Texas Instruments

TAS5630PHD - 300W Stereo Class-D Power Stage | Texas Instruments

Référence : TAS5630PHD ✓ Actif
50 V Vdss 64-HTQFP (14 mm x 14 mm) Package
MOQ : 1 |

TAS5630PHD Présentation

Texas Instruments TAS5630PHD is an analog-input Class-D audio power stage with integrated closed-loop feedback, rated for up to 300 W stereo output from a single 50 V supply in a 64-pin HTQFP package. Depending on the thermal configuration, the device can also support a 600 W mono output configuration.

A Class-D audio power stage is a semiconductor amplifier category that converts a PWM switching output into a filtered analog speaker signal. The TAS5630 belongs to the Class-D amplifier, audio power amplifier, and power management IC hierarchies. Its PurePath HD architecture integrates closed-loop feedback, linking the power-stage output to the analog input and reducing sensitivity to load-dependent nonlinear distortion.

The principal characteristics are 300 W maximum stereo output power, support for 4 Ω to 8 Ω speaker loads, and operation from a single 50 V supply. The device accepts analog audio input and can be configured for mono or stereo operation. These attributes suit high-power audio systems where efficiency, low heat loss, and accurate speaker-current feedback are important.

The integrated feedback architecture distinguishes the TAS5630 from basic open-loop Class-D solutions. It monitors output behavior through the feedback network, allowing the amplifier to correct nonlinear output distortion. Because achievable power depends strongly on the PCB, power-supply design, thermal interface material, and heat-sink configuration, a nominal 300 W rating should not be treated as a guaranteed output level in an arbitrary enclosure.

Typical applications include powered loudspeakers, active PA cabinets, professional audio consoles, home-theater power amplifiers, subwoofer amplifiers, and compact high-power stereo receivers. The 50 V supply requirement places the device in the high-voltage class-D power-stage category, requiring careful component spacing, a substantial thermal interface, and robust high-voltage layout practices.

Designers should follow the manufacturer datasheet reference layout for the exposed heat slug, power stages, output network, and analog input routing. The package must be coupled to an appropriately sized heat sink through high-performance thermal interface material. Power-supply and output-network components also require voltage, current, pulse-energy, and thermal ratings suitable for Class-D operation.

This product page combines the manufacturer power-stage capabilities, exact package information, thermal guidance, sourcing details, and replacement analysis. It also identifies where a true same-footprint replacement cannot be confirmed, preventing a merely similar amplifier from being presented as a drop-in substitute.

Alternatives de remplacement direct pour TAS5630PHD — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

TAS5630BPHD

✅ Remplacement direct
📦 64-HTQFP
Same 300 W stereo family and 64-HTQFP package class; output rating differs by 0 W, while exact B-version pin and feature distinctions require datasheet confirmation.

📋 Alternative de référence (hors catalogue)

TAS5631BPHD

✅ Remplacement direct
📦 64-HTQFP
Related 300 W stereo Class-D power stage with the same 300 W nominal output class; control, protection, and pin-level differences require direct comparison before substitution.

📋 Alternative de référence (hors catalogue)

TAS5630PHD Valeurs maximales et caractéristiques électriques

Product Type Analog-input Class-D audio power stage
Maximum Stereo Output Power 300 W
Maximum Mono Output Power 600 W
Supported Speaker Load 4 ohm to 8 ohm
Tension d'alimentation 50 V
Feedback Architecture Integrated closed-loop PurePath HD feedback
Input Type Analog input
Configuration de sortie 1-channel mono or 2-channel stereo
Boîtier 64-HTQFP (14 mm x 14 mm)
Type de montage Surface mount
Exposed Thermal Pad Present
Statut RoHS Compliant
Thermal Interface Requirement High-performance thermal interface material between package heat slug and heat sink

Guide de configuration des broches du TAS5630PHD 64-htqfp (14 mm x 14 mm)

Configuration des broches du TAS5630PHD (boîtier 64-htqfp (14 mm x 14 mm)). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.

Schéma de brochage du boîtier 64-htqfp (14 mm x 14 mm) pour le TAS5630PHD

Aucune donnée de brochage détaillée disponible pour TAS5630PHD.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

TAS5630PHD convient pour 6 applications: Powered Professional Loudspeaker, Active Subwoofer Amplifier, Home-Theater Power Amplifier, PA and Venue Amplifier, Digital-Audio Power Converter, High-Power Audio Amplifier Rack.

🔊

Powered Professional Loudspeaker

The TAS5630PHD fits high-output active loudspeaker designs because it can provide up to 300 W per channel for 4 Ω to 8 Ω drivers from a single 50 V supply. It is placed in the Class-D output stage behind the mixer or preamplifier, with analog input filtering, supply decoupling, speaker output filtering, and protection circuitry implemented according to the manufacturer reference design. Integrated PurePath HD feedback helps reduce load-dependent distortion. The 64-HTQFP exposed heat slug must be coupled to a substantial heat sink through high-performance thermal interface material, because achievable continuous power depends on the PCB and thermal configuration.

