TLV2462CP - Dual 6.4MHz RRIO Op Amp | Texas Instruments
Référence : TLV2462CP ✓ ActifTLV2462CP Présentation
A rail-to-rail input/output operational amplifier is an amplifier whose input common-mode range and output voltage swing can operate close to the positive and negative supply rails. This rail-to-rail, or RRIO, architecture belongs to the operational-amplifier hierarchy within analog and mixed-signal ICs. It is especially useful when signal levels approach the available supply voltage or when the input source can vary across most of the system voltage range.
The TLV2462CP provides 6.4 MHz gain-bandwidth product, rail-to-rail input and output behavior, and approximately 500 µA supply current per channel. Its 80 mA output-drive capability gives designers more margin when driving a load, sampling network, or downstream circuit. The dual-channel configuration provides two amplifiers in one package, reducing board area when a design needs matched signal-conditioning paths.
Technically, the device is positioned as a low-power, general-purpose RRIO amplifier. Its 6.4 MHz bandwidth supports higher-frequency signal paths than a conventional low-frequency precision amplifier, while the approximately 500 µA per-channel current supports portable equipment. Because input offset voltage, noise density, slew rate, common-mode range, and shutdown behavior are not stated in the product results, those characteristics should be confirmed in the manufacturer datasheet before finalizing a precision or noise-sensitive design.
Typical uses include portable sensor conditioning, low-level signal amplification, active filtering, audio preamplification, data acquisition, and general buffering. The dual channels can support paired signal paths, such as differential signal conditioning or simultaneous sensing and filtering. Through-hole PDIP construction can also simplify prototyping, educational builds, repair, and manual assembly where surface-mount packages are inconvenient.
The primary design consideration is supply and output-range planning. Confirm that the input source remains within the amplifier's common-mode range, that the required output amplitude stays inside the output-swing limits, and that the connected load does not exceed the available drive capability. Place bypass capacitors close to the supply pins and use short feedback paths to limit parasitic effects and preserve the intended response.
This product guide combines the manufacturer family specifications, package information, sourcing guidance, compatible alternatives, and practical design considerations. It is intended to help engineers identify whether the TLV2462CP's dual RRIO architecture, low-power operation, 6.4 MHz bandwidth, and PDIP package fit a new analog circuit before detailed design verification.
Alternatives de remplacement direct pour TLV2462CP — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec TLV2462CP (même facteur de forme et même empreinte) — différant par Package, Amplifier Type, Mounting Type, Number of Channels, Input Common-Mode Range.
TLV2462IPE4
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TLV2462CPE4
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TLV2462ID
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →LMV358IDT
✅ Remplacement direct✓ En stock
$0.13 / unité
Voir la fiche technique →TLV2462CP Valeurs maximales et caractéristiques électriques
| Amplifier Type | Dual operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 6 V |
| Gain-Bandwidth Product | 6.4 MHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Supply Current per Channel | 500 µA/channel |
| Output Drive Capability | 80 mA |
| Low-Power Operation | Low-power RRIO operational amplifier |
| Boîtier | 8-pin PDIP (P) |
| Type de montage | Through-hole |
| Statut RoHS | Compliant |
Guide de configuration des broches du TLV2462CP 8-pin pdip (p)
Configuration des broches du TLV2462CP (boîtier 8-pin pdip (p)). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour TLV2462CP.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
TLV2462CP convient pour 6 applications: Portable Sensor Signal Conditioning, Industrial Data Acquisition, Low-Noise Audio Preamplification, Active Filtering and Waveform Conditioning, Power and Control Signal Buffering, Prototyping and Repair Electronics.
Portable Sensor Signal Conditioning
The TLV2462CP fits two-stage conditioning for portable sensors because its approximately 500 µA supply current per channel limits the amplifier's contribution to battery drain. The dual 6.4 MHz channels can amplify or buffer adjacent sensor signals while preserving small signal details across a broad frequency range. Rail-to-rail input operation is useful when sensor outputs move near either supply rail, while rail-to-rail output gives the next stage more usable voltage range. Confirm the input common-mode limits, output swing, and noise density in the manufacturer datasheet before selecting the gain and filter values.
Recommandé
Industrial Data Acquisition
The TLV2462CP is suitable for intermediate buffering in industrial data-acquisition systems that need two signal paths, a 6.4 MHz gain-bandwidth product, and relatively low channel current. One channel can condition a sensor or converter output while the other supports a reference, filter, or auxiliary signal path. Its approximately 80 mA output-drive capability provides more margin for moderate capacitive and resistive loads than a minimum-area micropower amplifier. Industrial use still requires validation against the actual temperature range, noise, offset, common-mode error, and electromagnetic environment.
