TAS5630PHD - 300W Stereo Class-D Power Stage | Texas Instruments
MPN: TAS5630PHD ✓ Hoạt độngTAS5630PHD Tóm tắt
A Class-D audio power stage is a semiconductor amplifier category that converts a PWM switching output into a filtered analog speaker signal. The TAS5630 belongs to the Class-D amplifier, audio power amplifier, and power management IC hierarchies. Its PurePath HD architecture integrates closed-loop feedback, linking the power-stage output to the analog input and reducing sensitivity to load-dependent nonlinear distortion.
The principal characteristics are 300 W maximum stereo output power, support for 4 Ω to 8 Ω speaker loads, and operation from a single 50 V supply. The device accepts analog audio input and can be configured for mono or stereo operation. These attributes suit high-power audio systems where efficiency, low heat loss, and accurate speaker-current feedback are important.
The integrated feedback architecture distinguishes the TAS5630 from basic open-loop Class-D solutions. It monitors output behavior through the feedback network, allowing the amplifier to correct nonlinear output distortion. Because achievable power depends strongly on the PCB, power-supply design, thermal interface material, and heat-sink configuration, a nominal 300 W rating should not be treated as a guaranteed output level in an arbitrary enclosure.
Typical applications include powered loudspeakers, active PA cabinets, professional audio consoles, home-theater power amplifiers, subwoofer amplifiers, and compact high-power stereo receivers. The 50 V supply requirement places the device in the high-voltage class-D power-stage category, requiring careful component spacing, a substantial thermal interface, and robust high-voltage layout practices.
Designers should follow the manufacturer datasheet reference layout for the exposed heat slug, power stages, output network, and analog input routing. The package must be coupled to an appropriately sized heat sink through high-performance thermal interface material. Power-supply and output-network components also require voltage, current, pulse-energy, and thermal ratings suitable for Class-D operation.
This product page combines the manufacturer power-stage capabilities, exact package information, thermal guidance, sourcing details, and replacement analysis. It also identifies where a true same-footprint replacement cannot be confirmed, preventing a merely similar amplifier from being presented as a drop-in substitute.
Bộ thay thế dễ dàng lắp đặt cho TAS5630PHD — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TAS5630BPHD
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TAS5631BPHD
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TAS5630PHD Tỷ lệ tối đa & tính chất điện
| Product Type | Analog-input Class-D audio power stage |
| Maximum Stereo Output Power | 300 W |
| Maximum Mono Output Power | 600 W |
| Supported Speaker Load | 4 ohm to 8 ohm |
| Điện áp cung cấp | 50 V |
| Feedback Architecture | Integrated closed-loop PurePath HD feedback |
| Input Type | Analog input |
| Cấu hình đầu ra | 1-channel mono or 2-channel stereo |
| Hộp | 64-HTQFP (14 mm x 14 mm) |
| Kiểu lắp đặt | Surface mount |
| Exposed Thermal Pad | Present |
| Trạng thái RoHS | Compliant |
| Thermal Interface Requirement | High-performance thermal interface material between package heat slug and heat sink |
Hướng dẫn cấu hình chân TAS5630PHD 64-htqfp (14 mm x 14 mm)
Cấu hình chân cho TAS5630PHD (64-htqfp (14 mm x 14 mm) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TAS5630PHD.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TAS5630PHD phù hợp cho 6 Áp dụngs: Powered Professional Loudspeaker, Active Subwoofer Amplifier, Home-Theater Power Amplifier, PA and Venue Amplifier, Digital-Audio Power Converter, High-Power Audio Amplifier Rack.
Powered Professional Loudspeaker
The TAS5630PHD fits high-output active loudspeaker designs because it can provide up to 300 W per channel for 4 Ω to 8 Ω drivers from a single 50 V supply. It is placed in the Class-D output stage behind the mixer or preamplifier, with analog input filtering, supply decoupling, speaker output filtering, and protection circuitry implemented according to the manufacturer reference design. Integrated PurePath HD feedback helps reduce load-dependent distortion. The 64-HTQFP exposed heat slug must be coupled to a substantial heat sink through high-performance thermal interface material, because achievable continuous power depends on the PCB and thermal configuration.
Được đề xuất
Active Subwoofer Amplifier
The TAS5630PHD is suitable for an active subwoofer power amplifier configured for high output into a 4 Ω or 8 Ω driver. Its analog-input architecture accepts a line-level signal from a crossover or source module, while the integrated PurePath HD feedback system supports accurate output-current control and lower load-dependent distortion. The single 50 V supply architecture simplifies system power distribution while still requiring carefully rated bulk and high-frequency decoupling. Output protection, DC-offset behavior, clipping, and thermal safeguards must be evaluated against the loudspeaker impedance and continuous program power.