🎧

Active Subwoofer Amplifier

The TAS5630PHD is suitable for an active subwoofer power amplifier configured for high output into a 4 Ω or 8 Ω driver. Its analog-input architecture accepts a line-level signal from a crossover or source module, while the integrated PurePath HD feedback system supports accurate output-current control and lower load-dependent distortion. The single 50 V supply architecture simplifies system power distribution while still requiring carefully rated bulk and high-frequency decoupling. Output protection, DC-offset behavior, clipping, and thermal safeguards must be evaluated against the loudspeaker impedance and continuous program power.

🏠

Home-Theater Power Amplifier

The TAS5630PHD can serve as the main Class-D output stage of a high-power home-theater or multichannel power amplifier. Its 300 W per-channel capability covers demanding speaker configurations, while analog inputs can be driven from preamplifier channels or passive crossover networks. The 64-HTQFP package provides a direct path from the power device to a chassis heat sink, but signal integrity depends on keeping analog input routing away from switching nodes. Output inductors, filter capacitors, speaker relays, and protection components must be selected for the intended impedance and power level.

🏭

PA and Venue Amplifier

For portable or installed PA amplification, the TAS5630PHD provides a high-efficiency power-conversion solution for driving passive 4 Ω or 8 Ω loudspeaker arrays. Its integrated closed-loop PurePath HD feedback is valuable in venues where speaker impedance varies with frequency and parallel cabinets reduce the effective load. The amplifier should be paired with input limiting, DC protection, temperature monitoring, and a system-level speaker disconnect strategy. Its 50 V supply requirement and exposed thermal package make power conversion, airflow, and heat-sink design central to maintaining output performance.

🖥️

Digital-Audio Power Converter

The TAS5630PHD can form the final analog power-conversion section of a digital-audio playback system. A digital audio processor supplies an analog signal to the Class-D input, and the integrated feedback network drives the speaker output while correcting nonlinear errors. This arrangement supports high output power without placing a linear output stage after the digital signal chain. Analog input routing should remain short and isolated from the switching stage, while the output network must be designed around the target 4 Ω or 8 Ω impedance and the device's high-power switching behavior.

🖥️

High-Power Audio Amplifier Rack

The TAS5630PHD is appropriate for rack-mount professional amplifiers where each channel requires hundreds of watts and efficient power delivery. Its Class-D topology reduces the heat that must be removed compared with an equivalent linear output stage, but the device still requires a carefully engineered heat spreader, interface material, and forced or natural-convection enclosure design. The single 50 V supply architecture supports common high-power bus concepts, while the analog input section benefits from shielded routing and clean grounding. Production designs should include independent channel protection and temperature monitoring around the exposed package.