Recommandé
Low-Noise Audio Preamplification
The TLV2462CP can serve as a dual audio preamplifier in portable and compact audio equipment because both input and output stages are designed for rail-to-rail operation. The two amplifiers can support left and right channels, or one channel can provide gain while the other buffers a control or headphone-driver path. Its 6.4 MHz gain-bandwidth product is ample for many audio-band tasks, while approximately 500 µA per channel supports low-power operation. Confirm input noise density, distortion, output swing, and load stability because those parameters are not stated in the product result.
Recommandé
Active Filtering and Waveform Conditioning
The TLV2462CP's 6.4 MHz gain-bandwidth product makes it appropriate for active filters and waveform-conditioning stages where ordinary low-frequency op amps may lack bandwidth. Its dual configuration can implement two independent filter sections or a cascaded second-order network. Rail-to-rail input and output behavior improves usable signal range in low-voltage systems, and the approximately 80 mA drive specification helps when the filter drives an ADC input or short cable. Check phase margin, capacitive loading, and gain-bandwidth interaction against the manufacturer's stability guidance.
Recommandé
Power and Control Signal Buffering
The TLV2462CP can buffer low-level control, feedback, and sensing signals in a power-control subsystem when the source impedance and output load are moderate. Its rail-to-rail input range supports signals approaching the supply limits, while the approximately 80 mA output-drive capability gives more load margin than a very low-power comparator-style buffer. The dual arrangement can process a command signal and a feedback signal independently. Verify stable operation with the actual load, cable capacitance, supply ripple, and feedback topology before deployment.
Recommandé
Prototyping and Repair Electronics
The TLV2462CP's 8-pin PDIP package makes it convenient for through-hole prototypes, educational circuits, repair work, and manually assembled instruments. The DIP footprint simplifies socket use and board-level replacement compared with a surface-mount package. Electrically, the device offers two independent 6.4 MHz RRIO channels with approximately 500 µA supply current per channel, so it can replace many general-purpose dual-amplifier layouts. Before soldering, confirm the eight-pin numbering from the manufacturer datasheet and verify that the replacement circuit does not rely on shutdown, offset, or temperature specifications unique to another grade.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TLV2462CP — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TLV2462IPE4 | TLV2462CPE4 | TLV2462ID | LMV358 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | 8-pin PDIP |
| Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Rail-to-Rail Input | Yes | Yes | Yes | Yes | No; rail-to-rail output only |
| Rail-to-Rail Output | Yes | Yes | Yes | Yes | Yes |
| Device Class | Low-power RRIO operational amplifier | Low-power RRIO operational amplifier | Low-power RRIO operational amplifier | Dual high-speed signal-processing amplifier | Dual low-power operational amplifier |
Principaux différenciateurs
- Broader input operating range than the LMV358 drop-in candidate (vs LMV358)
- Clearly defined 6.4 MHz signal-processing bandwidth (vs TLV2462ID)
- Dual low-power channels in one through-hole package (vs TLV2462CPE4)
- Moderate output-drive margin for compact analog systems (vs LMV358)
Notes de conception
Do not treat the 8-pin PDIP footprint as proof of electrical equivalence. The LMV358 is a documented 8-DIP drop-in candidate, but the available cross-reference identifies rail-to-rail output only, while the TLV2462CP is a rail-to-rail input/output device. Check the input common-mode range, offset voltage, noise, bandwidth, output swing, and load stability against the final signal source and load before substitution.
Place input, output, and supply bypass components close to their associated pins. Keep feedback components and signal traces short to limit parasitic capacitance and maintain the intended response from the 6.4 MHz gain-bandwidth product. For through-hole prototype boards, route sensitive input signals away from the power-entry path and relay or switching-node wiring to reduce injected noise into the high-impedance amplifier input.
Estimated supply-current consumption at the 6 V maximum rating is approximately 1.0 mA for both channels because the cited current is 500 µA per channel. This estimate excludes input bias current, output-current demand, leakage, and external-load effects. Confirm the actual quiescent current and output-current dissipation at the intended supply voltage using the manufacturer operating-characteristics curves before sizing the power rail.
Check capacitive loading at each output because the cited 80 mA drive capability does not by itself define the stable bandwidth for every load. Use the manufacturer stability guidance, especially when driving long PCB traces, ADC inputs, cables, or capacitive sensor devices. If a large load is required, insert a small isolation resistor and verify settling behavior at the intended closed-loop gain.
Informations de conformité
RoHS-compliant status is identified in the TLV2462ID and TLV2462CP comparison information. No authoritative statements for REACH, lead-free status, halogen-free status, conflict minerals, or automotive qualification were found.