz | 80 MHz (-20%) | 50 MHz (-50%) |
| Flash Memory | 128 KB | 256 KB (+100%) | 128 KB | 64 KB (-50%) | 256 KB (+100%) | 512 KB (+300%) |
| SRAM | 32 KB | 32 KB | 32 KB | 16 KB (-50%) | 32 KB | 64 KB (+100%) |
| USB | USB 2.0 Full-Speed OTG | USB 2.0 Hi-Speed OTG | USB 2.0 Full-Speed OTG | USB 2.0 Full-Speed OTG | USB 2.0 Full-Speed OTG | USB 2.0 Full-Speed OTG |
| Operating Voltage | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C |
Principaux différenciateurs
- Doubled Flash and SRAM versus the PIC32MX330F064H in the same QFN-64 footprint (vs PIC32MX330F064H-I/MR)
- Industry-standard Peripheral Pin Select (PPS) flexibility (vs PIC32MX340F128H-80I/MR)
- Higher 100 MHz CPU speed at 128 KB Flash tier (vs PIC32MX270F512H-I/MR)
Notes de conception
Place one 0.1uF ceramic decoupling capacitor adjacent to every VDD/AVDD pin pair (the PIC32MX350F128H-I/MR has 3 VDD/VSS pairs plus an AVDD/AVSS pair). Add a bulk 10uF ceramic or tantalum capacitor near the package to handle USB inrush current, since the USB transceiver draws up to 50 mA during enumeration. Tie VBUS through a 5V-tolerant pin to detect USB attachment, and route the internal 3.3V USB regulator output (VBUSON) to a 4.7uF bypass capacitor. AVDD must be at least 3.0 V for accurate ADC readings; use a ferrite bead or separate LDO if analog performance is critical.
Solder the central exposed pad of the QFN-64 (MR) package to a continuous ground pour with multiple stitching vias. The exposed pad carries substantial thermal current and serves as the dominant heat dissipation path. Keep all trace lengths to the 8 MHz crystal or external oscillator short and surrounded by a ground guard ring, and place the crystal load capacitors (typically 22 pF to 33 pF) close to the OSCI/OSCO pins. For USB D+/D- traces, maintain 90-ohm differential impedance and avoid routing near high-frequency switching signals.
Peripheral Pin Select (PPS) allows remapping of most digital peripherals to nearly any I/O pin, but the mapping is locked at runtime by writing to the PPS registers. Document the mapping in firmware with a single source-of-truth table so that PCB schematic labels match the actual pin assignments. Reserve a few spare GPIO pins connected to test pads for in-field debugging and boundary-scan troubleshooting. When using PMP for a TFT LCD, group the data lines D0..D15 together and route them in parallel to maintain signal skew.
Estimated: At 100 MHz with USB active and PMP writes to a TFT, sustained power dissipation can reach 0.5 W. With the QFN-64 EP thermal pad soldered to 1 sq-in of 2-oz copper on a 4-layer FR-4 board, theta_JA is approximately 25 C/W, allowing operation up to +105C ambient. Do not leave the CTMU module unconfigured when unused - leave its corresponding analog pin as digital input with the CTMU disabled, otherwise the input buffer may float and draw extra current. Always set the JTAGEN bit to 0 if JTAG pins are repurposed for general I/O via PPS, to avoid contention with debug probes.
USB D+/D- require 90-ohm differential routing with matching lengths within 2 mm. Place the USB common-mode choke and ESD protection diode within 5 mm of the USB connector, and avoid stubs on the D+/D- lines. For SPI-driven external devices running above 25 MHz, keep clock and data trace lengths matched and add a 22-ohm series resistor at the source end to dampen reflections. The PMP bus should not exceed 25 MHz on the QFN-64 package without a series resistor on the read strobe to limit ringing.
Informations de conformité
RoHS and lead-free per Microchip product page. Not AEC-Q100 qualified - automotive applications require PIC32MXxxx-Q1 variants. Industrial -40C to +105C temperature range per the I/MR suffix in the Microchip part numbering convention.