Récapitulatif des produits recommandés

TAS5630BPHD Related power-stage family member for design evaluation Utilisé dans : Powered Professional Loudspeaker, Active Subwoofer Amplifier, Home-Theater Power Amplifier, PA and Venue Amplifier, Digital-Audio Power Converter, High-Power Audio Amplifier Rack TAS5631BPHD Related 300 W-class Class-D power stage Utilisé dans : Powered Professional Loudspeaker, Active Subwoofer Amplifier, Home-Theater Power Amplifier, PA and Venue Amplifier, Digital-Audio Power Converter, High-Power Audio Amplifier Rack
What is the TAS5630PHD?
The TAS5630PHD is a Texas Instruments analog-input Class-D audio power stage with integrated PurePath HD closed-loop feedback. According to the manufacturer product page and datasheet, it can deliver up to 300 W of stereo output from a single 50 V supply when the PCB and thermal configuration support that level. The device is packaged in a 64-HTQFP measuring 14 mm by 14 mm and can also be configured for high-power mono operation.
How much power can the TAS5630PHD output?
The TAS5630PHD can drive up to 300 W per channel in stereo operation and up to 600 W in mono operation, subject to the thermal configuration. Texas Instruments states that achievable output power depends on the heat-sink, thermal-interface, PCB, and supply configuration. A 300 W result should therefore be validated in the final mechanical and electrical assembly rather than inferred solely from the device rating.
What speaker impedances can the TAS5630PHD drive?
The TAS5630PHD is intended for 4 Ω to 8 Ω speaker loads. The manufacturer product page describes up to 300 W of stereo output from a single 50 V supply, with the exact output level dependent on the target application's thermal design. Designers should also verify speaker power tolerance, amplifier protection behavior, DC offset, and the output-filter component ratings for the selected load.
What is PurePath HD in the TAS5630PHD?
PurePath HD is the integrated closed-loop feedback technology used in the TAS5630PHD. According to the Texas Instruments product page, it is a feedback architecture that corrects output distortion by linking the analog input to the power stage through closed-loop feedback. The result is lower load-dependent distortion than a conventional open-loop Class-D power stage while retaining the efficiency associated with Class-D operation.
Where can I download the TAS5630PHD datasheet PDF?
The official TAS5630PHD datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/tas5630.pdf. It contains the authoritative electrical characteristics, package information, thermal data, pin descriptions, application circuit, and power-supply guidance. Use the pin-description table and reference layout in that document when assigning PCB nets or planning the heat-sink interface.
Where can I find the TAS5630PHD pinout?
The TAS5630PHD pinout is documented in the Texas Instruments datasheet and must be assigned from the package drawing and pin-description table rather than inferred from a generic 64-pin diagram. The device uses a 64-HTQFP package with an exposed thermal slug. Keep the high-voltage switching nodes and exposed thermal region clear of sensitive analog and control traces when implementing the reference layout.
Does the TAS5630PHD require a heatsink?
Yes, the TAS5630PHD requires careful thermal management for high-power operation. Texas Instruments specifically identifies a high-performance thermal interface material between the exposed package heat slug and the heat sink as important to achieving the stated output capability. The heat-sink area must be derived from the estimated device loss, ambient temperature, maximum junction temperature, and the PCB thermal path used in the final assembly.
How is the TAS5630PHD power supply designed?
The TAS5630PHD operates from a single 50 V supply in its high-power application configuration. The power stage therefore requires a supply with suitable voltage margin, low ripple, transient response, and current capability for the selected load. Decoupling and layout must follow the manufacturer reference design, with particular attention to high-current switching loops and the separation of sensitive analog-input routing.
What is the best drop-in replacement for the TAS5630PHD?
No alternative can be presented as a confirmed drop-in replacement for the TAS5630PHD from the available manufacturer and comparison information. TAS5630BPHD is the closest same-family candidate because it retains the same core power-stage identity and 64-pin package family, but the exact B-version distinctions and land-pattern compatibility must be checked in its datasheet before substitution. Use the Request a Quote form on this page when an approved-source replacement is required.
Can TAS5631BPHD replace the TAS5630PHD?
TAS5631BPHD should not be treated as an automatic drop-in replacement for the TAS5630PHD. The comparison data identifies both devices as related 300 W-class Texas Instruments power stages, but it does not establish identical pin assignments, thermal pad geometry, control logic, or protection behavior. Compare the two manufacturer datasheets and confirm every package, signal, and timing requirement before considering a board revision.
What can replace the TAS5630PHD?
The safest replacement is an exact-orderable variant with a manufacturer-confirmed identical footprint, pinout, electrical limits, and thermal interface arrangement. TAS5630BPHD is a close same-family option to evaluate, while TAS5631BPHD is a related higher-performance family member requiring a full pin and control comparison. No cross-brand equivalent has been confirmed as drop-in compatible, so PCB or system changes must not be assumed.
When should I choose the TAS5630PHD over TAS5631BPHD?
Choose the TAS5630PHD when a 300 W analog-input Class-D stage with PurePath HD integrated feedback and a 64-HTQFP power-stage package fits the mechanical and electrical design. Consider TAS5631BPHD only after verifying its pin assignments, control interface, protection behavior, and output characteristics against the TAS5630PHD implementation. The related family may offer different features, but similarity in power class does not establish drop-in compatibility.
Is the TAS5630PHD suitable for a powered PA speaker?
The TAS5630PHD is suitable in principle for a high-power powered PA speaker that uses 4 Ω to 8 Ω drivers and a 50 V Class-D power-stage architecture. Its 300 W stereo capability makes it relevant to demanding active loudspeaker designs, but final suitability depends on thermal dissipation, supply capacity, protection strategy, output filtering, and the continuous versus peak power required by the system.
Is there a Texas Instruments equivalent to the TAS5630PHD?
Texas Instruments offers related TAS5630 and TAS5631 family parts, but an equivalent designation alone does not prove drop-in compatibility. TAS5630BPHD is the nearest same-family candidate identified in the comparison material, while TAS5631BPHD provides a related 300 W-class power-stage option. Verify the exact ordering code, pinout, exposed-pad requirements, and datasheet limits before using either part on an unmodified TAS5630PHD board.
Where can I buy the TAS5630PHD and check its lead time?
Use the Request a Quote form on this page to request TAS5630PHD availability, current lead time, and order quantity from XAIPART. The form allows purchasing teams to obtain a current quotation without relying on a static price that may have changed. For production planning, request the chosen package suffix and required quantity so the order confirmation can reflect the correct orderable configuration.
What are the key specifications of the TAS5630PHD that engineers should know?
The key TAS5630PHD specifications are analog input, Class-D operation, integrated PurePath HD closed-loop feedback, up to 300 W stereo output, up to 600 W mono output, support for 4 Ω to 8 Ω loads, a single 50 V supply, and a 64-HTQFP package. According to Texas Instruments, achievable power depends on the thermal configuration, so the power rating, heat sink, thermal interface, PCB, and supply must be designed as one system.