Được đề xuất
Home-Theater Power Amplifier
The TAS5630PHD can serve as the main Class-D output stage of a high-power home-theater or multichannel power amplifier. Its 300 W per-channel capability covers demanding speaker configurations, while analog inputs can be driven from preamplifier channels or passive crossover networks. The 64-HTQFP package provides a direct path from the power device to a chassis heat sink, but signal integrity depends on keeping analog input routing away from switching nodes. Output inductors, filter capacitors, speaker relays, and protection components must be selected for the intended impedance and power level.
Được đề xuất
PA and Venue Amplifier
For portable or installed PA amplification, the TAS5630PHD provides a high-efficiency power-conversion solution for driving passive 4 Ω or 8 Ω loudspeaker arrays. Its integrated closed-loop PurePath HD feedback is valuable in venues where speaker impedance varies with frequency and parallel cabinets reduce the effective load. The amplifier should be paired with input limiting, DC protection, temperature monitoring, and a system-level speaker disconnect strategy. Its 50 V supply requirement and exposed thermal package make power conversion, airflow, and heat-sink design central to maintaining output performance.
Được đề xuất
Digital-Audio Power Converter
The TAS5630PHD can form the final analog power-conversion section of a digital-audio playback system. A digital audio processor supplies an analog signal to the Class-D input, and the integrated feedback network drives the speaker output while correcting nonlinear errors. This arrangement supports high output power without placing a linear output stage after the digital signal chain. Analog input routing should remain short and isolated from the switching stage, while the output network must be designed around the target 4 Ω or 8 Ω impedance and the device's high-power switching behavior.
Được đề xuất
High-Power Audio Amplifier Rack
The TAS5630PHD is appropriate for rack-mount professional amplifiers where each channel requires hundreds of watts and efficient power delivery. Its Class-D topology reduces the heat that must be removed compared with an equivalent linear output stage, but the device still requires a carefully engineered heat spreader, interface material, and forced or natural-convection enclosure design. The single 50 V supply architecture supports common high-power bus concepts, while the analog input section benefits from shielded routing and clean grounding. Production designs should include independent channel protection and temperature monitoring around the exposed package.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TAS5630PHD — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TAS5630BPHD | TAS5631BPHD |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 64-HTQFP (14 mm x 14 mm) | 64-HTQFP | 64-HTQFP |
| Amplifier Type | Class-D analog-input power stage | Class-D power stage | Class-D power stage |
| Maximum Stereo Output Power | 300 W | 300 W | 300 W |
Bảo phân biệt quan trọng
- High output power in an integrated analog-input Class-D stage (vsTAS5631BPHD)
- Same-family upgrade path (vsTAS5631BPHD)
- Closest identified same-family configuration (vsTAS5630BPHD)
Ghi chú thiết kế
Treat the exposed heat slug as the primary thermal path. Texas Instruments identifies high-performance thermal interface material between the slug and heat sink as important for achieving the 300 W stereo capability. Size the heat sink from the calculated worst-case conduction and switching loss, ambient temperature, target junction-temperature limit, and the PCB thermal resistance. Verify the assembled thermal path because the advertised power level is conditional on the target application's thermal configuration.
Use the manufacturer reference layout rather than a generic Class-D layout. Keep the high-current output and supply loops compact, provide the required local decoupling at the power-stage pins, and route the analog input away from switching nodes. The high-current and high-voltage nature of this stage makes copper area, via arrangement, return-current control, and clean grounding as important as the nominal component values.
Design the single 50 V supply path for the selected continuous and transient output demand. Include local high-frequency bypass capacitors and bulk energy storage close to the power stage, while checking component voltage, ripple-current, pulse-energy, and thermal ratings. Account for startup current and power-supply recovery after clipping or load transitions so the amplifier does not cause the system rail to collapse during normal program changes.
Do not equate a 300 W device rating with guaranteed continuous output from an arbitrary board or heat sink. Validate speaker impedance, filter-component ratings, DC offset, clipping behavior, thermal protection, and the exposed-pad footprint against the final assembly. Also avoid selecting a related family member solely from its 300 W headline rating; verify every pin, control signal, protection function, and land-pattern detail in the applicable manufacturer datasheet.
Thông tin tuân thủ
The exact-MPN distributor listing identifies the device as ROHS3 compliant and lead-free. No additional certification claims are made for REACH, halogen-free status, or conflict-minerals compliance.