Données de référence d'ingénierie pour TAS5630PHD — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose TAS5630PHD for a 300 W-per-channel analog-input Class-D design using 4 Ω or 8 Ω speakers and a 50 V supply architecture, particularly when integrated PurePath HD feedback and a high-power exposed thermal package are priorities. TAS5630BPHD is the closest same-family candidate for an existing board review, but confirm the B-version differences, pin assignments, ordering code, and exposed-pad geometry before treating it as a drop-in part. TAS5631BPHD belongs to a related family with a similar 300 W stereo class; consider it only when its control interface, protection behavior, pinout, and thermal requirements have been checked against the target board. No cross-brand replacement is confirmed as pin-compatible. For all choices, perform thermal, electrical, protection, and loudspeaker-impedance validation in the final enclosure because the power rating depends on the complete hardware configuration.

Comparaison avec les alternatives

Paramètre Ce produit TAS5630BPHD TAS5631BPHD
Brand Texas Instruments Texas Instruments Texas Instruments
Package 64-HTQFP (14 mm x 14 mm) 64-HTQFP 64-HTQFP
Amplifier Type Class-D analog-input power stage Class-D power stage Class-D power stage
Maximum Stereo Output Power 300 W 300 W 300 W

Principaux différenciateurs

  • High output power in an integrated analog-input Class-D stage (vs TAS5631BPHD)
  • Same-family upgrade path (vs TAS5631BPHD)
  • Closest identified same-family configuration (vs TAS5630BPHD)

Notes de conception

Treat the exposed heat slug as the primary thermal path. Texas Instruments identifies high-performance thermal interface material between the slug and heat sink as important for achieving the 300 W stereo capability. Size the heat sink from the calculated worst-case conduction and switching loss, ambient temperature, target junction-temperature limit, and the PCB thermal resistance. Verify the assembled thermal path because the advertised power level is conditional on the target application's thermal configuration.

Use the manufacturer reference layout rather than a generic Class-D layout. Keep the high-current output and supply loops compact, provide the required local decoupling at the power-stage pins, and route the analog input away from switching nodes. The high-current and high-voltage nature of this stage makes copper area, via arrangement, return-current control, and clean grounding as important as the nominal component values.

Design the single 50 V supply path for the selected continuous and transient output demand. Include local high-frequency bypass capacitors and bulk energy storage close to the power stage, while checking component voltage, ripple-current, pulse-energy, and thermal ratings. Account for startup current and power-supply recovery after clipping or load transitions so the amplifier does not cause the system rail to collapse during normal program changes.

Do not equate a 300 W device rating with guaranteed continuous output from an arbitrary board or heat sink. Validate speaker impedance, filter-component ratings, DC offset, clipping behavior, thermal protection, and the exposed-pad footprint against the final assembly. Also avoid selecting a related family member solely from its 300 W headline rating; verify every pin, control signal, protection function, and land-pattern detail in the applicable manufacturer datasheet.

Informations de conformité

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Yes
Sans halogène
Unknown
Minerais de conflit
Unknown

The exact-MPN distributor listing identifies the device as ROHS3 compliant and lead-free. No additional certification claims are made for REACH, halogen-free status, or conflict-minerals compliance.

Données vérifiées le : 2026-11-10 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

TAS5630PHD datasheet TAS5630PHD datasheet pdf TAS5630PHD pinout TAS5630PHD schematic TAS5630PHD equivalent TAS5630PHD replacement TAS5630PHD cross reference TAS5630PHD vs TAS5631BPHD TAS5630PHD footprint TAS5630PHD application circuit Texas Instruments TAS5630PHD TAS5630 300W Class-D amplifier TAS5630PHD 64-HTQFP TAS5630PHD price TAS5630PHD stock

Composants & termes associés

Texas Instruments TAS5630PHD TAS5630BPHD TAS5631BPHD Class-D amplifier audio power amplifier analog-input power stage PurePath HD integrated closed-loop feedback 300 W stereo output 600 W mono output 50 V supply 4 ohm speaker load 8 ohm speaker load 64-HTQFP HTQFP package family surface-mount package exposed heat slug thermal interface material Class-D output filter powered loudspeaker active subwoofer amplifier professional audio amplifier RoHS
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